--||-- How To Make Air Coil inductors --||--

Рет қаралды 49,484

Жыл бұрын

Hello again, in this video you will find how to make high quality 1 mH air core coil inductor or any other value for your high fidelity speaker's crossoer or for any other electronic project.
thank you for your support to hommeaudio channel, i hope you like the video.
link to application :
coil32.net/download-coil64-fo...
tinyurl.com/4yhfhshx
Very interesting video to watch on my channel :
• --||-- How To make Rub...
hifi speakers,
crossover audiophile,
audiophile capacitors.
nichicon capacitors.
elna silmic
audyn capacitors
jbl crossover
kef speakers
klipsch crossover

Пікірлер: 73

@eduardoquintanaavila.6290 Ай бұрын

Excelente, esto es un trabajo profesional. El mejor de los videos para la elaboración de un inductor de manera manual. Gracias por compartir la informacion. Saludos desde México.

@homemade_audio Ай бұрын

Thank you so much for your comment 🥰🙏🙏🙏 Like this words give me power to do more and more 👍

@derekfreeman3562 Жыл бұрын

In a perfect world, wed all have a machine shop handy

@homemade_audio Жыл бұрын

thank you

@jimconnelly816 Жыл бұрын

Are you kidding!!outstanding videos brother, thank you.

@homemade_audio Жыл бұрын

Thank you my friend, it really took me a lot of time. like ribbon speaker video, i want to make something special.

@sumguysr Жыл бұрын

Cool video. Thanks for sharing. I think if I get into winding my own I'll try to come up with a 3d printed gadget for it. I like your impregnation and sip tie method though.

@homemade_audio Жыл бұрын

Thank you for your comment 👍 this video took me a lounge time to make it, i hope you love it 🥰🥰🥰 You welcome 🙏🙏🙏

@davidzoller9617 Жыл бұрын

That's sure fine metal-work. For an optimized induction-coil, the size of the hole, the wideness and the highness of the windings should be about the same, to minimize the length of the copper-wire and with it the resistant of the inductor-coil. So you'd need for every value of the inductor a different sized metal-thingy. And yes, this is a smart-ass speaking.

@homemade_audio Жыл бұрын

optimization is profitable in the case of large quantity production, but to manufacture a coil that I need with a few centimeters more it does not cause me a problem, the important thing is to manufacture it. With these machined parts I can manufacture any coil for my speakers and it does not matter to optimize either the length of the cable and resistance. In any case this video is intended for amateurs not professionals.

@furkantml 3 ай бұрын

nice video but there is a problem. does the raw material of the wire to be used matter? does using copper or aluminum change the values?

@redelala7652 5 ай бұрын

Very impressive and detailed tutorial thanks for sharing

@homemade_audio 5 ай бұрын

Thank you 👍

@BlueBeemerBoy77 Жыл бұрын

Brilliant, thanks!

@homemade_audio Жыл бұрын

You welcome 🙏

@michasy2221 7 ай бұрын

great app thanks to the engineer making this

@stevenkamala7238 Жыл бұрын

Thanks for taking your time to share this video, very great innovation and diy friendly , thanks again and be blessed for your effort and kind heart

@homemade_audio Жыл бұрын

Thank you for much for your great words, you welcome 🥰🙏

@biogesic918 8 ай бұрын

is there a specific kind of varnish to use or I can just use varnish for furnitures.. thanks

@zaqueuoliveiraalmeida8810 Жыл бұрын

Good morning friend, your video is very good, the tool is very well done... total whim! Does it make a difference to use a pcv ring in the middle of the inductor? Hug from Brazil.

@homemade_audio Жыл бұрын

yes no problem for pvc, you just have to avoid metals which can increase the inductance. You welcome 🥰

@Atheistic007 4 ай бұрын

This is why KZfaq is awesome.

@homemade_audio 4 ай бұрын

Thank you 🙏👍

@darshangoswamidarshangoswa900 Жыл бұрын

Best videos for audio work

@homemade_audio Жыл бұрын

🥰👍👍👍

@mathieupierremarceaupaulin5298 Жыл бұрын

Beau travail propre

@homemade_audio Жыл бұрын

Merci beaucoup pour votre commentaire 🙏🙏🙏 ça me fait plaisir 🥰🥰🥰

@FixitEasyDIY Жыл бұрын

Well done 👍👍

@homemade_audio Жыл бұрын

Thank you 🥰 You welcome 👍

@damiancruz2002 Ай бұрын

Impresionante trabajo, me gusta la simplicidad con la que logro una herramienta tan útil. Pregunta: sería posible que me pase los planos para enviarlos al taller de tornería para que me fabriquen una igual ? Atte. Damián Cruz

@tomicafrkovic4162 Жыл бұрын

Very nice, thanks for sharing! What is the LCR meter you use to measure coil inductance?

@homemade_audio Жыл бұрын

Hello, it's a china LCR meter called: T4 mega328. It's very cheap but very convenient specially for audio amateurs 😉

@nelsondog100 10 ай бұрын

Can we make the same measurements with a standard digital multi meter?

@mcrolabmcroab 7 ай бұрын

There is a 1.5 copper wire, how many turns are needed for 1.2 induction for a 16 ohm HF speaker? Thank you .

@sphinx7676 Жыл бұрын

Hello.. how can you test inductor MH with multimeter.. ?

@wuuu1841 7 ай бұрын

I have a question, typically, each layer should be wound in the same direction. This means if you start winding the first layer from left to right, you should also wind the second layer (and any subsequent layers) from left to right. But from your video 1. from left to right, then right to left. which is right?

@homemade_audio 7 ай бұрын

Like any other coil : If First layer .... left to right Second layer....right to left Third layer....left to right . . .

@gadiledan2098 11 ай бұрын

mantap

@homemade_audio 11 ай бұрын

🙏🙏🙏

@Manjor-qy6uo Жыл бұрын

Very Nice Pls fabricade 1 voice coil for speakers p.a 15 ichs 350/600w rms is doble impedance 8Ω/8Ω but i like more use in 4 Ω Fabricate 1 voic coil for me plss u no use nucleo Ferrite? Etc? For bass nucle air is good?

@SprinkCalSA 4 ай бұрын

Very good video. Just struggling to find the 3nd layer

@homemade_audio 4 ай бұрын

🤣👍👍👍don't leave any space between the turns and everything is fine, each layer should be tight. Good luck 👍👍👍

@vuilledeeresh4116 Жыл бұрын

Hi What happens if we don't use varnish and dont alaign the turns perfectly but still have the proper inductance.?

@miroslavmajercak9701 Жыл бұрын

Nothing, inductance is important, not design.

@carlosconde4096 Ай бұрын

I need 1.5 mh and 2.7 mh for crossover. Please tell me no. Of turns w/ gauge 20 wire

@arvindh13 Жыл бұрын

How to decide the amps? for example i need an inductor for 10amp capacity, what should i do?

@homemade_audio Жыл бұрын

Hello, the current supported by a coil depends on the section of the wire used, you'll find several tables on the Internet which show the current supported by wires.

@stevengouws8684 Жыл бұрын

Yeah the thicker the wire the higher the amps it can manage.

@davidokon2988 10 ай бұрын

Can i buy this milled parts from you ?

@carlosconde4096 Ай бұрын

Very nice tutorial!!! Can you give me data for 2.1mh gauge 20 and gauge 24.also. 35 mh gauge 24.thanks

@NiksSofa Жыл бұрын

What do you use as varnish?

@homemade_audio Жыл бұрын

Hello, it's a fast dry insulation varnish.

@jayweb702 Жыл бұрын

So what if i don't have access to a lathe? Can I get some sort of jig somewhere?

@homemade_audio Жыл бұрын

Hello, you can make them by 3d printer, or in wood, you can make any dimensions / diameters, the important thing is to enter the dimensions of your part in the calculator.

@jayweb702 Жыл бұрын

@@homemade_audio Thanks a bunch!

@stevengouws8684 Жыл бұрын

@@jayweb702 Use a stick on a drill with a bobbin on each end. Some vids available on youtube

@gregs7918 Жыл бұрын

I have made spools from PVC pipe. End flange from thin PVC flatten with a heat gun. PVC solvent glue first than add PU constructional adhesive for inner radii.

@AnanthanAnanth-rq1iq Жыл бұрын

Nice

@homemade_audio Жыл бұрын

🥰🙏🙏🙏

@AnanthanAnanth-rq1iq Жыл бұрын

@@homemade_audio number send me

@nelsondog100 10 ай бұрын

Does anybody know of coil design software for Mac?

@richardmarkham8369 5 ай бұрын

Why not wind onto a plastic bobbin?

@keijojaanimets819 3 ай бұрын

Core😁

@LakhsTsoyknikas 9 ай бұрын

now make air inductor homemade for experiments

@adnacraigo6590 Жыл бұрын

If you will cut the ends of the plastic ties flush with toenail clippers they won't be sharp and will not cut you .

@homemade_audio Жыл бұрын

😁 precision tool 😉

@nelsondog100 10 ай бұрын

Or, instead of cutting, grab the zip-tie very closely to the end while rotating the pliers in a circular motion. The result is a clean break and no sharp edge.