In this video I show how I make blackpowder for my muzzleloaders #muzzleloader #blackpowder #howto
Пікірлер: 19
@Jrabsforge4 ай бұрын
If you wanna see this black powder in action head over to @jrab3464 and see it shoot kzfaq.info/get/bejne/r-Byipmq1JymdY0.htmlsi=cmaiGURxwKGvdHuT
@richbattaglia53504 ай бұрын
Sir, you made the difference. Here I’m thinking I didn’t have enough tonnage with my press to make the pucks as dense or as hard as they should be. It was the exact opposite! I was pressing too hard which resulted in broken blackpowder pucks. Your video made the difference. Thank you again!!
@Jrabsforge4 ай бұрын
I was thinking the same thing so I got a scale recently and compared it against 777 and it may not be perfect but it's very close to the right density I believe. I have a video on it so you can see for yourself.
@johnc67383 ай бұрын
Another reason to not press too much. The more compressed the puck is the higher the ignition point will be
@bomen33021 күн бұрын
Thats why it was so hard to light with matches… thanks
@willowpine26046 күн бұрын
Not quite true that, its more the carbon source that determine the ignition point , and a tiny percentage in density (1.7cc is acceptable years now not tell almost a century). The factors that effect the ignition point quality of bp is: 1st carbon source(and all the parameters of it wich is : if its old tree or new, if its cut properly in time ,if it have bark and knobs ,if it's rotten or fresh,if its dried properly before charing, the Charing temperature etc. ), 2nd the purity of the chemicals you use, third the moisture of your end product and 4th the density! Plus if it's heavily graphited or not!
@Steven-cr8ju3 ай бұрын
My two cents: scales are typically most accurate in the middle 20% of its min/max range. Measuring a very small mass, as it appears you are, gives large accuracy fluctuations, as it appears you are experiencing, resulting in undesirable powder and lot variances. Brass ball media does not foul the powder like lead will.
@Jrabsforge3 ай бұрын
The scale is just cheap but I have a video where I shoot my powder out of a 1858 on my other channel and it groups fairly well and brass would be a good Idea I've played with alot of different media and I have those lead balls for my 1795 springfield so I just used them instead of trying somthing pricey I only thought of brass recently when seeing everything black powders new video on black powder
@roygroves23654 ай бұрын
unfortunately you didn't mix the components well enough before seperating it into two batches. You coule have more of one component in one batch than in the other.
@Jrabsforge4 ай бұрын
I mixed both batches together once it was milled so the ratios would be correct you just don't want the weight to be off balance or the tumblers will jump and the motor will heat up or they could bind somthing up etc.
@davinci32595 ай бұрын
Where did you get the sifting screens?
@Jrabsforge4 ай бұрын
On Amazon they are stackable sifting screen or mesh and alot of times are advertised as gold panning equipment
@davinci32594 ай бұрын
@@Jrabsforge thanks
@jrab34644 ай бұрын
Your welcome
@luebkeb3 ай бұрын
Lead is very conductive, what are you talking about??
@Jrabsforge3 ай бұрын
I meant to say that it won't spark I misspoke.
@luebkeb3 ай бұрын
Gotcha! Thanks
@willowpine26046 күн бұрын
You use steel in Pucking die?🤔🤔🤔 You don't afraid of any spark? If this go of the shrapnel can pass through you and your wall behind you(I'm kidding not so much but you definitely get hurt badly)!