It may not be common knowledge, but tape measures are made with the measurring "hook" on the end having intentionally slotted holes so that you can get an accurate reading when grabbing the outside of and object, as well as when butting the hook up to a flat surface as in this instance which pushes the hook against the nearer side of it's slotted holes.
@scd696911 жыл бұрын
This is not just a 30 second explanation of what the measurement is. It is a lesson in HOW TO MEASURE--the title of the video. Nothing he said was slow. I think it was necessary for him to point out what to avoid doing that could result in an inaccurate measurement. Attention to detail is crucial when measuring things. If you're going to teach someone to do something, teach them to do it right the first time.
@fcukmegently4 жыл бұрын
Lord grant him wings to get quickly to the point!
@seahunt200111 ай бұрын
Yeah, could have done that in less than 60 seconds!
@dudeling97404 жыл бұрын
The hook on most tape measures have a little play in the rivet. So that it compensates for the thickness of the hook. When you push the end of the tape to measure, the hook moves in. When you hook the the tape and pull, it moves out. Exactly the thickness of the hook. Therefore it's accurate using either method
@hndeagle7210 жыл бұрын
This guy should work for the govt. His 'change a spark plug video' must be an hour and a half long...
@familyman71483 жыл бұрын
Exactly my thoughts 👍
@daniellachance97303 жыл бұрын
Tape measure end moves according to how its used. It moves in when you butt up against object and moves out the thickness of the end when its clipped on to an object. my 2 cents
@SummitRacing11 жыл бұрын
Another way to look at it is this, if you were to cut off the portion of ruler that shows no graduations (markings) at all, this would drop the ruler deeper in the wheel during the initial measurement, effectively ADDING that 3/16” back to the graduated portion of the ruler. Thanks for commenting, we appreciate your input!
@tayseeralh9 жыл бұрын
subtract and add It should be 30 Sec show
@SummitRacing11 жыл бұрын
You add 3/16 of an inch because the measuring lines do not start at the end of the ruler, this shifts the number up and off of the mounting point of the wheel 3/16 of an inch. To compensate, you must add the 3/16s back into the measurement.
@pdiz6 ай бұрын
That dude you meet at the bar where you excuse yourself to the bathroom and leave out the backdoor... Kidding, kidding, I appreciate the video actually.
@HiMinds10 жыл бұрын
it took you 6 1/2 minutes to explain something that should have taken 30 seconds
@davidderolph28459 жыл бұрын
It all seems relevant to me. If you knew all about this, why did you watch it? He's explaining it for people who are totally unfamiliar with the concept, and I think he did a good job.
@HiMinds9 жыл бұрын
David DeRolph Really? back space, the distance between the back of the mounting face to the edge of the rim, simple as that and no i didn't know what it was thats why i looked it up
@ulissitos7 жыл бұрын
do your own video, and dont watch this...
@MrAerobill3 жыл бұрын
There's 6.30 minutes of my life I won't get back!!!!!!!!!!!!!!!!!!!!!!!!!!!
@kyferez12 жыл бұрын
You didn't cover negative backspacing... I thought backspacing was measured to the centerline of the wheel? Are there multiple ways to do it?
@peppilappu9 жыл бұрын
The comments sound like an SNL skit. Are these people for real? LMAO
@5150on42011 жыл бұрын
Seams like you really did this the hard way. PUT A FLAT EDGE ON THE INSIDE OF RIM LIP. MEASURE WITH TAPE MEASURE FROM THE THE FLAT EDGE TO THE HUB MOUNTING POINT, and your all done.
@MikeSmith-nu9wt2 жыл бұрын
Put the rim on the garage floor and measure it , unless you milling your own rims they usually only come in 6 , 6 .25 , 6.50 , 6.75 , 7.00 , so on and so forth , most dont even have 4 different widths to choose from , usually only 2 , ....jmo
@MrSnowman4276 жыл бұрын
The problem here is I don't believe you can get a rim with 7 9/16" backspace!!!
@dudeling97404 жыл бұрын
Exactly! Mine comes out 3 3/8" . But they don't offer that, only 3.5 or 2.5 , I'm trying to match an existing wheel
@norcoauctions8 жыл бұрын
did you say AXE. often axed question. you are the first white guy to say axe a question
@nukesaway480610 жыл бұрын
Dude go Metric, no fractions!
@stoneyswolf7 жыл бұрын
Good info. It gets real confusing when it's listed as offset in MM. Looking to get some 18x9 wheels that will fit my 64 chevelle it's a pain.
@vinskeeter2 жыл бұрын
Where is the part number stamped on a draglite? How can you tell the width and backspacing on a wheel with a tire, on the car? Or can you? Or, do you need to take the wheel off the car to get the B's and strip the tire off the wheel to measure the width accurately?
@kevinhlavati62852 ай бұрын
It took this guy 6 minutes to explain it wrong... I don't know about everyone else but I've always measured backspace to where the tire seats not the edge of the lip..
@TheMadShredder6 жыл бұрын
Backspacing is not problem but how do I figure out the remaining rim facing outward? Since backspacing takes into account the inner lip of rim does the difference also take account of the outer lip?
@wayneragland531111 жыл бұрын
Why not get a ruler that is "right on," instead od 3/16 in. off??
@admrlsalty11 жыл бұрын
Wouldn't you subtract the 3/16 since the the ruler will be held this much higher off the rim...
@bnut3022 жыл бұрын
Summit Racing, what is the advertised backspacing of this wheel in comparison to the actual measured backspacing?
@thomasheinonen57226 жыл бұрын
Too much redundant talk...
@samermohamed52932 жыл бұрын
Thank you so much for sharing this specially from professional 😎 I have a gmc 86 and I want to order rally wheels from summit racing but there’s two kinds of wheel back spacing 4.25 and 5 !!! Can you tell me please what should I buy for the front and back?
@samermohamed52932 жыл бұрын
15x10
@xturnitaroundx11 жыл бұрын
Lol had to think about that one for a sec too. A bigger space gives you a shorter reading so you have to add it back.
@stevelindsay36435 жыл бұрын
You have to subtract the distance the ruler started at which in this case is 3/16 on an inch. Do Not Add 3/16 You subtract it.
@abalmaintiger5 жыл бұрын
WRONG
@1960slickcraft5 ай бұрын
wrong
@joeydial55238 жыл бұрын
have a 15 x10inch rim. what would back space need to be to keep inside fender walls for a 1982 s10 truck.
@SummitRacing8 жыл бұрын
+Joey Dial , A 5.5” backspacing is the most available size that will fit but, may still have some protrusion beyond the wheel well. Much of this also depends on the tires you plan on running. Give us a call, we can help you through the process. 1-330-630-0240.
@clg_pro20092 жыл бұрын
one hes wrong its not 7 3/8ths 2nd with tire on, measure from wheel rim to straight edge and subtract that..simple!!
@stewartj34073 жыл бұрын
Just get to it buddy!
@RamonVM237 жыл бұрын
Who else fell asleep watching this gotdang video!
@digitaloverdrivesystems2 жыл бұрын
So then ask yourself, If you call Summit or Jegs or whoever, and say you want a WELD wheel with 7-9/16 back space, he will tell you they don't fuckin' make them in that increment.
@digitaloverdrivesystems Жыл бұрын
My thought exactly. Where does Summit find these HACKS to hawk there shit? Would be better off not even posting this ridiculously long, inaccurate vid...
@MassCap4 ай бұрын
15 inch rims are 16 1/4 x 7 3/4 18 inch rims are 19 1/2 x 2 This sound right? Asking for a friend
@zzsql9 жыл бұрын
zoom to 4:45 for the answer.
@Ralphieisthegreatest2 жыл бұрын
Why can't we just measure it with the tape measure?
@seahunt200111 ай бұрын
Just watch Coker Tire video. Explained in less than 60 seconds.
@andycraig77223 жыл бұрын
What is the purpose of backspacing what is the purpose of backspacing
@SummitRacing3 жыл бұрын
Backspacing will affect where the wheel is positioned in the vehicles wheel well.
@g83rboy12 жыл бұрын
who else had to watch this video like 3 times cuz you just got lost and didnt know what he just said?
@Glock274Jimmy10 жыл бұрын
For those of you who can't get past the extra space on the ruler.... think of it this way... You are subtracting the length of the ruler... (to cut off the extra portion) Therefore it creates more reading on the other end where it's measured... So both are really correct... subtracting length of the ruler... causing an addition to the actual reading. It doesn't mean anyone is dumb... People are so mean.... they think they are so smart... they probably voted for ObamaCare...
@clearraines4911 ай бұрын
Let's not over complicate this now....The don't come in 1/16ths so...dayum boy get to it
@billiebowling7755 Жыл бұрын
Spose to subtract the 3/16
@1960slickcraft5 ай бұрын
I beg to differ.
@williamb83508 жыл бұрын
I understand how you must add the 3/16 of an inch to the measurement when using the fixed ruler, but when viewing the video It looks like the yellow tape measure is at almost 8 inches. 7 and 9/16 is just over 7 and 1/2 inches (close to 7 and 8/16). Why does the yellow tape measure appear to be at almost 8 inches?
@SummitRacing8 жыл бұрын
+William Barth, Due to how quickly the speaker is moving and the angle of the camera, it is difficult to see how accurate the measurement is. When you follow the technique shown, you will be able to see more clearly the measurements you are taking.
@Jmunoz16756 жыл бұрын
Get to the point! He must get paid hourly...
@johnfair625 жыл бұрын
you took to long just to show a simple task.
@JG-dh4pe6 жыл бұрын
This could have been a 10 second video.... I think we all know how to use tape measures and rulers. Thanks for the info anyway.
@jasonparish74373 жыл бұрын
All I can say is get to the point already!
@ADayInTheLifeOfJames2 жыл бұрын
Wake me up when he finally gets to the point 😴
@crankycrow73712 жыл бұрын
This clown is telling us how to measure backspace and he don't even know how a measuring tape works .
@DadGrooves4 жыл бұрын
Holy fuck man, get on with it. 1 minute tops.
@stevendilnott4399 Жыл бұрын
off set,,, offset
@wayneanderson44992 жыл бұрын
Wholly crap..... Blah blah blah blah blah....... This video should have takin 45 secounds
@fyvosioakim32123 жыл бұрын
Drained get to the point
@loveclown810 жыл бұрын
Start at 4:45 all that before is BLAH BLAH BLAH.....
@davidderolph28459 жыл бұрын
It all seems relevant to me. If you knew all about this, why did you watch it? He's explaining it for people who are totally unfamiliar with the concept, and I think he did a good job.