HOW TO REBUILD A BARRA! Oil rings, Rod Bolts, Bearing Clearances and Piston Install

Рет қаралды 5,931

4 жыл бұрын

In today's episode of The Average Garage, We dive into the rebuild head first and throw together the short block... Starting with showing you how I installed and check the Oil Control Rings, Remove and Replace the Rod Bolts, Check the Main and Big End Bearing Clearances And finally Install the Piston Assembly's into the short block to complete it!
Thanks for watching. Don't forget to LIKE and SUBSCRIBE for more
Want to support the channel?
Head over to the Patreon page for Behind the scenes, and Early access! @ patreon.com/TAGAU
MERCH NOW AVAILABLE: www.redbubble.com/people/TAGY...
Choose a design and products available will be shown :)
FOLLOW ME on:
Instagram @ / the_average_garage
Facebook @ / theaveragegarage
Music:
Track: Abandoned & InfiNoise - Night Caller (feat. Project Nightfall) [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Abandoned & InfiNoise ...
Free Download / Stream: ncs.io/NightCallerYO
• DEAF KEV - Invincible ...
Free Download / Stream: ncs.io/defeat
• T & Sugah x NCT - Star...
• Video

Пікірлер: 23

@jimclarke1108 2 жыл бұрын

Excellent thorough work, more than i can say for many other engine builders ( with years of experience))

@T.A.G 2 жыл бұрын

cheers, i try to follow the book, aswell as try and be educational for others wanting to give it a crack

@CD-gu6kf 4 жыл бұрын

Great video and attention to detail

@tbagz89 4 жыл бұрын

Great job man. Gives me the confidence I need to build my own once I blow up my current n/a+T build lol.

@ibitconsulting4988 4 жыл бұрын

I really like your attention to detail. I like the music, your editing, Keep it up, you have a big future on KZfaq. Question are you rehoning the bores, are you going to use ARP bolts, are you putting in stronger rods? Is it worth going for aftermarket cams? I love your block prep and how you did not just paint the Welsh plugs etc so it looks better than factory. If it was me I would probably get everything balanced if I changed the rods

@T.A.G 4 жыл бұрын

Reusing factory rods, crank and pistons, replaced rings and bearings etc so no need to balance etc, The cams were all cactus so I've ordered new ones from ford as its not worth it to me to go aftermarket as I need to pass emissions testing, i have head studs ready to go and the block was honed when machined aswell as decked and prepped :)

@grantgilbert1531 4 жыл бұрын

Keep up the work on this awesome build. This has given me a lot of inspiration and has summed up what I need for my recently acquired BF Barra Engine turbo build. Cheers Man!

@T.A.G 4 жыл бұрын

Thanks mate :)

@williamfosterXD 11 ай бұрын

Might wanna add a pinned comment warning people not to send there mains at 3 thou, first video I’ve watched on your channel…. I went looking for the low oil pressure video after watching this

@T.A.G 11 ай бұрын

It's up to each person to do their own research, this is merely a guide. Every engine and circumstance is different. But yes, there was a low oil pressure vid.

@G42J3T 4 жыл бұрын

Hey mate great vids, I've never put together the rotating assembly on a motor before but arent you supposed to oil only the crank side of the bearing and not the block side of the bearing? Keep the vids coming👌

@T.A.G 4 жыл бұрын

Crank definitely. I used assembly lube between crank and bearing, and I liked between the crank bearings and block aswell but it's not needed really. I did it more so to stop any rust while it waits to be filled and fitted to the vehicle :) Hope that makes sense

@T.A.G 4 жыл бұрын

@17:40 ypull see me putting the assembly lube on the bearings. They're already in the block and main caps

@theranga3364 2 жыл бұрын

Id it necessary to measure the bearing clearance if im gonna get new main bearing?

@T.A.G 2 жыл бұрын

100% always measure

@bkfamily3098 2 жыл бұрын

Hey mate where did u get the rings from

@T.A.G 2 жыл бұрын

Atomic mate

@craigrobson630 4 жыл бұрын

Hey mate good vids, One question did you pull the oil galley plugs and oil pressure regulator valves from the block and clean the galleys. If so did you buy them genuine from ford?

@T.A.G 4 жыл бұрын

No mate. They were left I believe. Unless the machinist do it for me