#300zx #nissan #turbo In the previous video I talked about blowing the engine on my Z. This time I’m going over a few steps on how to remove the engine on my twin turbo Z.
Пікірлер: 45
@jeremythompson6822 Жыл бұрын
Man you made that look so easy😅 Meanwhile when I relocated my PTU I thought I done something 😂
@mugwhy3 ай бұрын
Nice... saved this to my playlist. Will be doing the same soon
@Pervalidus9 ай бұрын
I do this in about 2 hours in my z32. But I have a hoist in my garage. I like to remove the gearbox first with a gearboxjack then pull the engine out. Surprisingly easy when you've done it a couple of times.
@fixitish9 ай бұрын
I had to do this again it was even faster but I left the transmission in the car this time. Eventually I’ll hit that 2hr mark lol
@Pervalidus9 ай бұрын
I think it's impressive in 3 hours without a hoist! I think maybe it will be harder to wiggle the engine on to the transmission but the other way around. I did alot of deletes and moved my batteri back to my trunk. It gives alot of room to reach those two painful top bolts on the gearbox. Usually I unbolt the power steering pump and leaves it with the hoses on and just pulls it out of the way when I put the enging back in. I also pull my engine without removing the radiator as I moved to electric fan and it gives alot more clearence. @@fixitish
@fixitish9 ай бұрын
@@Pervalidus I have all the deletes done as well, I should be relocating the battery to the trunk as well but we’ll see when I actually get to it this winter. I just hope I can drive the car before it gets hot again over here.
@josesalas9061 Жыл бұрын
I am about to install an na engine this week. it was a pain in the butt to pull it out.
@gfalcone28 Жыл бұрын
Hey I'm wondering how you got that vg30dett past the steering shaft without dropping the sub-assembly? You said you were able to bypass it earlier in the video. If you could explain how you did it, it would be much appreciated.
@fixitish Жыл бұрын
I had a really crazy angle on the engine and transmission when it was coming out. It just barely missed the steering shaft. It does still get hung up on the oil pan a tiny bit but once you get there you lift up on the transmission and it gets past the rack and pinion. I’ve never had a problem taking them out without dropping the subframe only a few times with steering shaft. Only other thing I can tell you is just pay attention as it’s coming up you can slightly maneuver the engine around to get it out but I do thing the angle as it’s coming out is what really helps
@BrianRomsdal Жыл бұрын
are you in North Dakota? Looks like a ND license plate in the background. That would be cool if you were....
@fixitish Жыл бұрын
Unfortunately no 😂 im in Phoenix Az, probably a lot nicer there right now then it is here. Hot as hell
@ivansarmiento50054 ай бұрын
Which points did you use to pull your engine? And how did your v band exhaust go?
@fixitish2 ай бұрын
I usually go from the intake if I can or from the exhaust manifold. Haven’t got around to doing the v band exhaust yet still running what was on the car
@user-st4fd3nr3cАй бұрын
beast is it easier for a NA or about the same process ? Thanks
@fixitishАй бұрын
It’s about the same process with a few more steps. Not harder but definitely more work
@z32_workshop52 Жыл бұрын
J30 will be cheaper from the salvage/junk/scrap yards
@fixitish Жыл бұрын
I found a j30 pretty cheap locally at a salvage yard. I was gonna go that route and ended up finding a z32 vg even cheaper. Just hope I don’t get anymore surprises 😬
@z32_workshop52 Жыл бұрын
@@fixitish Nice, but that's surprising. most salvage yards, charge more for the 300ZX engine than the J30 Engine, even thou they are the same Engine
@fixitish Жыл бұрын
@@z32_workshop52 no your right the j30 is cheaper then the z32 vg at any salvage yard. I found this one on Facebook marketplace, running before it was pulled
@Nojalaese9 ай бұрын
@@fixitishyou’re gonna turbo the na vg?
@fixitish9 ай бұрын
@@Nojalaese yes, it already had an na vg with the twin turbo set up. It worked great but i blew it up, operator error 😆
@Alkadiem198311 ай бұрын
Did you drop the subframe?
@fixitish11 ай бұрын
No I didn’t, the oil pan does gets caught up on the steering rack so if you dropped the subframe a little bit im sure it would help clear it better.
@samogunjumo5539Ай бұрын
Started today on a driveway wish me luck
@fixitishАй бұрын
Good luck!!!
@samogunjumo5539Ай бұрын
Thanks, it’s almost out but the egr in the back keeps getting. Stuck on the firewall, any tip? I noticed you already had yours deleted
@fixitishАй бұрын
@@samogunjumo5539you can lower the subframe a bit to get some more space to get the engine out
@samogunjumo5539Ай бұрын
@@fixitish didn’t need to I got it off just needed to jack the trans a bit thanks!!!
@fixitishАй бұрын
@@samogunjumo5539hell yeah good job!!
@user-ft7pf1vl3x10 ай бұрын
5 to 6k tt engine ebay
@fixitish10 ай бұрын
After feeling the high compression n/a engine with turbos I don’t wanna go back to a stock TT engine.
@santoshernandez4573 Жыл бұрын
What are them wheels called?
@fixitish Жыл бұрын
Aohdan ds05 black vacuum
@mrvazquez153510 ай бұрын
Shit come do mine!!!😊
@fixitish10 ай бұрын
If I had more time I’d be happy to
@Defiant155 Жыл бұрын
Better get on that battery tray rust before it gets past the point of no return
@fixitish Жыл бұрын
Yeah engine is out once again to rebuild it, I’m going to be painting the engine bay so I’ll be taking care of that rust as well
@Defiant155 Жыл бұрын
@@fixitish I’d highly suggest the Eastwood Fast Etch spray. It looks costly, but can we really put a price tag on doing the job once and only once? And Raptor does have a tintable spray kit that you could get some white urethane car paint and mix to spray down your engine bay after you get everything straight and it’s a fine truck bed like spray that’ll protect. But if you go that route, don’t use Hobby Lobby paint. Was a big mistake that I made that cost me one whole bottle of mix.
@fixitish Жыл бұрын
This is going to be a whole learning process for me. I’ve always steered clear of cars that need bodywork but with this one I really want to try and do it myself. When I get to it I’m going to make sure I try and do everything right the first time
@josesalas9061 Жыл бұрын
where are you located at? I'm at phx az I'll pay you if you give me a hand.
@fixitish Жыл бұрын
Email me ish8586@gmail.com Maybe I can help you out while I’m in town