Great review my 2002 AU UTE. Fuel pump died. Mechanic. Replaced+ fuel filter.+tow. = $$783. Guess he earned it
@Hungry_Hunter5 жыл бұрын
Bloody brilliant you have just saved me spending my weekend trying to replace the pump from the bottom. Champion video and not like all the dumb Yank vids that bang on and on about how to undo bolts ect ect....
@AvgYoutubeEnjoyer75 жыл бұрын
Short and to the point, this was great! I definitely learnt a few things!
@TheCalamatron6 жыл бұрын
Very helpful, got some good ideas. Thank you for sharing your wisdom!
@peterparry61627 жыл бұрын
Many thanks for a great "how to" and easily understood.
@garylee41713 жыл бұрын
Great clip, now I can see why they charged my father in law so much to replace the sender unit in his ute.
@cheyneanderson52226 жыл бұрын
Cheers I hope it's the same for au utes!
@jackandthebeanstalk45425 жыл бұрын
Thank you very much I'm doing mine tight now liner tray and metal tray of, fingers crossed ! You have helped me. Appreciated.
@moorabinda3 жыл бұрын
Font was hard to read but otherwise a great vid. Very useful. Thanks!
@jamessmith468111 ай бұрын
Thanks Old mate! Great stuff!
@BillsBuildandRace7 жыл бұрын
Audio track re-mix to appease the music police
@shadquirk6074 жыл бұрын
rough as guts, i love it!
@bpr1543 жыл бұрын
Lol you revved the shit out of it
@greywolf2714 жыл бұрын
Very valuable, thanks. Did'nt need to depressurise the injection system, or is there another filter preventing backflow ?
@BillsBuildandRace4 жыл бұрын
Depressurising wasn't necessary.
@jaymoss92376 жыл бұрын
That was great mate cheers
@nathanhawkey81823 жыл бұрын
Great info but just to point out the B series wagon alot like the AU wagon doesn't have access panel to the pump/tank your "supposed" to drop the tank in the wagon same as the utes
@markkrawczuk19436 жыл бұрын
what about cutting a hole in the floor above the fuel tank. ? then weld some tabs on the plate you cut out and use the tabs to screw it back in place ?
@BillsBuildandRace6 жыл бұрын
If only! Unfortunately Ford designed the chassis so you can't do that. There is a main cross member that goes right over the top of where the access hole is to the petrol, so if you cut a hole in your floor that's all you'd see. Clever.
@raymondstone96365 жыл бұрын
Agree. But I would be very wary of welding near the fuel tank. Might go kaboom.
@NightlifeReALIty3 жыл бұрын
Legend
@johnevans4812 жыл бұрын
Is the 99 au ute the same? With the single overhead before the barra?
@BillsBuildandRace2 жыл бұрын
I don't know.
@ahmedtouck89134 жыл бұрын
So ba falcon ute requires a longer fuel pump rather then the shorter 1, im currently replacing mine
@nharvey94254 жыл бұрын
Why didn't Ford just have a removable cover plate through the tray bottom? Too hard to work out?
@NightlifeReALIty3 жыл бұрын
Because then mechanics wouldn’t have a way of charging high labour costs
@user-oc6wi3tg1h Жыл бұрын
讚,謝謝分享!
@sheriethomas99317 жыл бұрын
Where were you living in 2013 ? 6:21 Somewhere around Newcastle I would assume .
@BillsBuildandRace7 жыл бұрын
Yes - at Maryland.
@Xanderscotty1993 жыл бұрын
How did you remove the sports bar
@simonward65594 жыл бұрын
Hey bro how did you manage to get the pump assembly unclipped im trying to do my pump atm and the thing wont come undone
@kym3934 жыл бұрын
2 small push in tabs on both sides
@milkyway67246 жыл бұрын
nice-ty
@adventuresofleah12712 жыл бұрын
The Tub should have had an access panel from the floor to open and removed the fuel pump
@BillsBuildandRace2 жыл бұрын
Unfortunately that does not work, as the fuel pump is not only under the ute tray floor, but under a chassis cross member as well. Crap design!
@gfam2023 Жыл бұрын
What if I have a tow bar, do I have to remove it first
@BillsBuildandRace Жыл бұрын
No Gman
@wescadmore38314 жыл бұрын
How do you undo do and redo the fuel lines to the pump. ?
@BillsBuildandRace4 жыл бұрын
Yeah they are devious little critters, aren't they. And you're worrying you'll beak them. They have a clip inside the neck of the plastic fitting that has two tabs on it that lock over a lip on the metal fuel line. You insert a small flat bladed screw driver parrallel to the fuel line & up against it into the fitting to raise the lock clip insert ends out, From memory you can do them one at a time - or maybe you have to do both at once if my forget-ry is working overtime. Then you can pull the line off. The fitting just slides back on & clip locks in place when you are finished.
@michaelnewton14062 жыл бұрын
or buy a cab chassis with an alloy tray
@motow30312 жыл бұрын
Hey Bill do U have a product link.
@BillsBuildandRace2 жыл бұрын
Not sure what you mean by "product: moto, but there are Facebook links to me on this channel's home page if you want to chat.
@solidbloke7 жыл бұрын
did mine last weekend. my tank doesnt have the mold like yours did so i could just drop it down
@renwickfonceca75525 жыл бұрын
Where is the cut off switch for ford falcon futura ba located?
@BillsBuildandRace5 жыл бұрын
Dunno. Best try the BA Falcon Facebook forum.
@nathanhansford765 жыл бұрын
Left hand footwell, under the kick trim and carpet, right forward against the firewall.
@tarzan3867 жыл бұрын
looks like the donated fuel was from a "flood victim" possible...cant believe how dirty this was...run the car with some e10 to clean the system also these cars are ok using this..and imagine your injectors and fuel system
@yamaha2bangas7 жыл бұрын
Came here for the music wasnt dissapointed. Didnt learn anything though
@bonz35805 жыл бұрын
Are you to remove the rear quarter panels easily?
@paulthompson72984 жыл бұрын
Don’t you hate searching the information required for a job on the car only to find one blow hard after another more interested tooting their own horn instead of offering any useful information
@kevinhynes92275 жыл бұрын
is it the same way for a 2002 au 111
@BillsBuildandRace5 жыл бұрын
Can't see why it wouldn't be identical... and I've wrecked both.
@kevinhynes92275 жыл бұрын
yes mate it was identical but i went around it another way but thanks
@skezburah Жыл бұрын
Shit that's annoying.....my ba ute needs the gauge sender changed ....so I'll have to do all of that...great
@NinjaLifeCrisis2 жыл бұрын
The FG is way easier. I jacked the car right up on stands, then dropped the tank from underneath. I put a Walbro 525 in it. No disrespect but that seem to be a lot harder than the FG.
@BillsBuildandRace2 жыл бұрын
No disrespect felt, as Ford changed their design between those models. The BA ute was a car they just stuffed up with that plastic fuel tank having a non-removable neck, and the chassis having a cross member going right over the top of the fuel pump access point. Their mistake - not mine!
@NinjaLifeCrisis2 жыл бұрын
@@BillsBuildandRace Cheers Bill.
@ufowraith2 жыл бұрын
Hmm the bloody territory has no access hole under the dam seat either 😡 So hopefully there's no chassis cross member in the way because ill be cutting my own frigen access hole😡
@BillsBuildandRace2 жыл бұрын
kzfaq.info/get/bejne/bq11rMSonMuzgqs.html
@theblade664 жыл бұрын
Great video but 100% shit design why would they make it that hard to access the fuel pump. That's just ridiculous.
@Themunz20162 жыл бұрын
The process to access the pump assembly in those utes are to drop the tank from the bottom via tail shaft removal and unbolting the axl and pushing pack on the leaf springs. I did the same this guy did on my Ute after the return hose had a broken clip from a mechanic upgrading my fuel pump.