Hey mate, awesome video!!!! just wish i could have found it easier! I tried searchin TDCI and 2007 and then found this and its almost identical and gives me SO MUCH INSIGHT that i wouldnt have had without this video. THANKS FOR TAKING THE TIME TO MAKE IT!!!
@ALLTHINGSJIM6 жыл бұрын
Pete Hines thanks for the kind comments, glad I could help 👍👍👍👍
@gheorghebogdaniuc50123 жыл бұрын
@@ALLTHINGSJIM a)
@dangleason90235 жыл бұрын
I ordered my master cylinder after discovering a leak from where the clutch pedal meets its pivot point. This is the best video i've found to help replace it, even if it is still pictures and a right hand drive. I'm in the US. But this should be able to guide me for this repair. I might make my own video, we'll see. If I do make a video I'd like to leave a link in these comments for others if they are going through what i'm going through.
@ghilashamaili2733 Жыл бұрын
Kuddos for mentioning that little seal! It can cause a huge problem! When you dont even notice it in disassembly and lose it.
@davidbuchanan33746 жыл бұрын
Most awkward job i think ive ever tackled... Never lost so much skin in my life lol.. Excellent video, thank you for posting..🍀👍
@Jonny05modesto6 жыл бұрын
David Buchanan Hey which car did you change it on? I was quoted $1049.00 dollars. I'm hoping to do myself!! 2013 focus st
@davidbuchanan33746 жыл бұрын
Jonathan Akers Its a 2005 duratec mk2 2.0 16v 140bhp chain driven cam.
@franciesruber68813 жыл бұрын
You're channel is very helpful source of information, 1 of the best on this utube.....i just did mine and saved me a tone of cash at the mechanic, cheese from Australia down under
@ALLTHINGSJIM3 жыл бұрын
Thanks! Glad it helped, thanks for watching and commenting 👍
@DraculaSWBF28 ай бұрын
You may want to specify British. Looks like I have to remove the battery and the air filter box as well.
@dieselhead242 жыл бұрын
Thanks for the video Jim, it gave me the confidence and knowdledge to attempt this job. Don't think you need to remove those scuttles. Maybe it makes access a little easier, but not much. Master cyl; twist to the right to remove (viewed from pipe end). You can see the little ramps which facilitate insertion. I lubed my new one with a bit of fairy liquid which helped it slip in nice and easy :)
@theashtreecollection2 жыл бұрын
Really helpful video just done the master cylinder on my wifes car this video was so helpful thank you for posting.
@simonocallaghan51854 жыл бұрын
Great video Thanks mate! Just about to tackle one at work and was hoping for a quick twist out job lol how wrong I was! At least now a know what must be done. 👍
@ahmedtouck89134 жыл бұрын
Hi you made it look easy unbolting it. I did the same way, only to hit the safety bar behind the dashboard, ..
@fritslentze97664 жыл бұрын
Just loved your video. It gave me a lot of insite, and did, indeed decrease my stress-level. THANKS JIM !!
@leftwolftv667 ай бұрын
i have a 2016 ford focus manual transmission with the 1.0 ltr ecoboost engine,,my clutch pedal doesnt move up,,and the mechanic i brought it to said he has to remove the transmission to replace the master cylinder,,is he right?
@GeezerEnduro5 жыл бұрын
This causes clutch pedal to stick? Sometimes to the floor!? Ford obviously knew about this which is why they made a metal replacement. Why has there been no recall on this. This is a massive safety issue.
@ALLTHINGSJIM5 жыл бұрын
Yeah, and I have no idea tbh!
@paulnolan11132 жыл бұрын
My Volvo s40 is doing this pedal on the floor might try this ..
@sharoonzaib82556 жыл бұрын
nice job can i watch the full video i have 2005 reg mk2 ford focus
@miroslavb.7309 Жыл бұрын
very complex exchange. Does brake fluid also go for the clutch pedal?
@garetharendse40017 ай бұрын
Hi, like the video, struggling to get clutch master cylinder in the slot?
@frundlemud11 ай бұрын
Very helpful the best I've watched.
@ALLTHINGSJIM11 ай бұрын
Glad it was helpful!
@matytoycars64013 жыл бұрын
Hy. Thanks for the video. It was very usefull. Now i m at the second intervention that was looking good until restart. Now i have 2 errors: tire sensor error+parking aid sensor error and also wont unlock the steering column. Do You have Any idea what i ve done wrong?
@mechtechmechanical15714 жыл бұрын
hi Jim great info ,Im replacing the master cylinder on my focus but there is additional sensor at the other end of the master cylinder engine side any ideas what this does cheers
@ALLTHINGSJIM4 жыл бұрын
I probably would if I could see it aha. Where exactly is it fitted? On the master cylinder itself or a pipe?
@mechtechmechanical15714 жыл бұрын
Hi Jim on the master cylinder itself it clips to the side has a square block connector think it might be clutch position sensor
@ALLTHINGSJIM4 жыл бұрын
Yeah most likley 👍
@MuLTixsHo72 жыл бұрын
My focus has a very hard pedal and it feels like the clutch comes out very slowly, could that be the cause?
@imadidrissikhamlichi52652 жыл бұрын
I got Clutch position sensor A circuit high code p0808. All sensors are plugged in. Any suggestion how to fix ?
@truevizard5 жыл бұрын
Currently have this issue. Damn, looks like a more serious job than I thought :(
@Adam-zt7gb2 жыл бұрын
Great video, everything exactly as described. I just can’t seem to get the pedal out, I’ve tried twisting turning wiggling, just about everything. Is there a certain movement or direction you found worked best?
@ssss-df5qz Жыл бұрын
He was just extremely lucky. Best bet is to just make enough space to get some pump pliers on the cylinder to rotate it and squeeze it out between the bulkhead and pedal box.
@Drifter5696 Жыл бұрын
Since clutch master cylinder and brakes uses the same fluid. Do I have to bleed brakes too after I pour all the brake fluid from the reservoir?
@ALLTHINGSJIM Жыл бұрын
If youve drained is soley from sucking it out the clutch feed pipe and left the rest of the brake fluid in the reservoir then no, if youve sucked all the fluid completely out of the reservoir so its bone dry its probably best to even though there will still be fluid in the brake lines. 👍
@Adam7H3 жыл бұрын
Hello thanks for making this video, do you know where I can get that metal push rod replacement from? Thanks
@ALLTHINGSJIM2 жыл бұрын
Any main dealers as its a superseeded part, you might find one on ebay or a automotive parts supplier too
@ZIZUU3 жыл бұрын
When I press the clutch pedal it squeaks. What should I replace? Car: Focus Mk3, 1.0 EcoBoost.
@fastlanekang3 жыл бұрын
Mine squeaks too and after checking it my clutch master cylinder is leaking brake fluid and it runs onto the rubber spring cover causing it to squeak. Dealership price for entire assembly was only 114.00 with tax
@Sergiu_K4 жыл бұрын
Did you remove the steering wheel column for this? It is not mentioned as a step so I would suspect not? Why was the connection to the steering rack removed?
@ALLTHINGSJIM4 жыл бұрын
No the column wasnt removed, the lower column was disconnected from the rack as shown because otherwise you dont have enough room to pull out the pedal assembly 👍
@ChristophePERRINLyon5 жыл бұрын
Thank you for this great video ! Can you confirm that they are 2 clutch pedal sensors/switches ? I think that one of mines not working (no more Start&Stop), so I've checked the first (in your video), easy to remove and working fine, but didn't see the second (top sensor) because it's more difficult to acces.
@ALLTHINGSJIM5 жыл бұрын
If your stop start has stopped working you might want to charge your cars battery , stop start will stop working once the battery charge level drops below 70% once its charged test it again, you may need to get it re activated if it doesnt start working after a few engine cycles too. I say all this as most peoples stop start problems I ever have as due to a discharged battery
@ChristophePERRINLyon5 жыл бұрын
@@ALLTHINGSJIM Thank you for your answer ! I've checked the both sensors, and they're working fine, so It's probably the battery, nearly 8 years old, so it's time to change it.
@m1rchegfn4 жыл бұрын
I changed the complete clutch and flywheel set on Focus MK2 1.4 petrol, but the pedal started to get heavy. We bleeded the liquid, but sometimes the clutch pedal is really hard, other times it is not. Probably the master cylinder needs changing also?
@ALLTHINGSJIM4 жыл бұрын
Was it like it before? I had one a couple of months ago where the new slave cylinder that came with a gearbox was faulty and went hard then popped, replaced it under parts warrenty again and was fine after, could just be a dodgy part...
@m1rchegfn4 жыл бұрын
ALL THINGS JIM no. The thing is, when I do a hard acceleration or hard brake, the clutch pedal is soft a few times, after that it hardens. Really weird. I suspect the master or slave cylinder.
@ALLTHINGSJIM4 жыл бұрын
Have you checked your servo vaccum line isnt damaged or disconnected?
@m1rchegfn4 жыл бұрын
@@ALLTHINGSJIM I am not sure. I know that I went back to the shop after the clutch change and they sucked the air out and I was pressing on the clutch at that time, but still the clutch pedal didn't become soft as I would like it to be.
@mikekeenam30143 ай бұрын
I've got Mark 3 focus 1.6tdci . I have clunking noise when changing gears mainly 2nd and 3rd, 4th. Mechanic said needs new clutch and flywheel which he did. But noise still there and seems worse than before. Also changed the master cylinder as said didn't like the pedal feel. Any ideas why have clunking noise?
@oyumerov5726 Жыл бұрын
Thank you a lot!
@Inthe_bin4 жыл бұрын
Ive changed this on mine and my car wont rev past 3.5k rpm when stationary so thinking its one of the 3 sensors, what does each sensor do.. 2 inside the car and the sensor on the master cylinder?
@joeymcdaniel11043 жыл бұрын
When in park your car is factory tuned to not allow you to rev past 3.5k rpm nothing to do with the sensors.
@bathy852 жыл бұрын
cruise control minor
@truckeraaron9923 жыл бұрын
Do you have a part number or when I can get one with the metal bit on only ones I find online are plastic
@ALLTHINGSJIM3 жыл бұрын
Sorry I dont but if you pop into or call any ford main dealers parts department they would be able to give you it 👍
@carlosortiz6742 Жыл бұрын
Would a symptom be brake fluid leaking on your clutch pedal?
@ALLTHINGSJIM Жыл бұрын
Yes 👍
@carlosortiz6742 Жыл бұрын
@@ALLTHINGSJIM Thank you for the content. Changed my daughter's clutch master cylinder couple days ago, such a tight space to get to. Which made it physically taxing. We got it done though.
@JackTuned5 жыл бұрын
Anyone know if this is the basically the same procedure for a 2011 fiesta?
@michaeltaylor11494 жыл бұрын
Anyone lol? I am leaking fluid out to the point i cant go into any gear i thnk its the master cyclinder.
@enthuzst61433 жыл бұрын
I posted this on the focus st forums, i replaced my master cylinder, put everything back together, checked it four times before putting battery back in and my car won’t start when pressing the clutch but does start when pressing the brakes, any clue on how or why this is happening?
@ALLTHINGSJIM3 жыл бұрын
Did your unplug and forget to plug the clutch pedal sensor back in?
@enthuzst61433 жыл бұрын
@@ALLTHINGSJIM It’s plugged in
@ALLTHINGSJIM3 жыл бұрын
Ok, unplug it and if i remember right its a 2 pin plug, get a paperclip and bridge them and press start button, if it starts then your clutch switch is now faulty ( dont leave the paperclip in after this, its a test to diagnose that sensor not ment as a repair)
@ALLTHINGSJIM3 жыл бұрын
Or use a test lamp / multimeter if you have the knowlege to use them and see if theres voltage to the wires first before and after pressing the clutch switch
@enthuzst61433 жыл бұрын
@@ALLTHINGSJIM thanks, both switches were fried just ordered them from the dealership
@robinwas-miles96863 жыл бұрын
Seriously long and fiddly process that must take alot of time. According to our local garage in Bristol, we have just had a new "slave cylinder" put in for £140. Took a non-Ford pro about two hours. Money well spent and not a ton of cash when the part is sold for about £35 to £45 incl vat. PS: The master cylinder was done 6 months earlier at a cost of around £200 - £240. Small Ford Ka mk 2 cars can give you big head-aches.
@samehsaad1596 жыл бұрын
I had mazda zoom 3 2005 manule From where i can get one with steel arm i replace it 2 times withen 3 years and the origenal one has a plastic arm?
@ALLTHINGSJIM6 жыл бұрын
Sameh Saad im not too sure about getting the part for a mazda, but the ford one i use in video is a main dealer part, ford knew it was a problem with them snapping so they modified the arm to a metal one instead of plastic
@basmdaka69544 жыл бұрын
How long is the job
@ALLTHINGSJIM4 жыл бұрын
Depends on your skill level, id recommend atleast 2 hours
@enthuzst61433 жыл бұрын
2:37 loosen it or lose it?
@Roollaayy Жыл бұрын
how many hours and labour Cost on average ? my pedal needs replacing 🙄🙄🙄🙄
@ALLTHINGSJIM Жыл бұрын
Labour cost really depends on where you go and what area, in a main dealers expect to pay £100+ a hour, labour time is around 2 hours I believe 👍
@GalMk4 жыл бұрын
Hi Guys, should i put any type of grease anywhere on the shaft or tip? Heard it’s a must in this procedure but haven’t really understood where exactly to grease it
@ALLTHINGSJIM4 жыл бұрын
No dont grease it at all. They arnt designed to have grease on them 👍
@garetharendse40017 ай бұрын
I have a ford focus 2016 1l
@lozanospain12 жыл бұрын
Great video,thanks for share 1 subscriber + ✓.
@wp87863 жыл бұрын
I could have done without the music and you could have explain shit better then wrtting it down. But thank you anyways.
@ssss-df5qz Жыл бұрын
This is a pig of a job. If it wasn't for the seal plate integrated into the cylinder, it would undo and come out through the bulkhead in the engine bay. Absolutely the worst design.