How to Replace a CV Axle in Your Car

Рет қаралды 1,535,658

12 жыл бұрын

CV axle replacement. How to replace a CV axle in your car, DIY with Scotty Kilmer. How to remove CV axle. If the CV joint is clacking as you accelerate and turn at the same time, you need a new axle. DIY car repair with Scotty Kilmer, an auto mechanic for the last 44 years.
⬇️Things I used in this video:
1. Tie Rod Remover Tool: amzn.to/2kqdAke
2. Sledge Hammer: amzn.to/2iasnep
3. Tie Rod Seperator: amzn.to/2ipRBWr
4. Grease: amzn.to/2AVVTzD
5. Metal Oil Pan: amzn.to/2nlDM0y
6. Seal Puller: amzn.to/2ACZyl4
7. Hand Pump: amzn.to/2iZ88V1
8. Ratchet and socket set: amzn.to/2inoxOY
9. Mechanic’s Tool Set: amzn.to/2Bzmccg
10. Shop Towels: amzn.to/2jGDfkA
11. Disposable Gloves: amzn.to/2zSRuxO
12. Steel Jack: amzn.to/2Asgjxo
13. Jack Stand: amzn.to/2jGOwBg
14. Common Sense
15. Full HD Camera: amzn.to/2AvoEk7
16. My computer for editing / uploading: amzn.to/2i2sKYz
17. Video editing software: amzn.to/2jv5Fhf
18. Thumbnail software: amzn.to/2k7tz6C
🛠Check out my Garage to see what I use every day and highly recommend:
www.amazon.com/shop/scottykilmer
❗️Check out the Scotty store:
goo.gl/RwhRGU
👉Follow me on Instagram for the latest news, funnies, and exclusive info / pics:
goo.gl/ohy2cA
If you liked this video, consider subscribing and press the bell Icon to get updated on the latest videos every week.
And remember, every day (7 days a week), I upload a new video on the Scotty Kilmer Channel: / scottykilmer
Also, if you like my car help, be sure to watch my live car talk show, every Thursday afternoon at 1 CST and Saturday morning at 10 AM CST on KZfaq. I answer your car questions LIVE there. Just check it out at: • Video
Scotty Kilmer is a participant in the Amazon Influencer Program.
#savagescotty

Пікірлер: 1 500

@scottykilmer 6 жыл бұрын

Things I used in this video: 1. Tie Rod Remover Tool: amzn.to/2kqdAke 2. Sledge Hammer: amzn.to/2iasnep 3. Tie Rod Seperator: amzn.to/2ipRBWr 4. Grease: amzn.to/2AVVTzD 5. Metal Oil Pan: amzn.to/2nlDM0y 6. Seal Puller: amzn.to/2ACZyl4 7. Hand Pump: amzn.to/2iZ88V1 8. Ratchet and socket set: amzn.to/2inoxOY 9. Mechanic’s Tool Set: amzn.to/2Bzmccg 10. Shop Towels: amzn.to/2jGDfkA 11. Disposable Gloves: amzn.to/2zSRuxO 12. Steel Jack: amzn.to/2Asgjxo 13. Jack Stand: amzn.to/2jGOwBg 14. Common Sense 15. Full HD Camera: amzn.to/2AvoEk7 16. My computer for editing / uploading: amzn.to/2i2sKYz 17. Video editing software: amzn.to/2jv5Fhf 18. Thumbnail software: amzn.to/2k7tz6C 🛠Check out my Garage to see what I use every day and highly recommend: www.amazon.com/shop/scottykilmer ❗️Check out the Scotty store: goo.gl/RwhRGU 👉Follow me on Instagram for the latest news, funnies, and exclusive info / pics: goo.gl/ohy2cA

@lightninglashx9332 6 жыл бұрын

Scotty Kilmer I'm wondering should my cv shaft have slight bit of in and out play on both sides I own a 98 hyundai excel I don't get any noise besides a creek noise if I take of harder then creeping from a stop. But I think that's just my tie rod and ball joint that I know are bad. Thanks

@sumbl1ss 6 жыл бұрын

Sooo great. But what’s that “special puller” ?!?

@johnnyclean8233 6 жыл бұрын

Scotty Kilmer lol you make it look so easy. 😁👍

@S4iF_KING 5 жыл бұрын

Once i change it. Should i have my car tracking done

@donaldgrappo4526 5 жыл бұрын

Scotty:You are wise and inspirational. And you are great teacher. And May God bless you.... Merry Christmas and Happy New Year! Yours truly, Don

@scottykilmer 11 жыл бұрын

I never torque em, I just put em on super tight using hand tools, never had one fall off on me either. You'd need a manual for torque specs if you want to do that, me, I wouldn't bother, just get em tight

@DRNeKky 3 жыл бұрын

My CV axle won't go in even after hitting it with a hammer for 20 minutes. What am I doing wrong. The snap ring is in the middle. Didn't shift down. Still won't go in all the way. It's actually sticking out like 1 Centimeters or so. Thanks

@DaDaDo661 3 жыл бұрын

@@DRNeKky Try twisting it around a bit. You need to get lucky. Are you still having the issue?

@Unibot47 3 жыл бұрын

@@DRNeKky Legend has it he's still hammering that axle to this day.

@One21P 3 жыл бұрын

FYI Scotty's strength is the torque spec.

@jwrn4u 2 жыл бұрын

I use your “ tighten to one uhhh rule all the time “

@TheLe016 7 жыл бұрын

Thank you for what you do Scotty! Just changed my CV axle on my truck by myself. I never had anybody teach me how to work on my own vehicle growing up, I'm glad KZfaq can bring me close to the experienced ones such as yourself. Thanks again!

@Unibot47 4 жыл бұрын

That's awesome. How was it? As easy as Scotty made it look? lol I need a new axle and have never done repairs before.

@ahmadzain8361 4 жыл бұрын

yes

@abdullahalhamduni8954 4 жыл бұрын

I did today same way with the grease and its work for 10 minutes and the cv axle popped out after one mile and start leaking transmission fluid

@moisesr7840 4 жыл бұрын

Did you use all the tools he mentioned?

@mq5731 3 жыл бұрын

Disclaimer: Scotty doesn't show some of the efforts that goes into removing some of this stuff and makes it look a lot easier than it is.

@brianpalmer4280 6 жыл бұрын

Fastest subscribe ever. This guy is perfectly clear with his instruction, the video is just where it needs to be, he doesn't over complicate, or drag things out. PLUS he links everything he used. This is some A+ content.

@sanBastian123 10 жыл бұрын

I did my cv joint replacement with this clip. Scotty makes it all looks so easy. Minor obstacles were opening nuts here and theret, but the bare essentials are all in in this tutorial. Save me a big bucks. serious.

@rockbay79 12 жыл бұрын

Scotty, you make every job look really easy. A sign of a real professional. I'm getting too old and cripple to work on cars anymore, but your videos help me to know what repairs may be needed down the road. Thanks for sharing and keep up the good work!

@scottykilmer 12 жыл бұрын

often, you remove the axle shaft from the inner cv joint, then get a puller to yank the joint out of the transmission. I use a slide hammer and a puller adaptor in such cases. It always works with a little modification and grinding if necessary to make em fit on.

@LuisRamirez-ln3cj 5 жыл бұрын

Thanks, Scotty. With so many DIY car repair videos, I'm glad we can always count on having at least one reliable, accurate and honest source of information. You rock.

@joschmo3223 9 жыл бұрын

Scotty, Your videos are great - I normally hate watching repair tutorials because of slow progress through the steps, but you know how to masterfully edit down to just what's needed. I also love the energy - "just remove these bolts here, UNH! And tap this out here, UNH!" Now I know I'm not alone, grunting away at wrenches.

@briansmobile1 12 жыл бұрын

Excellent work in providing details AND keeping it concise. You have a real talent there. Way to go!

@TheOgAutisticOne 2 жыл бұрын

this guy helped me on my homework

@nextari 8 жыл бұрын

You, Sir, are awesome. First time viewer; this is the best car maintenance video I've ever seen by 1000x, and not a single second wasted. Subscribed. Thank You!!

@johnclassen604 7 жыл бұрын

i love how he has a very short and fun intro then gets right to the point of the vid. with quick easy instructions. thanks scotty keep it up!

@scottykilmer 10 жыл бұрын

If you wish to ask me car questions, I am switching my questions and answers to my google+ community “Auto Repair With Scotty Kilmer”. So please, if you want your questions answered, go to the google+ community and type my community name in the search and join, it’s free. Once joined, you can ask questions right there.

@nigelio3 6 жыл бұрын

"Then you tighten that up...UGH!" Classic Scotty. Love it.

@humbertocastro2020 10 жыл бұрын

Pickle fork on the in board compression C clip is genius, I was having trouble, came in to see how you do it and POW! Thanks a lot Scotty.

@prodog7761 4 жыл бұрын

My axle is stuck i guesd i need a fork tool

@scottykilmer 11 жыл бұрын

you can also remove the upper ball joint and take it off that way. If your lower is stuck, it may need breaking off with a torch and replacement

@mykeroark2892 3 жыл бұрын

I'm capable of learning most things easily with proper direction. I'm by no means a mechanic, I'm a landscaper. Your video helped me replace my CV axle with no experience. Baby's running smoother than ever. Thanks!!!

@balabay77 8 жыл бұрын

Dang Scotty, you make awesome videos. Short, sweet and straight to the point. Keep up the good work sir. Cheers

@scottykilmer 11 жыл бұрын

it's a good idea to change the seals when the axle is removed, they are pretty cheap and do wear out over time

@chupokabra228 8 ай бұрын

Is there a gasket on right passenger side with longer cv axle?

@z650_jonah5 7 жыл бұрын

you make it look so easy lol, I had to make 3 trips to a parts store to get the right size socket for the axle. 1 1/2 inch was slightly to big and 33mm was a little to small. $20 in returned sockets later i was able to get it out and finished. Thanks for the video Scotty, you have helped me on numerous occasions. much appreciated. have a awesome day.

@jonasgrumby1093 6 жыл бұрын

1) The torque specs on all those nuts are: one grunt 2) now the car needs an alignment since you took it apart at the strut instead of the lower ball joint

@ameliaroque3854 5 жыл бұрын

VITO SCOTTI - ah, thank you grasshopper.

@levigallion776 5 жыл бұрын

What?

@garynair5143 5 жыл бұрын

Not if the strut bolts are straight . There is no alignment change for that.

@freerunnersunion_________90 4 жыл бұрын

@@garynair5143 Its always best to get alignment anytime you do front end work imo, especially since manydont do them often enough.

@garynair5143 4 жыл бұрын

@@freerunnersunion_________90 if your tires aren't showing signs of alignment wear and your steering is straight before the alignment then redoing an alignment especially if none of the parts caused any change in previous alignment will show what ?

@scottykilmer 11 жыл бұрын

yes, I often remove lower ball joints to get room to remove an axle

@Ryyobrow 6 жыл бұрын

Just break the axle nut with one arm while sitting down. Easy as that boys.

@Eggsr2bcrushed 5 жыл бұрын

He's just that strong...

@jeffreymeeks4051 5 жыл бұрын

Make sure to add an extra "Umph!" To show intended physical strain.

@bettyduncan8465 5 жыл бұрын

Well, loosening things up before making the video makes more sense than forcing people to sit through 5 or 10 full minutes of grunting and screwing around with seized nuts and bolts. I'm glad it was edited to under 5 mins for the whole thing. Anyone planning on doing this should be somewhat experienced anyway. If not, this shouldn't be your first project.

@davidcraig9540 5 жыл бұрын

Hahaha it took me hours and I broke multiple sockets

@RzVids 4 жыл бұрын

Betty Duncan I’d rather see 20 minutes of struggle than to see it loosened up so I know exactly what to expect when I do it myself especially if it’s not the same car... and no one is forcing you to watch it/watch the entire thing. If you are somewhat experienced, simply skip throughout the video, but this is a very poorly informed instructional repair. What happens if you can’t get the axle nut off? You’re stuck. What happens if you tighten the axle nut like the way Scotty did? Those axle nuts are anywhere from 100-300 ft of torque...

@campeye1 8 жыл бұрын

Scotty, nicely done. I watched several videos on this before catching yours. Wish I saw yours first. Smacking it in to get the clip to engage, your the only guy that thought to mention that and to prepare for fluid loss. Attention to detail dude, you're the man!

@BigD1395 6 жыл бұрын

I've been watching you vids for quite some time Scotty, not because I have to I've been a mechanic now for over 25+years. I just enjoy your enthusiasm when you make a vid. Keep up the comical work bud. 2 thumbs up.

@scottykilmer 6 жыл бұрын

+BigD1395 thanks for watching 👍

@rodm5830 5 жыл бұрын

Seriously I love how you don't waste any time with needless jibber jabber and don't have some mindless obnoxious music playing. Thanks for making all these videos.

@JMGOcrazy7 9 жыл бұрын

Thanks for the video , this video answered all of my questions . Thanks for all of the details. I recently lost a ball joint on my f150 and the cv axel came out too. I was afraid I was going to spend a ton of money in taking it to a shop but thanks to you I know I can do it myself

@erroldillon1548 7 жыл бұрын

Scotty, you're a Bad Boy!!! You're probably the best car guy on KZfaq. I've watched a lot of people talk about mechanics in my lifetime and I really think you're the Bottom Line! Thanks for all of your fantastic videos. I would be in trouble without you! I just took the nut off my 96 Infiniti with a Milwaukee 1/2" impact wrench and boy was it easy. I think everyone needs the Milwaukee 1/2" & 3/8" impact wrenches. They make life so easy doing this job. I tried to take the 36mm axle nut off with my 1/2" Mac air impact wrench and it was like "can this tool do this". The Milwaukee cordless impact tools are really fantastic. I know most people can't afford them and neither could I. I bought one piece at a time when I bought the Milwaukee tools. They are worth their weight in Gold. All of the nuts and bolts just fly off. Thanks again for your fantastic tutorials. Every time I get ready to do a job I go to guess who, "Scotty Kilmer". The Bottom Line! I know you have the air tools and could have done this job with them. You have to show people that air tools aren't necessary. The average person is looking for a simple way to do this job. And you showed them exactly what they needed to know.

@desnowboarder 5 жыл бұрын

Scotty, been watching your videos for a couple years now and I love them. One piece of positive criticism. Show us how to getting the replacement part at the auto parts store. I have learned not to trust the person behind the counter. Show us how to assure the correct part is purchased. Also how to research a part correctly. Different engine options in the same care can be confusing. Also how to tell if a part will fit many different years of a model. Stuff like that. The people watching your videos more than likely dont k ow this stuff if they dont k ow how to change the parts you are showing. Thanks scotty love ya sir!!!

@scottykilmer 11 жыл бұрын

you save a ton doing it yourself, no parts mark up, no labor

@DavidJohnson-ex3fu 3 жыл бұрын

Hey Scotty I ran into a situation where I put both my CV axles in, without using the big hammer. I'm having that issue with my outer right side axle on my Saturn Ion Redline. I had to go back to your video to see where I was screwing up, I never hammered the axle in so I ordered a 3lb hammer it will be here tomorrow. Otherwise I shift his car into gear and it don't go nowhere! Thank you for being there for us all, even us backyard mechanics who have been working on cars for years, we have to catch up with the times and we have Scotty to help us along the way

@jedediahbc 5 жыл бұрын

Thanks Scott you make it look as easy as heck, well I done a cv axle a little over 20 years ago, so I'm going to try it again on a Honda. Thank you for your very informative videos.

@scottykilmer 12 жыл бұрын

as I've already said , it was changed 2 months ago during a clutch job.

@scottykilmer 11 жыл бұрын

son is on the 101st airborne, chief engineer/machine gunner.

@christianramirez3311 4 жыл бұрын

You are the coolest skilled tradesman ever...thanks for sharing...helps the back yard mechanic like myself that much more informed

@charleswilliams9369 5 жыл бұрын

Scotty, this video helped give me the confidence to do it myself! 2007 Yaris, same idea, wack it at the right place and came out. Couldn't believe it! Thank you!

@scottykilmer 11 жыл бұрын

it's hell attempting to fix one on the car, AND realize they make brand new axle assemblies in china that cost about 50 bucks so you just replace the whole axle as a unit. I never fix em anymore because of this, just replace them

@joeserrano378 2 жыл бұрын

Master scotty you are my hero thank you so much for helping the community

@fed9096 2 жыл бұрын

and that old axle just ends up in a landfill! we all need to take responsibility for what we repair, and fixing should be our first thought. if it just can't be fixed, then we replace

@qualityreno9689 9 жыл бұрын

wish it was that easy! where i live there is so much rust that its almost impossible to get the cv joint out of the steering knuckle with out an impact hammer.

@temblekec 2 жыл бұрын

Man!! I love Scotty! So simple so professional. If I had teachers like him back in school I would be way farther in life 🤣

@DarrelllCampbelll 4 жыл бұрын

Thank you. I been worried about that c-clip. I wasn't sure if I was to force it out and back in. I will try the grease trick. Been looking for this answer for an hour.

@fair2guy 4 жыл бұрын

Step one: get the nut on there- Step two: UGH!!

@scottykilmer 10 жыл бұрын

either cv axle is bad on the left side, or the left wheel bearing is bad. Or, the brakes are worn down on the left side

@webventures 3 жыл бұрын

5 Star video! I had no idea this job was straight forward and simple. I am unable to do it myself (no tools, no place to do it and no experience) but I will look for someone who can but not a shop. My shop quoted me $500 for plus tax to re and re both axles Thank you so much. You are saving me at least a couple hundred bucks. :-)

@epidemia2007 8 жыл бұрын

After watching several videos this was the one it helped me the most.THUMB UP!! And thank you Scotty Kilmer!!

@Theherobrine5 4 жыл бұрын

1:46 thank you for warning me before I took it out that fluid was going to leak and get all over me

@deasttn 10 жыл бұрын

Nicely done. I see what you did there, though. You pre-loosened those bolts :-) Some of those boogers are on super tight and require a big ol breaker bar or impact wrench.

@deasttn 3 жыл бұрын

Did mine today. Thanks Scotty

@eduardene1265 5 жыл бұрын

Great little video. No bs and boring stuff. Straight to the point and detailed! Thanks man for these types of videos!

@cliffbarnes9708 Жыл бұрын

You’ve helped me keep my 2005 Chevy alive for years

@Skyefuego 9 жыл бұрын

Hey Scotty. When I drive above 40mph I can hear a humming sound, once I let go of the gas it gets louder. What can it be?

@scottykilmer 9 жыл бұрын

often worn wheel bearings

@boscopit 9 жыл бұрын

yup worn bearings. Same thing happened to me about a year ago.

@Skyefuego 9 жыл бұрын

Thanks guys!

@gamercat7004 5 жыл бұрын

Hey Scott i inserted the end of the cv axle to the transmission and drove around the block and it came off and why? I push the axle and bounce back off and does go in place when i twist the axle.

@mike856ms 5 жыл бұрын

He does it in 4:00 for me 8 hour's.

@BmwMe-uh9sy 5 жыл бұрын

then dont wrk on cars

@chavezhurtado6483 4 жыл бұрын

Do it another time and it’ll take 30 minutes, that’s what happened when I replaced lower ball joints twice

@rudelechture740 4 жыл бұрын

he had all those bolts already broken before video!

@isrealperez9069 4 жыл бұрын

It was already loose

@carmelhoneyb123 3 жыл бұрын

No time but $300 dollars for me...ughhh

@Jerkwaad 11 жыл бұрын

Very great and informative videos! I used to watch Davidsfarm, but since he is gone, you're the only automotive teacher I bother to use online.

@kwebster62 2 жыл бұрын

These videos are very informative. They also make me feel better about what I pay my competitive-rate mechanic, for these jobs.

@seanbozman5742 7 жыл бұрын

whatkind of grease did youuse on the end of shaft that you put into transmission

@yazansakran3326 7 жыл бұрын

Sean Bozman it's just CV grease. Suspension grease etc

@widtrak77 5 жыл бұрын

@@yazansakran3326 is that ok to get into the transmission? Will it mix with the fluid??

@demonaardvark6326 4 жыл бұрын

widtrak77 That’s what I’m wondering.

@FluffyMI6 5 жыл бұрын

Im actually kind of jealous how easy everything came apart for him. A CV axle nut in minnesota takes a breaker bar AND a extension, then maybe you might get the nut off. If your using anything less then a 3/4 inch drive and socket, you'll most likely break your drive. Sucks.

@carlos52321 5 жыл бұрын

He used the air tool to loosen it before removing it with a standard wrench, its what I did makes life easier

@liammorley6727 5 жыл бұрын

i live in kansas where winters are awful (not as bad as minnesota) with a 19 year old 4runner, took me and my buddy 8 hours to take off the bumpers, everythings rusted and nothing just pops out.. i feel you

@21area21 2 жыл бұрын

3/8 M12 Impact did the job for me.

@yonoit1436 4 жыл бұрын

I like how Scotty makes his video it takes You right to the point, and saves you lots of time

@scottykilmer 11 жыл бұрын

I try locking them in place using large vice grip pliers

@keithnoneya 7 жыл бұрын

Love ya Scotty, But NO NO NO, you don't have to take the two strut bolts out. Just remove the lower ball joint. Doing it your way requires you to go get a front end alignment, that adds another $120.00 dollars to the cost of the job. Heck you don't even have to remove the outer tie rod nut, it just swings out when you remove the lower ball joint Nut. Thanks for the post anyways. Best Wishes n Blessings Keith

@DIYREN1 7 жыл бұрын

+Andrew Robson top bolt is a camber bolt.

@keithnoneya 7 жыл бұрын

Andrew at 4:10 in the video he removed the upper and lower strut bolts. They did not remain tight through out the process. I have worked on vehicles for over 30 years, you don't have to take the strut bolts out on most vehicles, it's a needless step. I did a 4 part series on this to show the best way to do it. Go part 2 of 4 in my series and skip to time index 8:14 when I take the CV Axle out of the Hub Assembly. You can clearly see the lower strut bolt in my video is in and still tight. Don't get me wrong I like Scotty's videos, but he leaves a lot of things out and sometimes he leaves out some very important safety issues. If you're a backyard mechanic with some experience he's great! If you're not, he can really get you into a pickle quick and sometimes with a real safety problem. Hope this helps explain my comment on the strut bolts. Best Wishes n Blessings. Keith

@InexplicableBill 7 жыл бұрын

Dude he tightens to the correct torque by pushing his wrench with a grunt... you think he cars about someone's alignment? lol

@jcorral2 6 жыл бұрын

damn its amazing how many different opinions one simple thing can get lol

@jcorral2 6 жыл бұрын

... hey Harry Baulz (BALLS) you dip shit maybe you should learn how to comprehend a sentence ... why the fuck am i a jackass i never put down Scotty or his work ... i basically said that i find it interesting how many people responded to this video differently when it comes to something as simple as installing axles Happy New Year dumb ass

@shadetreegiants9407 9 жыл бұрын

Hey Scotty, I have a 2009 Civic with 130,000 miles. While driving, I feel vibration in the steering wheel, pedals, and seat. I've already checked tires, wheels, and alignment and all are perfect. I think it might be a CV axle issue. How do I check for this issue? Your videos are both entertaining and informative, so thank you.

@jerseyneil1 6 жыл бұрын

I had the same thing happen to my Corolla with a shaky steering wheel after the winter. Everything looked fine on the car. Finally, I rotated the tires, the fronts to the back and the back to the front. That helped considerably. Then I replaced all the tires and the car is good as new. Sometimes damage to the tires are not that apparent following a bad winter with potholes and crap on the road. Tires take a lot of abuse in winter driving.

@jopisano67 5 жыл бұрын

Sunil Thomas. My car pulled to the right when i would let go my steering wheel thinking it might be and alignment problem. I went to get new tires and it drove straight afterwards. Sometimes thats all that needs to be done.

@RSDemonof907 5 жыл бұрын

Check your rotors for warping.

@scottykilmer 10 жыл бұрын

If you like my car help, be sure to watch my live car talk show every saturday morning at 10 AM CST on google events. I answer your car questions LIVE there. Just go to my scotty kilmer channel on youtube saturday morning at 10, and click on the google plus icon on the top right corner. That takes you to the event. You do have to be a member of google plus to ask questions, so join up, it’s all Free.

@jsm2165 2 жыл бұрын

Scotty, you using a that pick fork tool really helped me out getting the CV axle out, Thank You!!

@gearhead3500 5 жыл бұрын

that grease is gonna mix with trans fluid good luck

@miguelflores5066 4 жыл бұрын

Im pretty sure jes a better machanic than u otherwise why would u be watching a toutorial on hus channel as oppose to u making videos yourself

@temuera3 4 жыл бұрын

It doesn't matter - it's a tiny amount, and whatever grease does mix with oil will simply mix anyway, as the oil gets hot while driving. Plus you should always grease any splines anyway when refitting, otherwise next time you go to remove it it will be corroded in place and be a real c#!t to remove

@irel4ever 2 жыл бұрын

Yes. Exactly what I keep thinking about. I'm doing this tomorrow. Think I'll just stick to the trans fluid for lubrication.

@thenightwing1718 6 жыл бұрын

pretty sure thats a pickle fork!

@bodeine454 5 жыл бұрын

A pickle fork pry bar! Lol

@mixmastermike1021 5 жыл бұрын

I live in Ketchikan too! Been stationed here at the CG Base for the last 3 years. Didn't think you lived here, I guess I need to watch more of your videos

@6xRedDevilx9 3 жыл бұрын

Thank scotty! Both my front right and left are pooched . I'll be doing the repair myself , with your help of course! Great video!

@markymark560 6 жыл бұрын

Scotty this is the best video on this subject. Im changing my camry cv axel soon.

@Big_Vell93 4 ай бұрын

Hooah brother. I was never airborne but y'all are still appreciated. And I appreciate you doing this tutorial as well. Thank you for everything

@MrSupernova111 2 жыл бұрын

If it was only this easy!! Great job motivating countless people to save some money by working on their own cars. Cheers!

@mrquad777 12 жыл бұрын

im 15 and im waiting till im old enough to get a apprenticeship as a mechanic in another year or so.but while i wait i am learning about stuff on the internet and i have watched about 20 of your videos and i have learnt a lot from them, more than just looking around on the internet. thanks for the videos.

@patrickellis2626 5 жыл бұрын

Scotty... great quick video. Love the grunts as you tighten the bolts!

@kevinugalde1951 3 ай бұрын

Scotty man you are a king I’ve been stuck trying to put this side in for three days

@mrlafalot 4 жыл бұрын

Thanks Scotty, I wasn't sure if I needed to tap the axle in or not. I couldn't find any other videos where that was necessary.

@erroldillon1548 5 жыл бұрын

I wish I had your experience in replacing a cv axle. I had to take the strut off of my 96 Infiniti to get the axle back in. I see people doing it without taking the strut off but there was no way that axle was going back in until I removed the strut. After I removed the strut the axle went back in with ease. It was day and night difference after I removed the strut. I followed your instructions to the T and that axle wouldn’t go back in until the strut was removed. On my 94 Honda your instructions worked out perfectly. But on the 96 Infiniti the strut had to be moved for me to get the axle to line up and go in. I’ve been working on cars all of my life but I believe it boils down to arm strength when you dealing with these axles. The stronger your arms are the easier it will be. I’ve seen several videos on putting the axle in my type of car and I’ve noticed the person doing it was huffing and puffing while they were putting the axle back in. It came down to sheer strength to put the axle back into a car like mine without taking the strut out. There maybe a special technique in putting it back in without having to take the strut out. I’m almost certain it’s all about the strength you have in your arms. I would advise anyone trying to put the axle back in to take the strut out for ease of operation if you’re not very strong. I want to say that you’re one of the finest teachers I’ve seen on the internet. You’re the finest in my book. Thanks for all of your incredible videos.

@dylanwoods2459 6 жыл бұрын

Thank you so much man, I was having such a pain putting it in, I greased and hit the end of the shaft like you did and it went straight in and took me only a minute, just trying to push it in by hand was never going to work

@potatopower4026 Жыл бұрын

Thank you Scotty! I didn't know it was safe to tap them in with a hammer. In other videos like Haynes etc they don't do that they make it seem like it slides back in like nothing. This weekend I'll be attempting to install the new one again.

@HectorHernandez-lj5ol Жыл бұрын

Scotty kilmer your a legend. I learn so much from you for years.

@blairguinea1337 7 жыл бұрын

Awesome thanks Scotty, a great help I am going to do this job in a few, replacing geabox Love your style man

@Asapfern830 3 жыл бұрын

Scotty u have helped me out so much I truly thank you no one makes good detailed vids like u 💪🏼

@hansolo6138 5 жыл бұрын

Your the best mechanic on KZfaq hands down!

@guyglot 4 жыл бұрын

I like the way you did that unlike other videos that show you that you need to remove brakes and rotor and ball joint

@n.h.moreno 4 жыл бұрын

Thanks, Scotty! I really needed this HELP TODAY!

@sidefx996 9 жыл бұрын

Great job as usual Scotty, thanks!

@westernspud504 5 жыл бұрын

hey scotty thanks for the tips , much appricated , i changed the tie rod ends on my 89 corolla never had no special puller so i just went with it wasnt that bad and they both work great ,,

@Luvly827 2 жыл бұрын

Scotty... You're truly a savage 👌🏽 I've been watching your videos forever and no one compares to you on KZfaq. Your knowledge along with clear, precise, and quick videos are unmatched. I wish you could be my personal mechanic ❤️ Where are you located?

@jonathanwebb9862 5 ай бұрын

Good old Scotty. :-) Many thanks, refreshed my memory on how to do this, particularly getting it back in (whacking it)

@mackchannel6348 2 жыл бұрын

Old content is still good content. I have a 1992 Celica AllTrac that I'll be replacing the CV axles on, and of course this is the place to come to for advice on doing any procedure on a Celica!

@davisalexander1361 6 жыл бұрын

Your video editing is pretty intense. Thanks for creating it!

@tonyharvey1 4 жыл бұрын

I love your channel, you've help me out understand my passion for fixing cars I love

@frankboydstun1109 6 жыл бұрын

Mine wouldn't go back in all the way. Followed your 'grease the end" tip. Snapped right in; Thanks.

@Divinityiscalling 5 жыл бұрын

Hope you had a good time in ketchikan Scotty. I grew up there and now live in colorado. thanks for makin great videos on how to do it ourselves

@chrraydendeeznuts6978 3 жыл бұрын

Boy! I don't know what i would do without you Brutha Scotty😎🛠

@joeybrowder930 3 жыл бұрын

Your 4 minute video saved me a lot of time and trouble. Appreciate the hell out of it.

@damianrivera7711 4 жыл бұрын

I just like how unlike other videos I seen he makes it look so easy and it really is I learned a lot from watching his videos

@jacobnickell96 7 жыл бұрын

another great stupid simple vid, Scotty. I used my G.i. bill for automotive school after leaving the Army (101st Airborne Infantry) and never had luck finding employment in the industry but make side money working on vehicles. I watch and refer to your vids for some extra knowledge and thank you for it, brother.Hopefully I get into a good mechanical gig and can expand my knowledge/experience but you've saved my ass a few times haha

@sspini 4 жыл бұрын

this man is the deal!... spitting a lot of mechanic´s tips like a hip-hop beat!

@quektea 10 жыл бұрын

Scotty, just love all of your videos. No nonsense, no bullshit no talk talk talk... Just the important points and how you do it!

@scottykilmer 10 жыл бұрын

If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on KZfaq. I answer your car questions LIVE there. Just check it out at How To Ask A Live Mechanic Car Questions Free On KZfaq . And remember, every TUESDAY I upload a new video, so don’t miss them.

@MPBADASS90 6 жыл бұрын

Thanks Scotty ya leg! Saw a video on my car but the guy was doing a lot of extra work taking off the brake rotars and calipers as well.

@zacharyhoyu4875 3 жыл бұрын

Yeah you cant help stupid ppl lol

@spookstaz 11 жыл бұрын

Wow I've watched other CV axle videos and this one really explains the steps well

@wykydrone Жыл бұрын

I've watched your video and another and honestly I'm way more confident I can do this instead of paying $700. I cannot thank you enough good sir

@truedreams1 4 жыл бұрын

Great! Other videos don't mention the fluid and how to put it back (crucial!). Although the all bolts where loosened before so it's more difficult in reality.

@scottykilmer 11 жыл бұрын

yes, often you need a slide hammer to get them out they stick badly when that old on those.