How to Replace a Moen Shower Faucet Cartridge

No video

How to Replace a Moen Shower Faucet Cartridge

Рет қаралды 39,045

Күн бұрын

In this video, I'm replacing the faucet cartridge on a Moen single-handle Eva Posi-Temp (R) shower faucet. The replacement cartridge is part 1222 or 1222HD. From the beginning until about 9:45 is the normal faucet cartridge replacement procedure. From 9:47 until the end explains what to do if the shower handle is in the wrong position (up instead of down) when the water is shut off after you've replaced the faucet cartridge.
Faucet cartridge: www.moen.com/p... or www.moen.com/c...
Shower faucet: www.moen.com/p...
This video is not sponsored by Moen.

Пікірлер: 25

@stevenarndt9087 Жыл бұрын

Thanks for this video. I especailly like that you added the part at the end because I encountered this problem and your instructions were spot on!

@LongologoProductions Жыл бұрын

@Steven Arndt: Glad it helped!

@dr.adrianyeong6231 4 ай бұрын

The last part was the gem I needed! Thanks for the very helpful video!

@LongologoProductions 4 ай бұрын

Thank you!

@matthewwarner4z4i 8 ай бұрын

This was really thorough and helpful. When mine went bad didn't think I'd be able to fix it but I did. Really appreciate you!

@LongologoProductions 8 ай бұрын

Thanks for the kind words and happy to know this helped you!

@Aurelian76 Жыл бұрын

Thank you for the video.

@user-ui5kn7ik6m 10 ай бұрын

for JmP shower, a good guide for making valve change

@e36z32 7 ай бұрын

Excellent video! Most I’ve found only show the cartridge replacement procedure which I found to be a lot easier than the posi handle installation and adjustment. I found after installing the HD cartridge that the lever is actually so easy to move that it will slip down to full hot (9 o’clock) from approximately midpoint between 10 & 11 o’clock. Have you had this happen? The plastic cartridge gets harder to turn over time I wonder if that will happen to the HD brass cartridge.

@LongologoProductions 7 ай бұрын

Thanks! I haven’t had that happen (slipping down to full hot at 9 o’clock angle) and I’ve even added lots of extra grease around the cartridge. May be a poor fit between the cartridge and the pipe? I would try removing and reinstalling super carefully to see whether it still happens.

@e36z32 7 ай бұрын

@@LongologoProductions I ordered a second HD cartridge and installed it today. The Moen handle is very heavy and seems to be what caused the first cartridge to slip. The second new HD cartridge valve is just a slight bit tighter, which seems to be enough to keep the handle from slipping on its own. I also had the 180 degrees out of sync on this one-so certainly appreciate you addressing that in the video as well! 💪 👍

@LongologoProductions 7 ай бұрын

@@e36z32 : Glad it worked out for you! Seems that some of this stuff isn’t as precise as it should be, right?

@Nunya.Bidness Жыл бұрын

Wait, so the old cartridge needed to be quarter turned to come out, but the new one didn't? Is that because you got the HD version?

@LongologoProductions Жыл бұрын

@Paul: The quarter turn is to loosen / release the old cartridge, because part of that process actually pulls the cartridge forward a bit to make it easier to remove. Inserting the new replacement cartridge is different-it is lubricated and inserts easily and you don’t turn it a quarter turn. Same for HD and for non-HD versions. Hope that helps.

@nicolasarevalo8043 Жыл бұрын

Would it be the same process to replace the cartridge for the diversion valve above the faucet?

@LongologoProductions Жыл бұрын

@Nicolas Arevalo: The parts for the shower flow control lever/valve would be different, so it really depends on the specific lever/valve you have installed. Sorry I can’t be more help.

@user-jh8vd1xu8z Ай бұрын

I cant get the Allen bolt out

@LongologoProductions Ай бұрын

First, make sure you have any gunk cleaned out of the bolt head so your Allen wrench can fully grip the bolt head. Second, make sure you have a long enough arm on the Allen wrench to give some leverage. Third, consider putting a drop of liquid wrench behind the bolt head and let it soak in for 30 minutes or so and then try to remove it. I hope that helps.

@soumyasanil7632 Жыл бұрын

Nice🎉

@Tendertroll1 Жыл бұрын

Do you like your eva? I ordered one and not sure if I made the right decision.

@LongologoProductions Жыл бұрын

@T C: we like it in the chrome finish better than the brushed nickel - easier to keep clean.

@Tendertroll1 Жыл бұрын

@@LongologoProductions that’s good, is it reliable

@LongologoProductions Жыл бұрын

@@Tendertroll1 : yes. We haven’t had any issues with it. Just replacing the cartridge every few years if the handle gets a little harder to turn. Honestly once it’s installed you kind of just stop thinking about it and it just becomes part of the bathroom….