How To Replace An Intake Manifold On A Mercedes ML350

Рет қаралды 43,730

5 жыл бұрын

Brian Eslick from How to Automotive www.howtoautomotive.com/ takes you step-by-step through the process of replacing the intake manifold on a 2008-2011 Mercedes ML350. Owing to stuck intake runners and codes P2004 P2005 P2006.
Affiliate link mentioned in the video for Mercedes-Benz Engine Intake Manifold Pierburg OEM 7.00246.33.0 / 7.00246.26.0 / 2721402401 With Intake Gaskets amzn.to/2FTQE2L
Affiliate link mentioned in the video for Bapmic 0139979045 Engine Fuel Injector O-Ring Seal for Mercedes Benz M272 M273 M275 (Pack of 10) amzn.to/2G1Vtu5
Affiliate link mentioned in the video for Milwaukee 2554-22 M12 FUEL 12-Volt Lithium-Ion Brushless Cordless Stubby 3/8 in. Impact Wrench Kit with One 4.0 and One 2.0Ah Batteries amzn.to/2KOc7Nv
Affiliate link mentioned in the video for Milwaukee (MLW255721) M12 FUEL 3/8" Ratchet Auto Kit amzn.to/2HJIDOf
New! How to Automotive T-shirts, stickers, and more! Click the link: teespring.com/stores/how-to-a...
Affiliate link mentioned in the video for How to Automotive Tool Store www.amazon.com/shop/howtoauto...
Website
For more videos, tips, and to purchase recommended tools and products visit my website at: www.howtoautomotive.com/
Stay connected at:
Email: howtoautomotive@gmail.com
Facebook: / how-to-autom. .
Google+: plus.google.com/+HowtoAutomot...
LinkedIn: / brian-esl. .
Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brian Eslick #HowtoAutomotive

Пікірлер: 53

@HowtoAutomotive 5 жыл бұрын

links for parts and tools are in the description

@Kennyapatson007 Жыл бұрын

Thank you so much for this video. I was able to DIY my intake manifold on my 2006 Mercedes-Benz ml350. The car was limp mode prior to repair but it is out limp mode after the intake manifold replacement. Your video was my guide. Thank you!

@rbnyfeler 2 жыл бұрын

Thank you Brian for posting this video. Everything is so detailed. I just replaced my manifold with your video on my side. PERFECT. The only problem I had was when putting the new manifold in the gaskets came off. I did glue them on and was able to put it in without loosing the gaskets THANK YOU

@HowtoAutomotive 2 жыл бұрын

Glad it all went well for you. Thank you for watching!

@dcyamahatech 5 жыл бұрын

The pride you take in your work is obvious. I'm a power sports tech of 17 years and I still enjoy it as much today as I did when I started. Really enjoy your videos

@sat_sonic 5 жыл бұрын

Excellent video and obviously a true professional mechanic.

@carlovincetti Жыл бұрын

This is the most comprehensive video on this job I have found:)

@josesierra2440 3 жыл бұрын

You are a pro brother... I have that oil leak and now I can take care of it myself... awesome job explaining what you are doing.

@joelkelm3970 4 жыл бұрын

such a great video love the step by step of it all. Seems tedious very possible to do in the driveway

@TOMRYANLUKE 3 жыл бұрын

GOD BLESS YOU for this video. thank you.

@janoz06 5 жыл бұрын

Awesome video thank you

@chrisfife1183 4 жыл бұрын

Great video. Thank you

@donniedye2716 2 жыл бұрын

Great video. Thank you.

@lawboy777 5 жыл бұрын

You make it look so easy! I changed out my PCV valve and cam caps on my E550 and it look 4 hrs! For some reason the 4 bolts on the valve weren't torx, they were hex. Getting an Allen key behind the motor was a nightmare....

@HowtoAutomotive 5 жыл бұрын

lawboy777 On the ML there’s a lot more room. I know your pain. Thank you for watching!

@ozzstars_cars 5 жыл бұрын

Not first. Nice job Brian

@SaultiBalldeip 3 жыл бұрын

I am in the process of doing this. Got the manifold out today, tomorrow the new one will be installed. I, of course, forgot the disco the battery and the car was beeping after I was done for the day, telling me to take it to the shop ASAP and not shift it haha...no ECU I am sure it was freaking out. Hopefully that won't cause any issues, I will disconnect the battery tomorrow before install.

@Aardvark49 5 жыл бұрын

When replacing the oil separator cover, I'm seeing recommendation to replace the Crankcase Breather Oil Separator that lies behind the cover (p/n 2730100162). It attaches to the intake cam with a reverse threaded bolt. When do you find that necessary to do?

@franciscocervantes166 4 жыл бұрын

At the begining of the video you let know working on a 2006 ml 350 but in the description it tells 2008-20011 can you let me know wich model is it you are replacing manifold on video again ..thanks

@PaulyD0859 5 жыл бұрын

I’ll bet, if you leave the tumbler flap position sensors unplugged, you’ll get 2 secondary air trouble codes. Don’t ask how I know. 🤪

@fezg123 4 жыл бұрын

Sorry to ask mate but could you please tell me where the EGT SENSOR sensor 1 bank 1 for 2012 ml250 bluetech is please? Is it under the airintake housing?

@neverstoplearning382 5 жыл бұрын

Great walk through. I am doing this job tomorrow. Wish me luck. Best regards.

@SergioGurrola 5 жыл бұрын

learningfromthebest now how did it go? Did you make it ?

@dng7794 2 жыл бұрын

Hi, I hope you still read this. I have 2008 ml350 and i need help with the following issues: 1. White smoke from exhaust started today, lot of it plus heavy gas smell. 2. I watched many youtube videos and many mention: a. fuel pressure regulator. Does this ml350 has one and where may it be? b. fuel tank pressure sensor. Where it it at? c. air / oil separator. d. crank case oil separator. 3.before this white smoke issue, had hard time to start the cat when the engine is at operating temp. Is ECT lying. It start and run just fine when cool down. 4. I recently replaced oil mobil1 0-40w, crankshaft pos sensor, 4 camshaft pos sensors, and 4 cam adjuster magnets. trying to address the hot start issue. Thanks for the infos.

@dariusphotography865 7 ай бұрын

What is the torque for the intake manifold bolts?for 2012 Mercedes ml350

@johng9095 4 жыл бұрын

I got an error light saying my camshaft timing is off but dealership is telling me its intake manifold flap. Is that plausible?

@wency101 6 ай бұрын

Great video! Thank you for showing these steps. Wha would be the total cost of a repair like this?

@HowtoAutomotive 6 ай бұрын

It’s about 3.50 hours labor. At.$150 + parts and I don’t remember what that was.

@JoseRamirez-ie2bk 5 жыл бұрын

Thank's brother

@HowtoAutomotive 5 жыл бұрын

Jose Ramirez thank you for watching!

@swift4311 4 ай бұрын

Is this OEM part? If not any problem so far?

@MariaMQueen-ov2lr 2 ай бұрын

Does a use intake manifold work

@maazdiary2969 4 жыл бұрын

Hi, I just followed your instruction to change the intake manifold on a 2010 ML350. I put a brand in intake, cleaned the fuel injectors and repacked crank shaft oil drip cover. Now when I start the car gas is leaking from the injectors and it hard to start the car. What could have I have missed to plug back in?

@HowtoAutomotive 4 жыл бұрын

Maaz Awan The injector O-rings must’ve got pinched going back in. You’ll have to order new O-rings

@maazdiary2969 4 жыл бұрын

Thanks for your reply. I did find one injector in cylinder one, which was not installed properly and top seal was leaking. I fixed it, the issue now I am getting is multiple misfire. Is it possible, that all injector seals are leaking air and causing random misfires? I did not put new seals yet. I did clean the injectors with intake manifold cleaning spray. Cleaned around and the tip of the injectors. Do you think maybe cleaning solution damaged all do the injectors? Or maybe old seals are causing air leaks in a new manifold.

@ibbi270 3 жыл бұрын

How long does this normally take?

@steveazm3898 2 жыл бұрын

hello .. do you have a shop in southern California

@trentburtch3915 2 жыл бұрын

How long did this take to replace yourself ? Total amount of time.

@scuba422123 5 жыл бұрын

plastic runner valves warping or carbon sticking not too bad of a job though it looks harder

@HowtoAutomotive 5 жыл бұрын

scuba422123 definitely one of those jobs that look harder than it is

@BennysBenz 2 жыл бұрын

I put everything back together. The car starts but has no power i put rhe pedal all the way down it does not rev. I know the sensor by tye throttle was a bit loose (not rhe tps sensor). Its a plug that's under the maf bsck of engine.

@MIKE505NICA 11 ай бұрын

How much the labor

@987kica Жыл бұрын

Hi. I just finished replacing my manifold. I double checked and I plug in everything. I am getting misfiring in my cylinder 1,2,3 and 6. What could this possibly be

@torontoonline Жыл бұрын

Could be the aftermarket manifold defective? Or could be fuel injectors installation issue? Is there any other code like vacuum leak etc..