How to Replace Blower Motor Resistor 95-11 Ford Ranger

Рет қаралды 44,924

1A Auto: Repair Tips & Secrets Only Mechanics Know

7 жыл бұрын

Buy Now!
New Blower Motor Resistor from 1AAuto.com 1aau.to/ic/1AHBR00028
1A Auto shows you how to repair, install, fix, change or replace a bad or broken blower motor resistor. This video is applicable to the 95, 96, 97, 98, 99, 00, 01, 02, 03, 04, 05, 06, 07, 08, 09, 10, 11 Ford Ranger
This process should be similar on the following vehicles:
1998 Ford Ranger
1999 Ford Ranger
2000 Ford Ranger
2001 Ford Ranger
2002 Ford Ranger
2003 Ford Ranger
2004 Ford Ranger
2005 Ford Ranger
2006 Ford Ranger
2007 Ford Ranger
2008 Ford Ranger
2009 Ford Ranger
2010 Ford Ranger
2011 Ford Ranger
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/okZ/1AXAA00013
• 19mm Socket 1aau.to/oeN/1AXAA00043
• 5.5mm Socket
• 7mm Socket 1aau.to/oi3/1AXAA00017
• 8mm Socket 1aau.to/oi3/1AXAA00017
• 3/8 Inch Breaker Bar
• Ratchet 1aau.to/omJ/1AXAA00016
• Socket Extensions 1aau.to/okJ/1AXAA00015
• Floor Jack 1aau.to/odh/1AXAA00068
• Jack Stands 1aau.to/oc2/1AXAA00065
Subscribe: / @1aauto
Check out our playlist:
Ford Ranger 1998-2012 3rd Gen: • Ford Ranger 1998-2011 ...
Ford Auto Repair Videos: • Ford Auto Repair Videos
For More Info visit us at 1aau.to/h/wA/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 29

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@downbelowu1928 3 жыл бұрын

Anyone watching this-this is by far the hardest way to do this. Instead, use a 10 mm socket and remove the bracketed piece that is in your way from the top. Remove the electrical connections that are in your way. After that their are 2 5/16 screws that hold the resistor in place, don’t try to remove resistor connector before removing screws bc chances are it will be melted. Also buy the pigtail wiring and resistor. Under $30 for all. In regards to this video-I can change my oil by taking out the engine but I’d rather not, Jesus Christ

@nzt4890 3 жыл бұрын

No kidding. This is like lowering the river instead of raising the bridge! 😲

@marktwain580 3 жыл бұрын

That’s nuts. I’ll do it from above.

@1AAuto 3 жыл бұрын

+Mark Twain Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@jconthegreat 3 жыл бұрын

You guys are a LIFESAVER!! I have the exact same model of ranger, and I use your videos for all my repairs! Thank you SO much!

@Twinspinner 2 жыл бұрын

I have the 2.3, just opened my hood, and WOW it's like right there on top lol I mean there's less stuff in the way because the engine is smaller, but this video makes it look so much further down than it actually is

@telsat 4 жыл бұрын

Great video and very useful thx guys

@patricklogsdon1 5 жыл бұрын

Great video, thanks very much!!

@1AAuto 5 жыл бұрын

Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com +Patrick Logsdon

@bestdealdoors 5 жыл бұрын

Thank-you

@1AAuto 5 жыл бұрын

+E Thank you!

@lbk1982 4 жыл бұрын

Very useful video!! Ty! Have to point out, you used a pair of wire cutters for pulling that clip, and gouged the metal of the body, right through the paint. i can't believe you used a sharp metal tool to pry that plastic piece off a painted metal part. that part of the truck already has issues with rust from being near the road grime, and from water pooling on the body as it drips off the truck during rain. no one is going to look there to find it, and it's going to rust out. to anyone watching, don't use a metal tool for doing that!! otherwise, this video is awesome.

@1AAuto 4 жыл бұрын

+lbk1982 Thanks for checking us out!

@samuelanderson1415 5 жыл бұрын

What about a video for the town car please or is it the same process

@1AAuto 5 жыл бұрын

We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. +Samuel Anderson

@samuelanderson1415 5 жыл бұрын

Thanks for replying you guys are the best

@Jose-js7ke 4 жыл бұрын

I successfully installed it. Fan speed 3 and 4 only work now. 2 still doesn’t.

@577buttfan 3 жыл бұрын

Bad pig tail

@SandCrabNews 4 жыл бұрын

When I did this on a Nissan pickup, I had to remove the glove box to reach the resistors. Better design, less time.

@1AAuto 4 жыл бұрын

+SandCrabNews Thanks for the feedback!

@FallenAngel3746 3 жыл бұрын

Nissan is garbage.

@jackbenimble9403 3 жыл бұрын

Is there a way to do this without damaging the customers paint job and marring up all the plastic?

@1AAuto 3 жыл бұрын

+Jack Benimble Thanks for watching! You can always put some painters tape on the edges of the body where the panels need to be removed. That should add some level of protection for the paint!

@Taulksik 3 жыл бұрын

You don't need paint