How to Replace Brake Caliper 2001-2005 Honda Civic

Рет қаралды 13,730

2 жыл бұрын

Buy Now!
New Brake Caliper from 1AAuto.com 1aau.to/ia/1ABCR00113
This video shows you how to install a brake caliper on your 2001-2005 Honda Civic. A worn out or seized brake caliper can create dangerous and expensive problems: overheating, rotor and pad wear, or even total failure. TRQ brake calipers are engineered to fit your specific vehicle.
This process should be similar on the following vehicles:
2001 Honda Civic
2002 Honda Civic
2003 Honda Civic
2004 Honda Civic
2005 Honda Civic
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXAA00013
• 10mm Wrench 1aau.to/oa/1AXAA00010
• 12mm Socket 1aau.to/oa/1AXAA00015
• 17mm Socket 1aau.to/oa/1AXAA00015
• 19mm Socket 1aau.to/oa/1AXAA00043
• Ratchet 1aau.to/oa/1AXAA00016
• Socket Driver
• Torque Wrench 1aau.to/oa/1AXAA00044
• Brake Fluid
• Brake Grease
• Brake Parts Cleaner
• Gloves 1aau.to/oa/1AXSS00048
• Safety Glasses 1aau.to/oa/1AXAA00343
• Drain Pan 1aau.to/oa/1AXAA00320
• Pick 1aau.to/oa/1AXAA00037
• Small Hook
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 10

@TRQ 2 жыл бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@swany65 2 жыл бұрын

FYI: there is a left side and right side caliper. I didn't know that because out of all my research nobody ever said there is a left or right. The boxes the calipers came in didn't indicate which one was right or left (it was a blank brown box). Of course I installed it the exact opposite. Did a test drive and the brakes were soft because my bleed valve was at the bottom of the caliper(wrong side of the car!) The way to have the correct caliper on the correct side is to make sure bleeder valve is oriented at top. First brake job I ever did so now I'm experienced. Also, sheared off my bleeder valve on one of the rear brakes. Guess tomorrow I'm replacing my wheel cylinder.

@depooltrd Жыл бұрын

fml, I think I have the same problem right now, they came a little different in color but same part number, I changed everything and after that I got the abs light and the pedal is going all way down, I bleed the brakes light 5 times already and Im still with the problem

@dustinsmith9247 20 күн бұрын

Good video how ever i was looking to see how you removed the line from the old caliper(pinched off etc) instead you jumped to installing it right on the new one.