How to Replace Camshaft Position Sensor 2001-2005 Honda Civic

Рет қаралды 62,982

2 жыл бұрын

Buy Now!
New Camshaft Position Sensor from 1AAuto.com 1aau.to/ia/1ACPS00051
This video shows you how to install a camshaft position sensor on your 2001-2005 Honda Civic. For vehicles with electronically controlled timing, a camshaft position sensor relays important information to the computer to ensure the engine is running properly. A bad sensor may relay incorrect or no information, resulting in poor running conditions and trouble codes.
This process should be similar on the following vehicles:
2001 Honda Civic
2002 Honda Civic
2003 Honda Civic
2004 Honda Civic
2005 Honda Civic
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXAA00013
• 10mm Wrench 1aau.to/oa/1AXAA00010
• 10mm Deep Socket
• 10mm Socket 1aau.to/oa/1AXAA00017
• 12mm Socket 1aau.to/oa/1AXAA00015
• Trim Tool Set 1aau.to/oa/1AXXX00004
• 1/4 Inch Ratchet 1aau.to/oa/1AXAA00017
• 3/8 Inch Drive Ratchet 1aau.to/oa/1AXAA00015
• Socket Extensions 1aau.to/oa/1AXAA00015
• Torque Wrench 1aau.to/oa/1AXAA00044
• Gloves 1aau.to/oa/1AXSS00048
• Safety Glasses 1aau.to/oa/1AXAA00343
• Pick 1aau.to/oa/1AXAA00037
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 28

@TRQ 2 жыл бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@CharlesGwinn-ep9pb 2 ай бұрын

Screw a bunch of that!!! 1.Place jack/wood block under oil pan 2.Remove motor mount 3 nuts. 3.Remove ac lines bracket bolt in valve cover for wiggle room. 4.Pry off round sensor dust cap and reach inside and disconnect elec connector. 5.Remove 3 upper timing belt cover bolts(hardest part) 6.Use flathead to pry lower rear of cover from its backing piece(it separates near where that rearmost bolt was).7.Carefully wriggle the cover slightly downward then back, up and out. 8.Replace sensor .. one bolt. DONE shaka lacka.

@MichaelMosesHammer 2 жыл бұрын

I removed the upper cover so easy, by just loosening the valve cover, and gently prying the upper cover lip, from the valve cover. Saves a lot of time.

@armandoramos3408 Жыл бұрын

He doesn't mention replacing the valve cover gasket but looks like he did. It looked red at the beginning, then black when replacing the cover. He also mentions not having to remove the power steering pump, but looking closely at the video, it looks like he did.

@jaymez858 2 ай бұрын

For an older car like this, might as well do a valve adjustment, clean EGR valve, replace EGR gasket, replace seals on valve cover bolts, etc.

@user-eg1ir5dc5e 11 ай бұрын

Great video! Very professional and thorough. Thank you for sharing.

@ktkawaguchi 2 ай бұрын

Thank you. very accurate video for what i went through except how long and how many tries it took me to get the sensor back in place. my only comment is in regard to not dropping the sensor's bolt. in removing it i bent a cheapo magnet on a stick and fed through my deep socket to turn it into a magnetized socket. and in replacing the bolt, i used the whole finger from a glove and covered the entire deep socket and it came out with the socket.

@javiercornejo2132 Жыл бұрын

Is it necessary to change them rings when putting the co er back on?

@elzacatecano5096 Жыл бұрын

Thx for ur video it really help me alot to replace mine

@SpaceCodes. 2 жыл бұрын

Since the valve cover seal is being broken, how important is it to replace the valve cover gasket? I didn't see you put on a new gasket so I figured I'd ask

@wilbertcoria4768 11 ай бұрын

How long have you had the torque wrench

@alexnoah9053 Жыл бұрын

the bolts head fell off mine ur removing at 5:57 Do u know where i could get one?

@S.s.s_88 Жыл бұрын

My car starts and shuts off in like 2 seconds could this be it 2001 honda civic

@popoutnshowkillas Ай бұрын

Is there only one cam position sensor or multiple???

@coopergardea9001 11 ай бұрын

Never mentions removing engine bracket. Never mentions replacing valve cover gasket…..annoying

@uramaku2730 Жыл бұрын

Thought the power steering pump you said you didnt have to take it out i seen in the vid its not there???

@ryanmood5388 2 жыл бұрын

Do you have to take the valve cover and wiring harness off too or can you just remove the 3 bolts on the plastic cover and get to the camshaft

@MichaelMosesHammer 2 жыл бұрын

Just loosen the valve cover, and remove all 10mm bolts, and 10mm nuts that hold the wiring bracket on top of the cover. Remove the 4 coils, and all wiring connectors, that will keep pressure on the valve cover. You simply pull up on the end of the valve cover, where it meets the upper timing cover, and release the upper cover, and remove it. I do them this way all the time. It's just the way I do it, and it's worked well for me.

@greeneggsandham427 Жыл бұрын

@@MichaelMosesHammer Since you are still lifting the valve cover on one end will this cause the valve cover gasket to be uncompressed and loosened and thus leak later on. Hence you will need to put on new gasket anyway???? What has your experience with leakage like????

@jasonduink6773 Жыл бұрын

Fantastic video.

@hondacivic23 7 ай бұрын

What about for a 96-00 honda civic?

@ropeysubstance1719 9 ай бұрын

Does this fix code P0340?

@CharlesGwinn-ep9pb 2 ай бұрын

Another advantage to this method is that(after you replace the sensor) you can connect the elec connector and immediately start up car and see if error code vanishes. (Maybe replace motor mount just in case?) Cant start it up with valve cover and 15 million hoses disconnected... lol.

@ThanhNguyen-ns5xx 2 жыл бұрын

Hi What year and model Honda civic?

@ryanmood5388 2 жыл бұрын

Looks like it’s a 2004 Honda Civic dx

@user-dx8fl9bl4r 6 ай бұрын

You didn’t mention that you removed the power steering lines now I’m screwed. They’re right in the way and I’m unable to move forward after ripping my car apart. Ugh.

@justmyopinion8395 3 күн бұрын

Why don’t car manufacturers just designed things so they are easier to get to? Design to upper timing cover to just pop off? Doesn’t seem like it would be too hard to incorporate in the design.