Recording Date: March 13 and 14, 2017 Location: Fresno, California General procedure on how to remove and install the exterior door handle on 1997-2001 Toyota Camry. My contact information: welkingvue@yahoo.com
Пікірлер: 65
@MrMacky-co6zn4 жыл бұрын
Outstanding detailed shots. Showing how things look from inside the door and then showing the part after it is removed really helps to understand what things look like when doing the actual repair.
@WelkingVue4 жыл бұрын
Thanks!
@lifetimedreamvideos9854 жыл бұрын
Massively helpful. You are the man! My drivers new doorhandle arrived yesterday. Now I know how to put it in. Thanks so much!
@salvadorcervantes2678 Жыл бұрын
Thanks man just had my handle snap off on me so this was super helpful!
@niceguyed97477 жыл бұрын
Thanks Mr. Vue for showing all the little details and also mentioning that the bolts might not fit the replacement handle.
@DamnSkippy16 жыл бұрын
One more thing, instead of paying more to get one that color matched, I spent less than the difference (between standard black handle approx $7 and the color matched one approx $16) and bought a can of perfect match spray paint approx $7. Your paint codes should be on the drivers door sticker to match it up with "Perfect Match." I scuffed the handle lightly with some high grit sand paper, cleaned it good, used some primer I had lying around, and then sprayed it with color match. It worked perfectly, I saved a few bucks, and I had over half a can left for some touch ups (scratches and shit like that) here and there around the body. Just thought I'd mention my approach in case someone would want to do it that way for themselves.
@WelkingVue6 жыл бұрын
Good thinking!
@ezanderson88342 жыл бұрын
This was the best video I seen doing this I will be using this one for sure
@lucasb61826 жыл бұрын
Thanks for this video .. It was great the way you showed the far away view and then panned in on the screws to remove - that way, it was much easier to see where you were working ( .. another video just showed close-ups and it was hard to see where the cap/cover and screw were located )
@thoth71972 жыл бұрын
Thanks Buddy! You did a good job and carefully explained everything step-by-step which really was helpful to an amateur mechanic like me.
@mike261384 жыл бұрын
thanks Welking, This is going to make my repair less difficult.
@francisburns15452 жыл бұрын
Welking Vue - good video - much hard work to figure out how to got out & get it - you stayed with it! Good for you and your customers!!
@WelkingVue2 жыл бұрын
Hi Francis thanks for stopping by. I prefer working on my car over taking it to a shop and when I work on other people's car it's free I don't charge anyone.
@kjemradio7 жыл бұрын
Have to do this very thing on my girlfriends 99 Camry. Passenger side though so it's the reverse angle for me. Thanks for creating the video!
@davidborn40414 жыл бұрын
Real world DIY repair. Thanks for the video.
@omarbrown59586 жыл бұрын
Thank bro. I needed the lesson
@sireliot21492 жыл бұрын
This job is a PITA on a 96 avalon. I would seriously recommend that if you're doing the passenger front door...consider how often you actually need to open that door with a key, especially if you have keyless entry. Just swap the door without disassembly - wish I'd gone that route before tearing it all apart.
@thoth71972 жыл бұрын
Thanks buddy! Your detailed instructions and video were very helpful for an amateur mechanic like me. I really appreciate the help!
@WelkingVue2 жыл бұрын
Thank You!
@michaelzolman2642 жыл бұрын
Video is good but the quickest and easiest way is .. First u pop out and disconcert that handle rod rod with a long handle screwdriver ... And then take out the two top bolts and the handle will come out just enough where u can disconnect the lock rod .... Replace back the same way but do not tighten front bolt tight at all as you or going to have to have some play in it to install that outer bolt ... Then tighten them up and Snap handle rod back into place I had to put wd on it so it would pop back in the new one easier ... Put back together every thing and you or good to go..... It only took a hour from star to finished if you tackle it like this ...Cheers
@brock20195 жыл бұрын
great video. Thanks for the details and excellent zoom in
@WelkingVue5 жыл бұрын
Thanks!
@michaelcorleone32866 жыл бұрын
Muy bien amigo! it help me a lot.
@killermacmc7 жыл бұрын
Good video; thank you.
@despicable77810 ай бұрын
Awesome my guy you helped me a ton just now
@ftchico14 жыл бұрын
Great video.
@wilberdaniel78624 жыл бұрын
What is ir the function of the metallic cylinder on the other side of the door handle?
@jerryday28513 жыл бұрын
Toyota needs to come up with a better plastic for their cars. I have a 1999 and I've change the driver door handle this is my 3rd one. The car has almost a half million miles on it and still going . Even the plastic connectors under the hood have all broken, Just not very good plastic. But I found it easier to take out the 2 top bolts out because they hold in the handle. Then from the out side lift up on the handle and pull it out. Then unhook the linkage on the key lock part then you can take the cylinder out on the out side and put it in the new one ( bottom bolt only ) because the 2 top bolts hold in the handle. then putting in the new one hook up the key linkage first the put in the handle in then last put last 2 bottom bolts.
@mursalarabia Жыл бұрын
You saved my ass bro
@MrMacky-co6zn4 жыл бұрын
Excellent video. I agree with Lucas B. The way you zoomed in and out really helped to understand where you were working and how you were getting the tools into the door.
Good vid. Never ever have seen so many ads. It would be helpful to mention the bolt head sizes when removing bolts. Also, what is the size of the new bolts for the new handle?
@lordwaffles90823 жыл бұрын
Is that door handle compatible with a Lexus ls400 1994
@slvrktman7824 Жыл бұрын
How to replace the POS Camry exterior door handle.
@Erik-kp1ux5 жыл бұрын
I'm still trying to figure out why you had to roll the window down. I guess just to roll it back up? Nice food prep gloves. Cracking me up bro!
@WelkingVue5 жыл бұрын
This recording was done a while back I don't remember unless I watch it again. I think I had to roll the window down to get access to the bolts.
@Ken.-4 жыл бұрын
The window blocks access to the bolts. That's why you rolled it back up. You just say that it would make it easier to take the panel off. Though I'm not sure why. Maybe if you need leverage to pry it off and the window is in the way.
@stevencorbo12206 ай бұрын
Do their M6 metric 6 mm and the most important part of the video you cut out which is putting everything back
@stevencorbo12206 ай бұрын
Why did you list this under Toyota Avalon
@abbigalestevenson37594 жыл бұрын
At 22:16. The rod. Beside it clicking up top, where does it lock in the bottom of that rod. I can't figure it our.
@WelkingVue4 жыл бұрын
I recorded this back in 2017, so I don't remember. I did forward it and took a look at 22:16. So one end of the rod clip to the top and IF YOU ARE ASKING WHERE THE OPPOSITE END OF THE ROD CLIP ON TO? I only watch from about 21:10 to about 23:00. I don't think I did anything to the opposite end of the rod. If you need more help, let me know I'll look into this farther.
@southerngraceofga6 жыл бұрын
Watched the video twice and I feel confident I can do this! Let u know......
@WelkingVue6 жыл бұрын
Let me know if you have any questions I'll try to answer.
@jaypowelljustgo4it2724 жыл бұрын
the worst vid i have watched so far.....
@Afib95 Жыл бұрын
My problem is the new door handles came with new screw hardware and the old screw hardware doesn’t fit the Hold in on the new door handle and I can’t find anything that fits
@WelkingVue Жыл бұрын
If you can rephrase that I can try help.
@PlumbNutz6 жыл бұрын
There is a better, easier way to do this. The lock mechanism can be removed from it's plastic connector and actuator rod and that lower left bolt which is so hard to install can be attached to the handle outside the door. Then the handle can be partially put in the door and the rod reconnected very easily. Then the two easy bolts and the one rod to the handle. It's near impossible to get that lower left bolt in when the handle is in the door.
@israelisrealallpraisestoth8129 Жыл бұрын
M you make sense I'm struggling with my Avalon I bought a perfect donor door and struggled all night with exactly what you were talking about
@michaelzolman2642 жыл бұрын
The bolts or 6mm by 12mm
@mark95596 жыл бұрын
good vidio . but why you not replace with same color ? they have in stock now it look like fortune cookie .
@kevinbrislawn59186 жыл бұрын
you got that crap after market" Toyota part on Ebay right? I had the same problem and could only get one screw into the door frame to hold the handle in..piece of crap after market. the original does not have a threaded screw in the toyota is just a non thread hole that uses a plastic to make hole with heavy metl screw
@plurbunniee29625 жыл бұрын
2005 Toyota solaria
@DamnSkippy16 жыл бұрын
Dude, I had the exact troubles you had doing this. My wife was wondering what was taking me so long to install the handle. I bitched about every issue you mentioned here, at the time I did mine. I showed her this video and she immediately realized what I was complaining about at the time is common to others trying to do this also. Then I slapped her in the face and told her to make me a sandwich. LOL j/k
@erickimmy14934 жыл бұрын
Haha I'm dying
@stevencorbo12206 ай бұрын
Dude lift the handle out before you try and take the bottom out
@poca0075 жыл бұрын
Hubby just snapped off the exterior handle, 6 months ago he broke the interior one with his huge man hands😤
@chrislnflorida51922 жыл бұрын
Sorry guy, bad video!
@htreid78463 жыл бұрын
Talk to much, a lot unnecessary, get to it already..