How To Replace Front Axle Shaft 1998-2011 Ford Ranger

Рет қаралды 60,235

3 жыл бұрын

Buy Now!
New CV Axle Shaft from 1AAuto.com 1aau.to/ia/1AAXS00175
A front axle shaft has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new front axle shaft, install a quality TRQ axle that is engineered to your vehicle’s specifications. This video shows you how to install a front axle shaft in your 1998-2011 Ford Ranger.
• Check here for more videos on the 1998-2011 Ford Ranger: • Ford Ranger 1998-2011 ...
This process should be similar on the following vehicles:
1998 Ford Ranger
1999 Ford Ranger
2000 Ford Ranger
2001 Ford Ranger
2002 Ford Ranger
2003 Ford Ranger
2004 Ford Ranger
2005 Ford Ranger
2006 Ford Ranger
2007 Ford Ranger
2008 Ford Ranger
2009 Ford Ranger
2010 Ford Ranger
2011 Ford Ranger
Tools you will need:
• Pry Bar 1aau.to/oa/1AXAA00020
• Brake Caliper Hanger 1aau.to/oa/1AXAA00084
• Straight Cutters
• 3/8 Inch Air Impact Gun
• 3/8 Inch Drive Ratchet 1aau.to/oa/1AXAA00015
• Ratchet 1aau.to/oa/1AXAA00016
• Socket Driver
• Torque Wrench 1aau.to/oa/1AXAA00044
• Bungee Cord
• Paper Towels 1aau.to/oa/1AXSS00035
• Rust Penetrant
• Center Punch 1aau.to/oa/1AXAA00055
• Floor Jack 1aau.to/oa/1AXAA00068
• Hammer 1aau.to/oa/1AXAA00091
• Jack Stands 1aau.to/oa/1AXAA00065
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Ford Ranger 1998-2011 3rd Generation: • Ford Ranger 1998-2011 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 35

@TRQ 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@juan_rico4294 Жыл бұрын

My 2 cents : don’t undo the lower shock bolts unless absolutely necessary. I was able to snake my axle out while leaving the shock bolts in. My shock bolts look absolutely dreadful; I anticipate them breaking upon removal , but that’s a job for another day.

@Deon0026yickadee 3 жыл бұрын

Great work. Magical at the end I noticed you did your shocks, rotor and brake caliper housing replaced! All at once . Night five

@TRQ 3 жыл бұрын

+Deon 0026 Thanks for watching our video! 1aau.to/m/Shop-TRQ

@davidpotts3844 10 ай бұрын

This was the cleanest and direct video for this procedure I have seen and included all toque specs

@foundwheels1939 10 ай бұрын

Why are you not mentioning bolt sizes. Feels like a rushed instructional

@zachread3775 9 ай бұрын

Well done. I love that this video has torque specs. That's not common enough for repair videos. Thanks for the help!

@yankeecrow5 Жыл бұрын

Great video, your talk as you walk through the process was, well I'd have to say the best I've heard out if everyone of the videos I've watched on here great tutorial. Thanks for your help

@Rxyzfate3 8 ай бұрын

I have a 99 Ford ranger in it only has a plastic snap ring that holds the axle into the hub

@mts7274 5 күн бұрын

Is it possible to leave the axle in the hub assembly when lowering that steering knuckle off the ball joint shaft? I was wanting to pop the axle out of the differential and remove it while still attached to the knuckle and hub.

@eldinpeterson3760 Жыл бұрын

do you have any videos on removing the front diff cover thanks.

@joycegiasson5219 7 ай бұрын

Thanks for sharing. Good job.

@nofloco3175 2 жыл бұрын

How come nobody ever mentions the bearing inside the differential that the axel will sit in? Is this something that just doesn't usually go bad or would it be a huge pain in the a to replace?

@viktortehnikmandiri3173 2 жыл бұрын

Boskuu saya mau nanya saya punya renjer tahun 2010 tiap saya masukin 4x4 jalan nanya dikit aja punyi ctek""" tapi kalau jalan lurus gak punyi gituu apanya kira"" bosku ???

@jessiejames5577 2 жыл бұрын

Thanks

@johncraig4354 Жыл бұрын

best damn video I have seen on u-tube

@jessiejames5577 2 жыл бұрын

Gracias muchas Gracias

@petrussd8881 3 ай бұрын

What is the nut size for the CV joint?

@earthtrailseco-adventures2271 2 жыл бұрын

hi i bought this exact part for my truck but it doesnt come with the spiral locking clip which holds the cv shaft in place and stabilizes the 4 wheel hub,where can i get the spiral locking clip to buy?

@kylerteague7916 2 жыл бұрын

We're you ever able to get your CV tight and not clicking? I have the same 4x4 vacuum hub and could never get the new cv axle tight. You can get a new spiral clip on amazon

@shaunoloughlin7866 2 жыл бұрын

good video and instruction but could you have found a more rusted truck!!

@Formula_47 2 жыл бұрын

Can you do this without removing the outer tie rod from the steering knuckle? if not, would you have to get an alignment after this procedure? thank you.

@cheesecurd100s 2 жыл бұрын

Dont need an alignment as the tie rod is going back in the same spot on the knuckle

@markbaker5167 2 жыл бұрын

I managed to get my bad one out but had to turn the wheels and try from different angles. The new one went in really easy however.

@ducrnd 2 жыл бұрын

when I do this, I put an alignment mark on the parts to put them back in position

@probmxmel Жыл бұрын

Thanks for the video. I’m doing the passenger side (uk) and cannot get the axle out from the transfer case. It’s even more difficult to get to it - does it simply knock out with the pry bar like the video Has anyone done this on the other side? I cannot find a video anywhere!

@michaelparker-smith8773 2 жыл бұрын

Hey, just done this and my abs light is now illuminated, took it for a drive to see if it would clear but it hasn't. Typical, when I removed the sensor, it was plastered in rust. Now it's clean, it's refusing to work 😂

@brasilprasempre6898 7 ай бұрын

Replace that lower control arm while you're at it

@juan_rico4294 Жыл бұрын

Give it a couple loving bonks

@justinkase8669 2 жыл бұрын

Dude I need the passenger side 😭

@probmxmel Жыл бұрын

Currently doing the passenger side - I’ll update you when I get it out! 😉

@geraldfasold1332 Жыл бұрын

99 ford ranger 4x4 do not have a outer nut !!!!

@CarlosHernandez-eg8oc 2 жыл бұрын

what kind of Ford Ranger is that because I have a Ford Ranger and it doesn't have those parts, I BELIEVE you got confused in the title of your video.🤔🤔🤔🤔🤔

@zachsmith98 2 жыл бұрын

If your Ranger isn’t 4x4 it wouldn’t have CV axles as you don’t need to power the front wheels.