How To Replace Front Brakes 2004-10 Toyota Sienna

No video

How To Replace Front Brakes 2004-10 Toyota Sienna

Рет қаралды 34,684

Күн бұрын

Buy Now!
New Brake Rotor from 1AAuto.com 1aau.to/ia/1ABR...
Brake pads wear out over time, much like tires, and need replacing, on average, every 50,000 miles, with variations depending on driving habits and environment. Brake rotors may also need to be replaced if they are warped or grooved. Often, it’s safer and more cost effective to replace pads and rotors at the same time. Squealing or grinding noises, or wheel vibration are all symptoms of worn brakes. This video shows you how to install new, quality TRQ brake pads and rotors on your 2004-10 Toyota Sienna.
• Check here for more videos on the 2004-2010 Toyota Sienna: • Toyota Sienna 2004-201...
This process should be similar on the following vehicles:
2004 Toyota Sienna
2005 Toyota Sienna
2006 Toyota Sienna
2007 Toyota Sienna
2008 Toyota Sienna
2009 Toyota Sienna
2010 Toyota Sienna
Tools you will need:
• 14mm Wrench 1aau.to/oa/1AXA...
• 17mm Socket 1aau.to/oa/1AXA...
• 21mm Socket 1aau.to/oa/1AXA...
• Brake Caliper Compressor Tool. Quad Piston. Ratchet Style. 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Brake Grease
• Copper Anti-Seize
• Hammer 1aau.to/oa/1AXA...
• Wire Brush 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Toyota Sienna 2004-2010 2nd Generation: • Toyota Sienna 2004-201...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 28

@TRQ 2 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@chilitoday Жыл бұрын

That’s the way to do a damn video. To the point, clean edit, No music. Thank you

@TRQ Жыл бұрын

+chilitoday Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@slycry2941 10 ай бұрын

Bro that wire brush was so good, underrated

@djmips 7 ай бұрын

2:06 he's a miracle worker with that brass brush!

@michaelfoort2592 9 ай бұрын

Looks like youve done that a few times. Thanks! Very clear and complete

@puderjim 2 жыл бұрын

Excellent video.....I spent an hour looking through other vids to see the placement of the clips.....very clear and lighted area also...thanks

@phillipcampbell3609 10 ай бұрын

I changed the front and rear brakes on my 2010 Sienna after watching this video and helped out a great deal. Thank you.

@arterialturns 3 ай бұрын

This video was invaluable, thank you so much. As others have mentioned, the simplicity of presentation and instructions are much appreciated.

@davidanthony8909 Жыл бұрын

Excellent concise and best video on this by far.

@shanefowler3504 Жыл бұрын

Had to turn the wheel out and use a pipe over the wrench for leverage to get those 17mm bracket bolts free.

@mavwayne4u 3 ай бұрын

Thank you!!! I can do that

@ohicanchangethis 4 ай бұрын

Can you do the job without a caliper compressor? If so, what do you have to do?

@milindkhurd 2 жыл бұрын

Hi, on a 2008 sienna while replacing broken stud on passenger side wheel I took the caliper slide pins out to lube. Did not note which one goes on top and bottom. One has a rubber seal at the end of the pin. Please help. Let me know which pin goes at top. The one with rubber on pin or the slated one? Appreciate the good videos.

@pokeynewsome2804 2 ай бұрын

A locking lug nut on those wheels, 😂 they look exactly like my Toyota sienna.

@josebautista8551 2 жыл бұрын

I’ve noticed that there’s some play on the rotor and the studs, is that normal?

@FreeeWIFI Жыл бұрын

what size bolt is that? I need buy to drill into the rotor to release it.

@naaawww3737 2 жыл бұрын

Great video. It would be great help if you could list tools and sizes used . Its my second language and im trying to figure out the tools for taking the little bolts that keep the rotor in place. Thanks.

@stevewaterfield4862 Жыл бұрын

Thank you. I appreciate your help.

@carlo54377 9 ай бұрын

Excellent video!! Subscribed.

@neovisionservicesgroup5031 Жыл бұрын

Agree @davidanthony8909, "concise". Excellent instructional video. Thank you for including the Torque settings.

@kovalenkoihor4325 Жыл бұрын

I have the same situation with my breaking disc, like as much exactly the same that I would think those are mine (car was staying still for a couple of years). Can it be, that because of that rusty discs, I feel pulsation in pedal when I'm breaking? Another question. Can I paint the break caliper? Does it become hot?

@evanlosset6934 10 ай бұрын

Perfect video thanks

@user-ux8xg6ff9x 11 ай бұрын

Thank youuuu 😊

@frankflores3551 8 ай бұрын

Forgot to add red brake noise resister..but good job

@rafaeladelgado2161 2 жыл бұрын

KZfaq changing brakes on Toyota Sienna 2008

@CrazySkippyHD Жыл бұрын

I have noticed with all your brake jobs.....never show us dealing with rotor screws, in the north we have to add heat, sucks because this is the second vehicle i am watching about it from you and both you skipped lol cmon show us the truth of it being corroded and seized