How to Replace Front Exterior Door Handle 06-11 Toyota Camry

Рет қаралды 135,716

1A Auto: Repair Tips & Secrets Only Mechanics Know

6 жыл бұрын

1A Auto shows you how to repair, install, fix, change or replace a broken or snapped off Exterior / Outside door handle. This video is applicable to 09 Toyota Camry
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/tsh/1AXAA00013
• Phillips Head Screwdriver 1aau.to/tsh/1AXAA00013
• 10mm Socket 1aau.to/tJa/1AXAA00017
• Trim Tool Set 1aau.to/tfR/1AXXX00004
• Side Cutters
• T25 Torx Driver 1aau.to/tmy/1AXAA00008
• T30 Torx Driver 1aau.to/tmy/1AXAA00008
• Ratchet 1aau.to/tQs/1AXAA00016
• Socket Extensions 1aau.to/tV5/1AXAA00015
• Gloves 1aau.to/tcb/1AXSS00048
• Wire Ties
For More Info visit us at 1aau.to/h/aI7/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 58

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@gblikestosew 2 жыл бұрын

Kh.

@davidgold5961 2 ай бұрын

1:28 the correct way to remove those clips is to push the center pin in, it will pop in about 1/8 of an inch and then the whole thing can be pulled out. To reinstall it, position the pin so it is protruding outward, and then pop the whole thing back into the hole.

@MarysaLavone 4 ай бұрын

My door handle just fell off today when I went to open my passenger door. I’m super pregnant but this video gives me the confidence to replace the handle myself. Thank you

@FrydriceT4R 4 жыл бұрын

Just wanted to mention the door handle design appears almost identical to 2006-2012 Toyota Yaris (US models) and the mechanisms are quite similar. Thank you 1A for posting this to help me out.

@1AAuto 4 жыл бұрын

+Ron Helmuth Thanks for checking us out! 1AAuto.com

@ChristopherRoss-ps4dv Жыл бұрын

Footnote: care must be taken to ensure the door unlock rod is properly aligned during reassembly. It can slip downward inside the door after it is removed from the inner side of the door handle and not make proper contact to the door latch upon reassembly. The top of the rod end can be popped back in-place in the inner door handle without the bottom of the rod performing the unlock action on the doorlatch.

@ZaidisFamily 3 жыл бұрын

I watched your video and followed the step. It could not be easier. Thanks for your video. Dealer wanted $135.00 to install it . Thanks again my friend. you are the MAN

@1AAuto 3 жыл бұрын

+Nusrath Zaidi Thanks for the feedback!

@0samaK 3 жыл бұрын

Such a nice calm relaxed video then when I do it 5 mins of hell begin

@jmhg2007 4 жыл бұрын

Would this be the same process for a 2011 Toyota Venza? They seem to have the same door design. Thanks.

@rickyflo3 2 жыл бұрын

Awesome video! Was very simple!

@zechenwei1139 3 ай бұрын

it looked a lot easier in the 2012 model video. did the design change?

@DFosterXP Жыл бұрын

Thanks for the video. Very helpful

@ThanhNguyen-ns5xx 2 жыл бұрын

The best video. Thanks

@gsgcarreviews 2 жыл бұрын

Well thorough 🤟

@christwisdale8315 5 жыл бұрын

Thanks man! This really helped me out. First time ever doing anything like this and was done in about an hour

@1AAuto 5 жыл бұрын

+Chris Twisdale Thank you for your positive feedback! We are happy we could help.

@jamesdelb6885 11 ай бұрын

Excellence. Thank you.

@Havokmega 4 жыл бұрын

Attempted on a 2014 Camry SE passenger side. I was good right until about 6:45. I applied to much pressure and the hole metal rod fell somewhere, I'm still looking for it. Then around 10:20, I put that little hex key in but it didn't hold the piece on inside. Since I tried doing this solo, I figured I'd get some duct tape to try and hold it in place...then I let the door close. I figured maybe I could reopen it by pulling on either the green or white cables, but when pulling them, one of them snapped! Not sure what that was but I'm sure I'll have to put that back wherever it attaches. For now I'm going to try and get a retractable mirror to find that little metal rod and call a friend to hold that piece in place while I insert the new handle. Good video, but the job is a bit tougher than it looks. Oh well, gotta learn somehow!

@1AAuto 4 жыл бұрын

+Havokmega Thanks for watching us and providing the feedback!

@THEWEEDRESERVE 2 жыл бұрын

Do you think it’ll be the same thing for a 2017 Camry se ?

@eddc1059 Жыл бұрын

So I replace all of this and the door handle will not attach to the door handle mechanisms, I don’t know what I did wrong please explain how the door handle attach to the door handle mechanism please 🙏🏼

@jamescc2010 Жыл бұрын

Lexus RX350 handle is pretty stuck after removing the lock. Actually it came out by accident the other day, we put it back without realizing it might be broken and now it is not secured in place and doesn't work on door open. I will try to slide it out again tomorrow and inspect. I will make sure the rod connection is good for the handle and actuator.

@ourfamilytravels7083 3 жыл бұрын

Been trying to get the lock to bolt in and it doesn't align. Please explain how this would even be possible.. what am I missing?

@nicolereyes21 3 жыл бұрын

Thanks bro

@1AAuto 3 жыл бұрын

+Nicole Reyes Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@craigzilla100 3 жыл бұрын

How about a 2013 camry rear door with no key lock? Looks like it can be replaced from the outside (hoping!!)

@airfelisan9344 4 жыл бұрын

Do you have one for the 5 Gen 4runner door handle replacement chrome to black videos

@1AAuto 4 жыл бұрын

+Air Felisan We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1AAuto.com

@bradleybruno30 2 жыл бұрын

I can’t find the part on ur website…. Bought one from autozone and it don’t fit 🤦🏻‍♂️

@spitchygaming 6 жыл бұрын

help, i have removed everything but i only now need to remove the door handle left. and its stuck in the opposite side of the lock, its stuck in the plastic mount on the inside of the door, i cant slide it back and out. please help, will donate if you have advice! thanks!! i can see everything but cant figure out why its stuck , its only the handle and plastic on the inside of the car door left now

@Leol77l 6 жыл бұрын

💞🙌

@ChristopherRoss-ps4dv Жыл бұрын

First, ensure that the inner plastic door handle is still secured inside the door. Next, ensure the plastic clip is removed from the rod. Next, ensure the lock cylinder is removed and you have access to the rod through the hole in the side door. Using a drift (I used a 6" 3/8 extension) and a mallet, gently pop the rod from the inner door handle.

@idislikerachetz1 3 жыл бұрын

Do u guys sell that door handle mechanism ?

@1AAuto 3 жыл бұрын

+Brisco Dta We would be happy to look up that part for you. What is your VIN#

@THEWEEDRESERVE 2 жыл бұрын

Are these the same steps on a 2017 Camry SE ?

@1AAuto 2 жыл бұрын

+The Weed Kitchen TWK The install should be the same or similar. Buy this part on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

@AlteredState76 4 жыл бұрын

Just bought a used 2007 avalon all the door handles have rust stains leaking from underneath gonna have to take them all off and clean everything hope its gonna be as easy as the Camry lmao

@garyv2196 8 ай бұрын

You had to take the whole barrier anyway.

@MC-hs4mf 2 жыл бұрын

T25 or T30 make up your mind!!!!

@BilalKhan-eh1gh 5 жыл бұрын

How different is the process for 2012 Toyota Camry?

@1AAuto 5 жыл бұрын

+Bilal Khan We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. Hope this helps you out 1aauto.com

@KBQuick81 3 жыл бұрын

Perfect!

@unclegeorge4629 5 жыл бұрын

Nice video but please change gloves after touching the butyl tape so it doesn't transfer to the rest of the door.

@1AAuto 5 жыл бұрын

+Uncle George Thanks for the feedback! 1aauto.com

@smithmartin8545 4 ай бұрын

It’s really annoying how I have to watch two advertisements every time I skip a minute or two around the video. I’m going to find a different channel for this.

@smithmartin8545 4 ай бұрын

WOW and now I’m just realizing the obnoxious amount of stuff that DOES NOT even need to be removed to swap the door handle! So much extra work! Y’all have wasted so much of my time oml

@juanleon-fh3qt Жыл бұрын

@paulrivera8423 3 жыл бұрын

um.. did he really have to do that.. you could have just skipped to the last two parts easily

@1AAuto 3 жыл бұрын

+Paul Rivera We appreciate the feedback. Sometimes there are multiple ways to accomplish the same repair.

@Raygetplenty 2 жыл бұрын

Facts all he had to do was remove the key cylinder and slide the handle out , these guys r tripping tf out

@chrisearle7886 2 жыл бұрын

What a JOKE! You can skip all the UNNECESSARY steps and go 7:30 of this video. Only the one side door screw is necessary,.... no need to take off the door panel. Should only take 5 minutes.

@ceegabe1555 2 жыл бұрын

That's what I was thinking after seeing a Hyundai or Kia YT video...

@THEWEEDRESERVE 2 жыл бұрын

doesn’t the silver rod control the handle? how do you know if the silver rod is in place when the panels on?