How to Replace Front Lower Control Arm 2013-15 Ford Police Interceptor

Рет қаралды 79,129

4 жыл бұрын

Buy Now!
New Control Arm with Ball Joint Set from 1AAuto.com 1aau.to/ia/1ASFK06039
Control arms are a crucial part of the suspension system of your vehicle. They not only carry the load of the vehicle to the wheel, but they typically also maintain its alignment. Control arms are typically large and strong, so you may be surprised it needs replacing. They contain rubber bushings for smoother rides at the cost of eventual wear, or integrated ball joints that require replacing the entire arm when they wear. This video shows you how to install a new quality TRQ lower control arm with ball joint in your 2013-19 Ford Police Interceptor Utility.
• Check here for more videos on the 2013-19 Ford Police Interceptor Utility: • Ford Police Intercepto...
This process should be similar on the following vehicles:
2013 Ford Police Interceptor Utility
2014 Ford Police Interceptor Utility
2015 Ford Police Interceptor Utility
2016 Ford Police Interceptor Utility
2017 Ford Police Interceptor Utility
2018 Ford Police Interceptor Utility
2019 Ford Police Interceptor Utility
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXAA00013
• Phillips Head Screwdriver 1aau.to/oa/1AXAA00013
• Pry Bar 1aau.to/oa/1AXAA00020
• 11mm Wrench 1aau.to/oa/1AXAA00010
• 18mm Wrench
• 15mm Socket 1aau.to/oa/1AXAA00015
• 19mm Socket 1aau.to/oa/1AXAA00043
• 21mm Socket 1aau.to/oa/1AXAA00043
• 24mm Socket
• Bearing Puller
• Bearing Separator
• Locking Pliers 1aau.to/oa/1AXAA00139
• 1/2 Inch Air Impact Gun 1aau.to/oa/1AXAA00252
• Torque Wrench 1aau.to/oa/1AXAA00044
• 15/16 Inch Wrench
• Cloth Rags 1aau.to/oa/1AXSS00035
• Soapy Water
• Hammer 1aau.to/oa/1AXAA00091
• Rubber Mallet 1aau.to/oa/1AXAA00413
Subscribe: / @trq
Check out our playlist:
Ford Police Interceptor Utility: • Ford Police Intercepto...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 52

@TRQ 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@calebwhitefilleul7959 2 жыл бұрын

Do you have a link to the bearing separator and puller kit?

@jamiespindler5040 3 жыл бұрын

Did he really just say "it's recommended to torque this bushing with the weight of the vehicle on it..."but it's too hard to get at the bolt that way.. " and than proceed to just torque in the wrong position. Next time just put a jack under the ball joint and jack the arm up till it just takes the weight of the vehicle. That way you won't be changing that bushing again in 3 months when it just rips itself apart from being torqued in the wrong position

@whambymedia Жыл бұрын

These police interceptor utility videos were exactly what I needed! Thank you!!

@Richard5873 2 ай бұрын

Does this on my 2015 Ford Explorer Limited 4WD this weekend. Just finished writing down all socket/wrench sizes and torque specs for finishing up. Looks like Best video of here on internet [ Thanks a Million !! ]

@ianmackey6097 2 жыл бұрын

Just buy the full assembly with all bushings and ball joint not much more expensive . No need to press bearings. Time is money

@auctionfiendsf 4 жыл бұрын

It's almost like you made this video right when I ordered the part! Perfect timing

@josepharagon8259 2 жыл бұрын

Use a sawsall- cut along the groove and the thing just pops off….

@mph5896 Жыл бұрын

I HATE working on Ford suspension. That nut on the ball joint will spin until your head spins. Then you use the hex 10mm to hold it and round that off. 😉Then you take out the torch and try not to melt everything rubber around it, like the CV boot. 🤨

@Queendae23 3 жыл бұрын

Make more videos this helped me alot sir

@TRQ 3 жыл бұрын

+Queen DAE Thanks for watching our video! 1aau.to/m/Shop-TRQ

@YalikemyTigerBeat 2 жыл бұрын

The aluminum mount install. Is a nightmare! My dead blow was leaking sand by the time it was close to being in position

@carpiowilliam713 2 жыл бұрын

I used a block of wood with a mini sledge and it went in just fine

@sparkythedetroitdoggo8281 Жыл бұрын

Put the bushing in the freezer for 45 minutes . Freezing shrinks the rubber . Mine slid right on with 3 taps of the hammer .

@chriscole9621 2 жыл бұрын

Just had an accident in our taurus sho, Crashed into a tunnel wall in the rain because the car understeered. Somehow at 40mph the only damage was the ball joint on the control arm and the tierod plus since it hit the wheel on the wall the wheel got some big gash marks. no body damage somehow. Helpful video, Thanks Really needed to see how to remove that bushing since mine doesn't come with one

@gregl6002 Жыл бұрын

bald tires

@alfredkoko6955 3 жыл бұрын

will this be the same as the taurus ford 2011 v6 3.5 sel i think that were my clunking noise beside the sway bar link..!

@dosedney 7 ай бұрын

hello guys great video. But tell me, does the lower control arm for the police interceptor (PART Number GB5Z-3078-E) fits the Sport Model?

@fredkuhn165 2 жыл бұрын

No idea what to do if I’m re using the ball joint lol. Threads are super tight near the top, despite wd40 and wire brushing, working back n forth. Don’t want to buy control arm, I already got the large bushings. That’s all I need

@sharonthomas7787 3 жыл бұрын

I had my right arm replaced on a 2010 Flex and the next day was wobbling said I need a front end alignment

@Latin_Throne Жыл бұрын

How did you torque the bolt you just said if you have the availability

@isacchris1 3 жыл бұрын

Why did you reuse the old mount when the new lower control arm comes with a new one already mounted and ready to go?

@danieldyer1 3 жыл бұрын

If you are talking about the round aluminum mount with the rubber bushing inside, I think the control arm assembly they sell doesn’t come with that, although some other vendor’s assemblies do. That mount is often worn out too , although the one they reused in the video looked ok.

@PaulMcLove 3 жыл бұрын

Perfect 👍😉😀

@jaydee427 4 жыл бұрын

Great video, but I have one question? Under what circumstances you would have to change the control arm? If the ball joint is fine, but the bushing is worn (and vise versa), wouldn't it be cheaper to replace just the bushing instead of the entire control arm?

@josebravo388 4 жыл бұрын

Currently doing the bushing as the arm on my vehicle is 200 a piece and bushing are 50

@ewartbuilt660 3 жыл бұрын

Cheaper on long run plus you get new ball joints as well

@isacchris1 3 жыл бұрын

You replace the lower control arm when you start to feel a shake in the floor while accelerating because the control arm bushings are bad!

@josebravo388 4 жыл бұрын

What’s the name of that tool and where can I buy it

@StormxRaiden 2 жыл бұрын

What torque wrench is that

@mablenay Жыл бұрын

how many shop hours does this require for a trained tech?

@Rodecpt0 3 жыл бұрын

Did he just hammer that large control arm bushing on? I tried to do that and it’s almost impossible without a press

@josepharagon8259 2 жыл бұрын

When I received my bushing, it was the wrong one! Looks the same but had rubber on the inside, this would of made it nearly impossible to hammer in. The ones that will hammer in are metal and have slight ridges….

@KBMOTORSchannel 4 жыл бұрын

Buy the whole arm with mount for $115!!! Cheaper in the long run after labor cost. I just bought both sides for mine and they go right in

@isacchris1 3 жыл бұрын

If you replace one always replace the other that goes for brakes and all suspension parts!!

@gedionsamuel2256 3 жыл бұрын

Where did you get it and what brand?

@joshjohns638 3 жыл бұрын

Orilley, lifetime warranty. 115.00

@chriscole9621 2 жыл бұрын

@@joshjohns638 257 dollars now

@elinoamrichter162 2 жыл бұрын

There is no way that ball joint came out that easy

@kickdog6934 2 жыл бұрын

Hi. Sr. are the ball joints replaceable?

@serapioterrones3920 Жыл бұрын

Ever find the answer??

@omahasho4658 3 жыл бұрын

Yea I hit a curb and tore the bushing and said fu*k it and bought a control arm with a new bushing which I can replace my self unlike just getting an bushing and not being able to access the bolt

@NG-tz8wo 3 жыл бұрын

I did this today. Just a warning make sure you don’t let the axle pull out. I made that mistake.

@TRQ 3 жыл бұрын

+N G Thanks for the tip! 1aau.to/m/Shop-TRQ

@wademathias151 3 жыл бұрын

How did you correct this

@NPAPOLICE978 2 жыл бұрын

What do you mean dont let the axle pull out?

@tonydushaj3912 3 жыл бұрын

Why would TRQ give you a control arm without a large control arm bushing attached ? Why would you go through all that trouble to replace a control arm with an old bushing. Replacing it with a new one takes about 300 whacks with a dead blow hammer. Removing the old one is impossible without the tools you see in the video. I wish TRQ would charge a little more and give you what you need . I had a hell of a time getting a new bushing on the control arm. Never Again

@smurphyt731 2 жыл бұрын

Were you able to get it on with just a dead blow? I'm having a hell of a time getting this stupid bushing on the new control arm its ridiculous the last set for my last vehicle came with it already pressed on.

@nikitaso 3 жыл бұрын

in less than 7 minutes!

@TRQ 3 жыл бұрын

+nikitaso Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@TripodsGarage 3 жыл бұрын

My bolts didn't come off this easily, especially the one by the knuckle.