How to Replace Front Wheel Bearing 2006-2011 Honda Civic

No video

How to Replace Front Wheel Bearing 2006-2011 Honda Civic

Рет қаралды 42,649

Күн бұрын

Buy Now!
New Wheel Bearing from 1AAuto.com 1aau.to/ib/1AAX...
This video shows you how to do the replacement yourself on your 2006-2011 Honda Civic. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This process should be similar on the following vehicles:
2006 Honda Civic
2007 Honda Civic
2008 Honda Civic
2009 Honda Civic
2010 Honda Civic
2011 Honda Civic
Tools you will need:
• Flat Blade Screwdriver 1aau.to/obmE/1A...
• Pry Bar 1aau.to/oUM/1AX...
• 19mm Wrench 1aau.to/oW4/1AX...
• 10mm Socket 1aau.to/obdA/1A...
• 17mm Socket 1aau.to/obxG/1A...
• 19mm Socket 1aau.to/oaiQ/1A...
• 32mm Socket 1aau.to/ocN/1AA...
• Brake Caliper Hanger 1aau.to/oi5/1AX...
• Torque Wrench 1aau.to/oaHc/1A...
• Brake Parts Cleaner
• Copper Anti-Seize
• Gloves 1aau.to/oabN/1A...
• Safety Glasses 1aau.to/o4Z/1AX...
• Floor Jack 1aau.to/o7k/1AX...
• Hammer 1aau.to/oUL/1AX...
• Jack Stands 1aau.to/oU5/1AX...
• Punch
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 16

@TRQ Жыл бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@diablo2815 Жыл бұрын

I took the lazy more expensive way out. I bought the loaded knuckle with the bearing already pressed in along with new ball joints.

@aidena6138 Ай бұрын

Please keep doing this, you are educating and helping so many

@TomsCustomCreations 8 ай бұрын

Did you pull this car out of the Pacific Ocean?? So much corrosion! Done well to clean it up

@tiocruz1836 7 ай бұрын

what happened to the knuckle u pressed the bearing into? u installed a brand new knuckle with bearing and hub also when u pressed that bearing in u didn't put any grease on the bearing u installed it dry..... not to mention if I was resusing that rusty knuckle I would've wire brushed it and painted it with some corrosion reducer paint....

@user-vx2kn5dg6i 3 ай бұрын

Anybody noticed that the wheel hub looks brand new at the end 🤔🧐

@panagiotis1519 2 ай бұрын

Once you press (or hammer) out the wheel hub, TAKE OFF THE BACKING PLATE BEFORE you try press out the bearing otherwise you'll damage the plate & the knuckle! I'm so upset I damaged the thing, the bearing would not press out & I had the caliper bracket mounting points flex on the edge while in the press bending the upper mounting. Bad day!

@9er4life67 5 ай бұрын

Thank you, you are a life saver

@Fishing_4_Recovery 9 ай бұрын

Any chance you can make a video of how to change a bearing without a press?

@TRQ 9 ай бұрын

+Fishing_4_Recovery We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-TRQ

@guirochulo 10 ай бұрын

Thanks , really was my solution your video ,

@marvinurgel 3 ай бұрын

I am going to tackle this soon but a little confused on the removal of the sleeve from the old OEM wheel hub. Check out 13:56 , is that step necessary because when you remove the wheel hub, that sleeve if that is what is called will always be stuck with the wheel hub upon removal? if I get both new bearing and wheel hub, I do not need to do this step correct?