√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

Might as well change knock sensors while you're in there

Huge thanks for the video. I was having issues with my 83 burb LS 6.0 swap having to warm up on cold mornings. This made a big difference and improved throttle response. Big thanks.

This video helped a lot until I was torquing the bolts to spec…. Yeah my bolt snapped at 20 lbs…. Googled it and chevy says 8lbs for both the intake manifold and throttle body. I am what you call fucked now.

Very informative and detailed install, I will be doing this work this weekend…

thank you for great video explained perfectly and I plan on doing this job here very soon as well as my dreaded knock sensors as well. apperciate it buddy your videos have saved me so much money doing the work myself with your help.

Thanks for the help man! Followed your videos step by step for replacing my intake manifold gasket and knock sensors. I also cleaned up my throttle body while I was in there

Very well done video! Bravo 🙌

Hey bub thanks for your video glad I saved your video

Very helpful video. Well narrated. Easy to follow.

This is not for 99 to 2003, this is for 2003 and above, which is fly by wire

Excellent instructional video especially detailing the electrical connection removal 👍🏻

Really well done, thanks for putting these out for us. Referenced the video when changing my intake manifold gasket.

What type of tool I will need for the fuel lines

Can i use the fel pro 92211 blue gasket on a 5.3 flex fuel?

These videos are so informative and helpful.

I did all that and my truck won't crank over what did I do wrong???

so i just recently cleaned my throttle body on my 05 gmc sierra 5.3 just because i had no check engine light on for it before so after i cleaned it i installed everything back the right way and did the 3 minute idle re learn well tried now when i turn it on it warms up good but once it warms up it starts to surge the rpm goes up and down then when i put it in reverse or drive it revs up and going into gear or to reverse, when i drive it and give it a little pull to see it it feels good i feel good normal power but as soon as i let go the gas now it stays reved up or accelerated then once i come to a stop the idle kind of goes down like slowly and just starts surging again , i replaced air filter cleaned my maf sensor before my truck wouldn’t do that it would die out coming to a stop though so i would just hold the gas to keep the idle from dropping all the way and stalling the truck but now it doesn’t let me even do that cus when i try it revs up on its own until i drive off and then it feels fine can this be my problem

I have a broken elbow pvc piece that goes into the disconnect of the throttle body at 2:54 seconds to that line broken.. does anyone know the part number or a source i can find that?

where I can buy a Torque like yours

GREAT JOB on this instructional video!! I’m doing this on my H2 soon!!

Well done guys 👍👍👍

Why does it look like the old gaskets are still on when he's re-installing. ;)

What do I do if my throttle body is drive by wire instead of electronic? Also, the plastic engine cover on mine has 2 bolts, one of which is spinning but not loosening. Also, one pipe from my EGR valve runs onto the engine right behind the throttlebody. I have a 1999 silverado 1500 with the 5.3l v8

Now is a good time to clean the intake. Get the injectors cleaned and the fuel line.

I am planning on tackling this on my 2001 Silverado. Are there any other things you would recommend changing while doing the intake gaskets? Thanks

I can't find a video on a Tahoe. Is this similar to one?

So I’m doing it now but the valve to release pressure off the fuel line ain’t running out.

Hello, can I still use these gaskets, if a few of my gasket clips broke off?

At 21:26 he says Dees Nuts, anyone else notice or is it just me?

Great video 👍🏼

Do you guys have a video for a Chevy S 10 doing the same job, on a 2.2L ???

Guess I’ll be doing this seems easier than pulling out the dash and fixing my ac

Just subscribed awesome video

Thank you! ❤

Bolt snapped at 40 foot pounds

Wash that engine PLEEEEASE!!!!

Did this take care of misfire issues?