How to Replace Oil Cooler Lines for 2007-2013 GMC/Chevy Trucks

Рет қаралды 13,977

6 ай бұрын

Hello friends! Today we replaced the oil cooler lines on my 2012 GMC Sierra with the help of a couple could ones. This fix works on all 2007, 2008, 2009, 2010, 2011, 2012, and 2013 GMC and Chevy trucks and full size SUVs.

Пікірлер: 40

@billdelap9757 13 күн бұрын

Thanks!!! You saved me a ton of unnecessary work!

@fixitwithbeer2435 13 күн бұрын

Thanks for watching. Glad the video helped.

@blueridgehunters 4 ай бұрын

I really enjoyed the video, the positivity and the light heartedness. I felt like I was in the garage with you haha. Keep up the great videos!

@fixitwithbeer2435 4 ай бұрын

I am glad you enjoyed the video and thanks for letting me know!!

@BellaRocko 3 ай бұрын

I really enjoyed this video. Well done, sir! And yes, it is the same as in the GMT 800 6.0 trucks as well. The only difference I see is your oil pan drain plug is 90 degrees off-set from the GMT 800. Everything else looks the same. For those asking, you really don't need to drain the oil pan, but make sure you top it off when you're done.

@fixitwithbeer2435 3 ай бұрын

Thanks for the confirmation on the 6.0. I am glad you enjoyed the video. Thanks for the support.

@Badger762 5 ай бұрын

Love your attitude with the work! "This is where you're getting paid" is exactly how I look at these projects. Now, I just need to figure out a good way to drop my front axle, since mine is 4WD.

@fixitwithbeer2435 5 ай бұрын

Thanks for watching. I am glad you enjoyed the video. The 4WD does add a couple of steps. Hopefully you were able to see what is going on this video without the added 4WD components in the way. Good luck!!

@mithical6082 5 ай бұрын

I love this video. It's perfect. Good easy listening music, learning how to wrench on trucks, drinking beer. Doesn't get any better. I hear some guys like to fill the oil filter before putting it on but that's here nor there. Keep on keeping on with your channel! It's great!

@fixitwithbeer2435 5 ай бұрын

Thanks for watching. I am glad that you enjoyed the video. Stay tuned for more.

@dawson91b 3 ай бұрын

Add a few more beers if you’ve got the 4x4 version.

@fixitwithbeer2435 3 ай бұрын

LOL. I have watched a couple of those videos. Definitely increases degree of difficulty. Thanks for watching.

@dawson91b 3 ай бұрын

@@fixitwithbeer2435 Yeah I went to unbolt the line and right away I realized it was going to be a lot more difficult than your experience, but not too bad. The only other steps are take off exhaust manifold heat shield, unbolt passenger side motor mount, loosen strut bolts, drop front differential, and jack the motor up a little. Really enjoyed your video. You’ve earned a subscriber. 🍻

@fixitwithbeer2435 3 ай бұрын

Thanks so much. It is so cool hearing that you enjoyed the video. I am going to check out your vids right now.

@okieninety7613 23 күн бұрын

Facts

@saab9-5 17 күн бұрын

Spray paint them so they dont rust as easy it works pretty well

@fixitwithbeer2435 16 күн бұрын

Great idea. I don’t have much of a rust issue here in Texas, but up North might be a big help. Thanks.

@defontibus 6 ай бұрын

I have the same oil pan, although mine's just full of coolant.

@fixitwithbeer2435 6 ай бұрын

Thomas, I would just drain the coolant and put some Marvel Mystery Oil in there. No one really knows what’s in it, it’s a mystery. Then I would just forget anything was ever wrong and drive normally. Haha. Just kidding. Thanks for watching.

@okieninety7613 23 күн бұрын

Let's see it done with the 4wd now. I've not come across that one for obvious reasons when you go to tackle it

@fixitwithbeer2435 21 күн бұрын

The 4X4 videos I have seen are a lot more intense than this one, but it can be done. Thanks for watching!

@1STSUN5THCHILD 3 ай бұрын

GREAT VIDEO. I HAVE TO DO THIS ON MINES. COULD YOU TELL ME THE NAME OF THE RAMPS YOU USED FOR YOUR TRUCK. I NEED SOME AND I DONT KNOW WHAT ONE WILL HOLD

@fixitwithbeer2435 3 ай бұрын

Thanks for watching. If by ramps you are talking about under the tires, I just use a couple of scrap pieces of 2 X 6. My garage floor and driveway create a little valley. I use the scrap lumber to give me a little more room. No fancy ramps for me. Glad you enjoyed the video.

@Jontfs300 4 ай бұрын

I use wheel bearing grease for the oil filter gaskets

@fixitwithbeer2435 4 ай бұрын

That is a great idea. My Grandpa John introduced me the miracle of wheel bearing grease for installing the vertical thermostat on a 92 F-150. Thanks for watching.

@enricoderojassarson5596 3 ай бұрын

Why did you mention crush washer on oil drain plug? Mine has a rubber o-ring

@fixitwithbeer2435 3 ай бұрын

Interesting. Mine is definitely not an o ring, but I will definitely double check it next time I change the oil and let you know.

@s2klonso138 5 ай бұрын

My issue is cant figure out the exact bolt size to those bolts for replacement without buying new assembly.

@fixitwithbeer2435 4 ай бұрын

Thanks for watching!!

@DrumPeearl 4 ай бұрын

Do I really have to do the oil change at the same time ? I just did mine like 500 miles ago... I have heard that since the filter will have to be taken off I could only loose about a quart. Thanks!

@fixitwithbeer2435 4 ай бұрын

Thanks for watching. On the 2 wheel drive like mine, you really don’t need to remove the oil filter. In the video, I put the new filter on before I swapped the line set. You will lose some oil in the lines, but I would be surprised if it is more than a quart or so. Not sure since I did have the oil out. Good luck. I hope it goes great. Let me know.

@DrumPeearl 4 ай бұрын

@@fixitwithbeer2435 I forgot to thanks you for having made this video ! And thank you for your super quick reply. I am gonna do it on my 2500hd gmc sierra 8.1 Vortec

@fixitwithbeer2435 4 ай бұрын

You are welcome! I am not an expert or professional, but my daughter and I have been having fun making some videos.

@experienceprecision5406 2 ай бұрын

Do you have to drain the oil

@fixitwithbeer2435 2 ай бұрын

I watched a video of a guy that did it without draining. He claimed to only lose a quart in the lines and draining out of the attachment points. Good luck and let me know how it works out.

@experienceprecision5406 2 ай бұрын

@@fixitwithbeer2435 will do. Thank you for replying

@maxwellweiss8007 5 ай бұрын

Is your truck 4x4? I’m about to take this job on and have heard this is much more difficult on 4-wheel models.

@fixitwithbeer2435 5 ай бұрын

My truck is not a 4X4 and it is definitely a harder repair when you have 4X4. There are some videos of different ways to work around the extra hardware. Thanks for watching and good luck with your project.

@s2klonso138 5 ай бұрын

I was able to do it on my 4x4 ,it's doable . Just don't tighten the bolts to much they will snap.

@Justin-cs5cu 4 ай бұрын

It’s way harder with 4x4, the entire front drive train gets in your way. It took me 4 hours today, had to disconnect the front drive shaft and play with the lines a lot. Honestly surprised I didn’t cause the new ones to leak with how much I had to manipulate them to get them around the front drive train and the engine. Don’t attempt this without a second pair of hands and a full day set aside.