How to Replace Rear Drum Brakes 09-19 Ford Fiesta

Рет қаралды 154,561

1A Auto: Repair Tips & Secrets Only Mechanics Know

5 жыл бұрын

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/146/d/brake-drums
1A Auto shows you how to repair, install, fix, change or replace your own worn, squeaky, fading old brakes. This video is applicable to the 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19 Ford Fiesta
This process should be similar on the following vehicles:
2011 Ford Fiesta
2012 Ford Fiesta
2013 Ford Fiesta
2014 Ford Fiesta
2015 Ford Fiesta
2016 Ford Fiesta
2017 Ford Fiesta
2018 Ford Fiesta
2019 Ford Fiesta
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oQn/1AXAA00013
• Impact Screwdriver 1aau.to/o9/1AXAA00047
• Pry Bar 1aau.to/omI/1AXAA00020
• 19mm Socket 1aau.to/otq/1AXAA00043
• Needle nose pliers 1aau.to/ohc/1AXAA00051
• Needle nose pliers 1aau.to/ohc/1AXAA00052
• Side Cutters
• T40 Socket
• 1/2 Inch Breaker Bar 1aau.to/oeG/1AXAA00078
• Ratchet 1aau.to/oTP/1AXAA00016
• Socket Extensions 1aau.to/oPT/1AXAA00015
• Torque Wrench 1aau.to/ozX/1AXAA00044
• Anti-Seize Grease
• Brake Parts Cleaner
• M8x1.25
• Rust Penetrant
• Floor Jack 1aau.to/oo2/1AXAA00068
• Hammer 1aau.to/onM/1AXAA00091
• Jack Stands 1aau.to/onE/1AXAA00065
• Wire Brush 1aau.to/oeL/1AXAA00079
Subscribe: / @1aauto
Check out our playlist:
2011-2019 Ford Fiesta 6th Gen: • 2011-2019 Ford Fiesta ...
Ford Auto Repair Videos: • Ford Auto Repair Videos
For More Info visit us at 1aau.to/h/97/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 123

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@autoSRI 3 жыл бұрын

It doesn’t matter how good you are or how many times you have done it,drums are always a fight from start to finish

@chemistry636 4 жыл бұрын

Great explanation. Great camera angle. Very good detail. Great that you left in when things did not go right first time; that is exactly what many diy mechanics come to realise when they do jobs on their cars. Great video.

@1AAuto 4 жыл бұрын

+chemistry636 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com

@Altersky0512 3 жыл бұрын

She is awesome...I struggled on one side for an hour and got super frustrated...then after watching her do her thing I got the other side done in 10 minutes!!!

@1AAuto 3 жыл бұрын

+Juan Luna Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

@afdave7 3 жыл бұрын

Wow. Incredible video. A++ on the technician work. And A++ on the instruction. And the camera work as well. This video giving me the confidence to try this job. Thank you. Very impressive mechanic work here!!

@richardmineau6755 22 күн бұрын

I found this video to be excellent help and I followed everything she said to do ! She knows EXACTLY what she is doing and she is an expert ! Thank you so much for helping me do my brakes !!!

@joahsark3421 5 жыл бұрын

Everything you could want to know in one video. This is fantastical informative.

@1AAuto 5 жыл бұрын

+Joahs Ark Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com

@JC-zi8qc 3 жыл бұрын

Hi, really found this video useful. Agree that with brakes it is a good idea to do one side at a time, so you can use the other side for reference. Also I take a few photos on my phone showing where each spring fits.Great that you are willing to show that refitting the brake springs can be 'fiddly', reassuring that I am not alone in finding this job patience trying! Keep up the good work!

@1AAuto 3 жыл бұрын

+J C Thanks for the feedback!

@TheRealXyzven 5 жыл бұрын

She's got some GREAT advice!! Love it. Love the sound effects of the "bad cylinder leaking brake fluid" LOL

@1AAuto 5 жыл бұрын

Thanks for checking us out. 1aauto.com +Dunc P

@thebrotherslunn4783 2 жыл бұрын

Thank you I just did my rear brakes the way you teach is beautiful and so are

@RPG-oh1yf Жыл бұрын

Thanks for this. I fought the first one for 30 minutes before finding your video. Took 2 minutes to assemble after.

@stephenmcmanua6251 2 жыл бұрын

thank you thank you thank you, began to bleed my brakes and discovered my drum cylinder had failed, had your video playing to take it all apart(changed the cylinder) and replaced the shoes after cleaning the drum. Would not have had a hope without your video

@1AAuto 2 жыл бұрын

+stephen mcmanua Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

@colmoconghaile7732 3 жыл бұрын

Excellent tutorial , skill and methodology , go lady. 👏

@jimmyzoom1143 2 жыл бұрын

You must be amazed that a woman is able to do this

@patricknoone4773 2 жыл бұрын

Excellent, one of the best I've seen. Thank you very much.

@claireb8542 3 жыл бұрын

Thank you for the really helpful video. I couldn't help but laugh when you said "Sorry you had to witness that" @ 16.13

@BigEightiesNewWave 3 жыл бұрын

the old back-up pumping brakes style adjuster , bringing back memories of my 1964 Chevy Biscayne.

@Noobnuker1 11 ай бұрын

oh boy, i cant wait to do this for myself (cries internally) Thank you for the video though. I dont know what id do without you.

@1AAuto 11 ай бұрын

+niffum Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@spannerssockets6308 4 жыл бұрын

Good presentation! The biggest hassle getting a brake drum off is due to the shoes wearing a lip on to the side nearest the back plate and the shoes having auto-adjusted out so the lip drags the shoes when you try to pull the drum off. Best, if accessible, to slacken the auto-adjuster to pull the shoes in away from the drum so it can pull off with a few taps of the hammer. Test foot and handbrake with help of someone in the driver's seat, wheels of the deck, before starting the brakes service to see if both work and the wheels spin freely with the brakes off. What anti-seize grease product do you use?

@JohnDoeGemany123 5 жыл бұрын

Great work! Really helped alot for the brake change (EU version of fhe Fiesta is the same) Thanks!

@1AAuto 5 жыл бұрын

Thanks for checking us out! +JohnDoeGermany

@TheGazza636 Жыл бұрын

Got me self a bit confused with the springs and adjuster but watched this step by step and bosh it was done Thanks great mechanicing

@i.c8358 5 жыл бұрын

Extremely helpful. Thank you!

@1AAuto 5 жыл бұрын

+I. C Thank you for your feedback!

@bonfacemasharia5843 2 жыл бұрын

Hey guys, If you noticed how incredible smart these guys are hit a like, Let's be good to them

@tommydeforest6510 5 жыл бұрын

Thank you for the awesome video. Can you please describe the adjusting method you briefly mentioned about driving in reverse in a parking lot? I can't find anything online about it

@mrjosh992 3 жыл бұрын

Did you find this anywhere online?

@jameslaiola4976 3 жыл бұрын

Incredibly helpful video. I sincerely appreciate the information.

@1AAuto 3 жыл бұрын

+James Laiola Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@markallen5839 3 жыл бұрын

Nicely done and well explained

@scott5185 8 ай бұрын

As always, you are truly amazing! Thank you!

@jug3r295 2 жыл бұрын

I just did my rear brakes on my fiesta but i want to know if there is any adjustment for handbrake ? because mine is not working at all and all my cables are working good.

@mixedboi 2 жыл бұрын

This technician, she's awesome. Pro job.

@MonicaGonzalez-ei1zf 3 жыл бұрын

Is this the same for a 2013 ford focus se? thanks!

@mikeg5951 7 ай бұрын

Great video! Thank you very much!

@flunul 2 жыл бұрын

Great video. Thanks from Sweden.

@1AAuto 2 жыл бұрын

+Ulf Lundqvist Thanks for the feedback!

@bwright5520 Жыл бұрын

VERY VERY HELPFUL THANKS

@whiskersthecat8124 2 жыл бұрын

At Approximately how many miles would you change the rear drum breaks?

@ibo1137 3 жыл бұрын

Thanks. Really good video.

@1AAuto 3 жыл бұрын

+IM26C4U Thanks for checking us out! 1AAuto.com

@JohnGarcia-be9el 3 ай бұрын

14 an did it easy peasy lemon squeezy this video was very good

@user-my9ht3gb9d 9 ай бұрын

Thanx for good giude. My problem is now, that my shel do not fit after I change the brakes... Do i do something wrong?

@johncollins8304 2 жыл бұрын

"It's almost like I knew what I was doing" !! Great to see even a professional with years of experience doesn't find these a piece of cake 🍰. For someone who does this maybe once in five years it sure is a challenge. have spent TWO DAYS on mine, and still not finished. Got one side on. Second side, can't get the drum on. The diameter of the fitted shoes on the good side is 200mm, on the no-go side it's 5mm more, a few mm more than the i.d of the drum. Have dismantled them both again to compare and see if there is a machining error. Not that I can see. I notice that the top of the shoes are not pushing the sides of the piston in and yet the long spring pulling them both together where you had to shift it over even further (!!) was sooo hard to stretch. The rubber on the piston ends is kind of proud and you can see the pistons but it should be like yours with the rubber going in and hiding the pistons.... All ideas welcome on this my THIRD day! Thank you.

@dylantherrien1053 6 ай бұрын

Amazing vid thanks

@samb1097 2 жыл бұрын

For anyone wondering this process is very similar for the Ford Focus MK3

@strigon46 4 жыл бұрын

Awesome video! Is it the same process with a 2011, 1.2 l, ford fiesta hatchback?

@1AAuto 4 жыл бұрын

+strigon46 Yes, it should be the same or a similar procedure.

@tommydeforest6510 4 жыл бұрын

Can you reply to my comment or you dont know?

@DropDeadLegs 4 жыл бұрын

Looking for more info on that e/parking brake adjustment with hand brake that she mentions please.

@mrjosh992 3 жыл бұрын

Did you find anything on this?

@rtz549 3 жыл бұрын

In theory; every time you use the parking brake; it adjusts the brakes to compensate for pad wear.

@simangadladla9330 3 жыл бұрын

Thanks so much . My drum can't rotate but once I removed the brake fluid pipe it's rotates ? What could be the problem . It's a ford fiesta 2011 model

@cmrnx 3 жыл бұрын

could be a sticky/ partially seized wheel cylinder and when you disconnect the brake line it releases the brake fluid behind the cylinder decreasing the force behind the cylinder which allows it to slightly retract itself releasing the shoes from the drum. The reason it is sticking when the brake pipe is connected is because if the cylinder is sticky anyway it will have a hard time retracting itself as it’s getting partial stuck. If you then have the pressure of the break fluid behind the cylinder as well, it will have an even harder time retracting itself due to the pressure of the fluid acting against it causing the shoes to remain pressed against the drum locking up that wheel.

@devmobray 3 жыл бұрын

Awesome stuff. These old drum brakes are a royal pain in the ass to change with all their stupid finiky small clips and springs & such- its a good time.

@lascar48 4 жыл бұрын

A good job well done.

@1AAuto 4 жыл бұрын

+lascar48 Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

@henrycruz45cal 5 жыл бұрын

Great job ma'am

@1AAuto 5 жыл бұрын

+Henry Cruz Thanks for checking us out. Shop here for high quality auto parts: :1aau.to/m/Shop-1AAuto-c

@mandowhite4574 Жыл бұрын

Good video

@ordinaryosprey2661 Ай бұрын

Hit the outside rubber to pop it off it gives you more leverage and no your not going to shoot the tire and wheel across the shop with a small mallet or either one by themselves for that matter the lug nut is just to keep it from falling

@michaelhacker4357 4 жыл бұрын

Great Job...

@1AAuto 4 жыл бұрын

+Michael Hacker Thanks for checking us out. 1aauto.com

@kimquyluu6771 Жыл бұрын

Thank you share clip

@Vredeopaard 3 ай бұрын

Thanks allot 😊😊 now i can do it self

@1AAuto 3 ай бұрын

+@bless1156 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

@richardburns5925 4 жыл бұрын

Great video and advice, the best tip there is leave other side on as reference, every time. Similar to when changing drive belt/serpentine belt that drives all ancillarys, you think you can memorize it's position, when you try and fit new belt......hmmm.....it just won't go! Easy, take some photos of belt before removing, it will help!👍

@daniel.a.r89 3 жыл бұрын

Good job

@user-xv3en9pg7c 3 жыл бұрын

Good Job!

@1AAuto 3 жыл бұрын

+ΘΕΟΔΩΡΑ ΚΑΛΥΒΑ Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@nicholasvonrhine541 5 жыл бұрын

Outstanding.

@1AAuto 5 жыл бұрын

+Nicholas Vonrhine Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c

@runigturtle1209 10 ай бұрын

Does anyone know if there is a disc brake conversion kit for the fiesta 2011

@Subjohny 2 жыл бұрын

The easiest way is to assembly all parts on the floor and put whole assembly on! This way you will not struggle with springs! Also its good idea to grease both ends of break piston

@darvis111 4 жыл бұрын

mines a 2014 and it does not have the torque screws holding on the drum?

@brianiswrong 4 жыл бұрын

Won't matter,the wheel nuts hold.the drum on,the torque screws just were designed for bolts really,so the drum would stay still and the bolt holes line up when refitting the wheel.

@caphillres 3 жыл бұрын

Part number for the drum hardware kit? I can't find it on your website.

@1AAuto 3 жыл бұрын

+Chris Sweeting I would be happy to look it up for you what is the year, make and model?

@beachbum6741 8 ай бұрын

You go girl!

@user-vx9wx2li1r 19 күн бұрын

well done lady

@Vredeopaard 3 ай бұрын

Who else close his eyes when she spraying break cleaner😂😂

@bonfacemasharia5843 2 жыл бұрын

I like her, She's honest and real, As a technician I know how hard that shut can get, Am telling you

@otm646 6 ай бұрын

6:22 Push a 10mm nut driver over the pin to compress the flat spring then pull with pliers.

@nikolasgarcia1868 2 жыл бұрын

awesome video just do to the fact it didnt go 100% at first those pins and springs a nightmare lol

@user-vx9wx2li1r 19 күн бұрын

well done gal

@jimmyzoom1143 2 жыл бұрын

Everyone is so thrilled how good this video. Its changing brake pads. That's it. Or is ut because its a woman, omg it's a woman

@toozizzle550 Ай бұрын

Yep I'll be paying some to do those 😁😁

@jeenkzk5919 4 жыл бұрын

I was going to change my own shoes BUUUUUUUUTTTT I may just save the heartache and just have someone do it. Disk break pads are a cinch one you figure it out! My first time I changed pads was on an 89 Cadillac El Dorado. I didn’t know what I was doing and I figured it out. The only thing I needed to know was to push in the caliper with a C clamp so I can put it back on.

@1AAuto 4 жыл бұрын

+Jeenkz K Thanks for checking us out!

@barberdoug6930 2 жыл бұрын

I need a wife like her. Great Job!

@bigtie28 5 жыл бұрын

Nice job though

@trapperbt 3 жыл бұрын

When I see a qualified experienced mechanic handle the small details and annoyances with confidence I wonder why I ever try this at home. I used to enjoy working on cars but I dont love her anymore. lol Oh great job thanks

@MrBoehol 3 жыл бұрын

Its much easy to do the work if you remove the hub with bearing first.

@1AAuto 3 жыл бұрын

+Björn Holmgren Thanks for the tip!

@UnderGr0undErnie 3 жыл бұрын

Good video for cars 10 years old, but this does not cover Fiesta 2018 onwards, its a totally different auto adjuster inside the drum.

@g.c.9904 3 жыл бұрын

She's great.

@1AAuto 3 жыл бұрын

+G. C. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@littlereptilian7580 11 ай бұрын

You saved me girl

@goodolddoug889 3 жыл бұрын

I noticed at the end of the video that this Fiesta is suffering from the same thing that happened to my 2011 SES. That @#$@ing wheel well lining in the rear rips up because it's made of material instead of plastic. What happened to me was that in the dead of winter I was driving 80kph (roughly 50mph) on the highway and suddenly the rear right of the car bounced up and I almost lost control. Turned out, a big chunk of ice was stuck to the lining and the weight finally ripped it, causing it to fall all over the wheel. The ice then must've gone under the wheel and dragged a chunk of the lining with it. That shit reached its limit and ripped off, but not before bouncing the car dangerously on a snowy road. If you own a Fiesta and live where it gets snowy and icy in the wintertime; do yourself a favour and rip those linings off. They're useless and potentially dangerous.

@amandawillox2212 2 жыл бұрын

Great video but using cutters to set the spring!? Not a good idea! Risk cutting or notching the spring!

@shreeranjit9683 3 жыл бұрын

I have a ford fiesta 2012 model. I have a problem where the break adjuster keeps falling between the break pad and the drum. it jams the tires. So, I want to know why it keeps falling like that. Can you send me your email address so that I can show you what it looks like.

@1AAuto 3 жыл бұрын

+Shree Ranjit We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@GJ-zy8bc 2 жыл бұрын

Proper tool for the job would have made this job so much easier. Using diagonal cutters to change springs is a big no no!

@alandew9372 Жыл бұрын

Great video. But I would wear a dust mask when wire brushing any area around brakes, (Asbestos dust does not take prisoners)

@thomascalvert7894 3 жыл бұрын

Excellent,thought the mechanic should have worn a face mask to give protection from brake dust,but apart from that the video is 5tar,Thankyou

@BigEightiesNewWave 3 жыл бұрын

Cars back there look like they were driven under the sea. Rust/barnacles.

@brandonalloe-xy1ci 10 ай бұрын

I wouldn't recommend ever getting brake parts cleaner on rubber because it will cause premature failure.

@itisollieb6433 Жыл бұрын

How can a wheel be this stuck😂

@BigEightiesNewWave 3 жыл бұрын

Or take a pic on your phone before you start.

@mfawzi89 2 жыл бұрын

Why is it so complicated for the rear breaks??? Car manufacturers are so silly

@bigtie28 5 жыл бұрын

First

@TheDradge 3 жыл бұрын

It's not an "e-brake" or emergency brake. It's a parking brake.

@brandonalloe-xy1ci 10 ай бұрын

Drum brakes are terrible.

@yuezhang2526 4 жыл бұрын

what a rust bucket of a car