How to Replace Rear Sway Bar Link 03-11 Honda Element

No video

How to Replace Rear Sway Bar Link 03-11 Honda Element

Рет қаралды 20,041

1A Auto: Repair Tips & Secrets Only Mechanics Know

Күн бұрын

Buy Now!
New Sway Bar Link from 1AAuto.com 1aau.to/ia/1ASF...
In this video, 1A Auto shows you how to remove, replace, and install a sway bar end link. This video is applicable to 03, 04, 05, 06, 07, 08, 09, 10, 11 Honda Element
🔧 List of tools used:
• 15mm Wrench 1aau.to/oki/1AX...
• 19mm Socket 1aau.to/omN/1AX...
• 1/2 Inch Breaker Bar 1aau.to/ohv/1AX...
• Ratchet 1aau.to/oZw/1AX...
• Socket Extensions 1aau.to/oN5/1AX...
• Torque Wrench 1aau.to/opZ/1AX...
• Rust Penetrant
• 5mm Hex Wrench
• Floor Jack 1aau.to/oos/1AX...
• Jack Stands 1aau.to/ooB/1AX...
For More Info visit us at 1aau.to/h/aIc/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 16

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@kwsbike 5 жыл бұрын

service manual has a torque of 29 ft lbs on the self-locking nuts, applied after the weight of the vehicle on the suspension.

@elizabethf8078 Ай бұрын

That's one RUSTY undercarriage. I'm guessing y'all are on the coast.😂 Thanks for all the Element videos!

@orificium 4 жыл бұрын

The OEM rear sway bar links on my 2003 Element had 14mm nuts on them. I'm replacing them with MOOG links that have 15mm nuts and grease bushings. The OEM links with the allen key part in the center of the threaded bolt is a terrible design. Rusted out and stripped right away and threads were so bad, I had to cut them off with a sawzall.

@billybradford Жыл бұрын

Great video, thanks so much!

@8325A 11 ай бұрын

Do you have to align the car after you replace this?

@tomsmith4753 5 жыл бұрын

Thank you! Should you use thread lock on the bolts? Just wondering.

@1AAuto 5 жыл бұрын

+Tom Smith You are welcome and for parts then need to be serviced or replaced shouldn't need Locite Red or any thread lock since you will have a hard time replacing it down the road.

@mattfoley6082 5 жыл бұрын

Learn from my misery. Don't waste time unscrewing the old one off, it's not worth the time. Just cut the old nut and bolt off with a recip. saw. They'll be rusted on and difficult to impossible to remove without destroying the old link.

@carbonpictures 5 жыл бұрын

good idea- Im getting ready to do this tomorrow, and I just bought a new package of metal blades last week!

@viel.anthony 4 жыл бұрын

Tried doing mine this morning, the angle on the bottom nut is garbage, I can't retorque the new link because the subframe is in the way... Now the car is stuck on jack stands.

@rocs209 4 жыл бұрын

Can I do this with car ramps?

@joehyundaitech7961 5 жыл бұрын

grate job but when you do theses every day at a dealer ship shop I could not keep doing it with hand tools at 53 years I use my battery powered ratchet or air ratchet much faster and less stress on the body