How to Replace Rear Wheel Bearings 1999-2004 Jeep Grand Cherokee

Рет қаралды 12,714

7 ай бұрын

Buy Now!
New Wheel Bearing & Seal Kit from 1AAuto.com 1aau.to/ia/1ASHS00992
This video shows you how to install new rear wheel bearings from TRQ on your 1999-2004 Jeep Grand Cherokee. If you hear a grinding or groaning noise while your vehicle is rolling, it might have a worn out wheel bearing. A worn bearing can allow the wheel to wobble, creating a host of other issues. To save yourself from more headaches down the road, replace your bearing right away. For solid rear axles, you'll need to replace the axle seal too.
This process should be similar on the following vehicles:
1999 Jeep Grand Cherokee
2000 Jeep Grand Cherokee
2001 Jeep Grand Cherokee
2002 Jeep Grand Cherokee
2003 Jeep Grand Cherokee
2004 Jeep Grand Cherokee
Tools you will need:
• Pry Bar 1aau.to/o2p/1AXAA00020
• 14mm Socket 1aau.to/obL3/1AXAA00015
• 18mm Socket 1aau.to/oasM/1AXAA00043
• 19mm Socket 1aau.to/oasM/1AXAA00043
• 8mm Socket 1aau.to/obqE/1AXAA00017
• Brake Caliper Hanger 1aau.to/okv/1AXAA00439
• Cutoff Wheel 1aau.to/oau/1AXAA00254
• Press
• Slide Hammer
• Pliers
• Ratchet 1aau.to/obQD/1AXAA00016
• Torque Wrench 1aau.to/oaUg/1AXAA00044
• Cloth Rags 1aau.to/oHD/1AXSS00035
• Gear Oil
• Gloves 1aau.to/oazq/1AXSS00048
• Rust Penetrant
• Safety Glasses
• Chisel 1aau.to/omB/1AXAA00055
• Drain Pan
• Floor Jack 1aau.to/oaib/1AXAA00068
• Hammer
• Wheel Chocks
• Wire Brush 1aau.to/ovE/1AXAA00079
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 19

@TRQ 7 ай бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@russellhart2006 Ай бұрын

Very useful video I was chuckling at all the nice new shiney parts with new nuts, no fighting 20 year old rust

@user-hb4nf8wy4k 2 ай бұрын

I watched 3 videos on this all from you. In the last vid I watched I mentioned hoping you did a vid on the bearings. Now I'm prepared. Thank you and I'll sub for sure. Good work.

@josedecruz4580 Ай бұрын

Thanks for the info I'll be coming back and reviewing the video for when I start my change

@ThePLWarrior 3 ай бұрын

That notch is for the parking brake cable

@farmerbrown1978 6 ай бұрын

This was the video I needed. Thank you.

@tpb1717 13 күн бұрын

I had this done recently and I'm trying to figure out how I can tell if they actually did the job, what's the easiest way to tell?

@katrosper Ай бұрын

awesome vid

@mechsupernova Ай бұрын

What happens if you put the bearing in backwards? Looks like the whole bearing would come out at one time.

@durantplayz7111 Ай бұрын

Would a 6 ton press beable to push the the bushing enough

@stephvanschalkwyk6866 4 ай бұрын

How long do these bearings last? Is it worth it to just buy the entire assembly?

@caseycallahan8767 2 ай бұрын

The ''race'' is the ring that holds the bearing on. What he calls the race is the bearing ''cup'' Sure wish they'd use proper names for components. Bearing races used to have set screws that held them to the shafts on machinery. You can heat the race and then just tap it into place and when it cools it will be tight just like installing a ring gear on a flywheel.

@user-db7xs4qg5s 7 ай бұрын

Где вы берёте такие ржавые тачки? У меня GMS Envoy 2003 года, вообще как новый снизу.

@user-pr6tj9qy6s 6 ай бұрын

"Hi, why do you use a different wheel bearing when pressing it in, as initially shown in the video?"

@DAWSONKAiN Ай бұрын

Why my man right here tell me 70 ft lbs for the caliper bolts on all the brake videos 🤔

@danielrawlings9927 16 күн бұрын

2:30 "grab your rotor, wiggle it off, and set it aside." THATS NOT HELPFUL TO THE MAJORITY OF THE POPULATION 😂😂😂 Most peoples rotors are gonna be pretty jammed on there and just saying "okay now take this piece off" isn't helpful at all.

@caseycallahan8767 2 ай бұрын

What's with all the rubber gloves these days? Have mechanics gotten so wossified they can't get their hands dirty?