How to Replace Right Rear Wheel Bearing & Hub Assembly 2006-2013 Chevy Impala

Рет қаралды 31,883

Күн бұрын

Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com 1aau.to/ic/1ASHR00074
This video shows you how to install a new wheel hub and bearing on your 2006-2013 Chevy Impala. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This process should be similar on the following vehicles:
2006 Chevrolet Impala
2007 Chevrolet Impala
2008 Chevrolet Impala
2009 Chevrolet Impala
2010 Chevrolet Impala
2011 Chevrolet Impala
2012 Chevrolet Impala
2013 Chevrolet Impala
Tools you will need:
• Flat Blade Screwdriver 1aau.to/ob/1AXAA00013
• Pry Bar 1aau.to/ob/1AXAA00020
• 10mm Wrench 1aau.to/ob/1AXAA00010
• 13mm Socket 1aau.to/ob/1AXAA00015
• 14mm Deep Socket
• 14mm Socket 1aau.to/ob/1AXAA00015
• 19mm Socket 1aau.to/ob/1AXAA00043
• Brake Caliper Hanger 1aau.to/ob/1AXAA00084
• Hub Puller
• Slide Hammer
• Needle nose pliers 1aau.to/ob/1AXAA00051
• Needle nose pliers 1aau.to/ob/1AXAA00052
• T30 Driver 1aau.to/ob/1AXAA00008
• T30 Socket
• Ratchet 1aau.to/ob/1AXAA00016
• Torque Wrench 1aau.to/ob/1AXAA00044
• Brake Fluid
• Brake Grease
• Brake Parts Cleaner
• Cloth Rags 1aau.to/ob/1AXSS00035
• Copper Anti-Seize
• Paper Towels 1aau.to/ob/1AXSS00035
• Rust Penetrant
• Center Punch 1aau.to/ob/1AXAA00055
• Hammer 1aau.to/ob/1AXAA00091
• Pick 1aau.to/ob/1AXAA00037
• Rubber Mallet 1aau.to/ob/1AXAA00413
• Sledge Hammer 1aau.to/ob/1AXAA00091
• Wire Brush 1aau.to/ob/1AXAA00079
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 11

@TRQ 2 жыл бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@jameszond8805 7 ай бұрын

This video sure made my job real easy thank so much

@bsrcat1 Жыл бұрын

I got a 2011... It does not have drum brakes on the rotor. The emergency/parking brake cable is on the caliber. The hub is the same though and the rotor is different 🤷.

@waynerobichaud3967 7 күн бұрын

What if you can't rotate the hub due to its frozen

@mitchmurphy7791 11 ай бұрын

I'm also looking for the brake backing plate I got a 2009 and the only place they say I can find is a dealer can't even find a part number

@KS-dg5zh Жыл бұрын

Im trying to find a right rear backing plate for this same setup. Says it discontinued. Any ideas where to find. Part # 2010 impala with e brake shoe

@kennycovington7046 5 ай бұрын

You never told how to remove the emergency brake cable ???

@TheSrvsoldier1 9 ай бұрын

You don’t have to take half that stuff off

@TRQ 9 ай бұрын

+Lance Ragan We appreciate the feedback. Sometimes there are multiple ways to accomplish the same repair. 1aau.to/m/Shop-TRQ

@foxxfury145 10 ай бұрын

I feel like you.dont need to take off half that stuff

@dootieflack 2 ай бұрын

Guy in video has never done this before. You started hammering before the brake parts were off.... it will never come off like this. Brake parts must come off first.