How to replace the drum brakes Clio mk4 🚗

Рет қаралды 48,151

Күн бұрын

BUY THE AUTO PARTS you need for the operation : 👉 bit.ly/cheapAutoparts 👈
📱 DOWNLOAD THE APP : 🍎 bit.ly/MCD12AppStore, 🤖 : bit.ly/MCD12PlayStore 📱
⬇︎⬇︎ 🔥 🔧🔧🔧 🔥⬇︎⬇︎
🛠📏⚙ FIND ALL THE PARTS AND TOOLS NEEDED AND RECOMMENDED BY USETOOL EN ⚙📏🛠
Needed parts:
- Brake cleaner : bit.ly/brakecleaneren
- Drum brakes : bit.ly/brakekit010201EN
- Copper grease : bit.ly/coppergreaseen
Discover a vast array of services that will help you run the maintenance of your car: vehicle user manuals, maintenance planning and mechanics-oriented tutorials!
Drum brakes on a Renault Clio mk4.
Discover the world of UseTool EN
Needed tools:
-💣🤖🏆The complete toolbox recommended by UseTool EN to repair your Clio mk4 : maclede12.co/toolboxCLASOS3050en 🏆🤖💣
- 32mm socket
- Big flat head screwdriver
- Large socket wrench
- Socket wrench
- 8mm spanner
- Sanding paper
- Wheel lug wrench
- Torque wrench : maclede12.co/torquewrenchCLAS... or maclede12.co/torquewrenchCLAS... or maclede12.co/torquewrenchCLAS...
- 10mm socket
- Lineman's pliers
- T-handle wrench
- Liquid collector
- Hammer
- Wire brush
🔝💪Safely lift your Clio mk4 with the hydraulic jack: maclede12.co/jackCLASOH5304en and axle stands: maclede12.co/standsCLASOM3030en recommended by UseTool EN 💪🔝
- Hydraulic jack
- Wooden peg
- Axle stand
🚗📢💡 RESOURCES 💡📢🚗
Usetool's warnings
- Before starting, relase the hand break otherwise the operation will be impossible.
- When replacing the rear drum brakes, it is best to replace the brake cylinder, key part in the good operating of the system.
Usetool's infos
After having change the drum brakes, it is vital to purge the brake fluid in order to remove any bubbles that have infultrated the circuit.
📽❤️🚨 USEFUL VIDEOS 🚨❤️📽
- [ USETOOL'S TIPS & TRICKS ] DIY: Making a liquids collector : • ASTUCE : Fabriquer un ...
- [ USETOOL'S TIPS & TRICKS ] Lifting your vehicle safely : • ASTUCE : Soulever son ...
- [ USETOOL'S TIPS & TRICKS ] Removing and reinstalling a wheel : • ASTUCE : Pneu crevé ? ...
Space Race by tubebackr | / tubebackr
Music promoted by www.free-stock-music.com
Terms and conditions of the offer : www.mister-auto.co.uk/operati...
Disclaimer: This video was created for information purposes and does not guarantee the outcome of actions undertaken.
To ensure that you see the best results, we recommend getting in contact with qualified technicians who will carry out the installation.
This video provides tips and recommendations that can be useful when repairing or changing parts. MCD12 and its partners cannot be held responsible for any physical and material damage that comes from the poor installation or incorrect interpretation of the video content.
This video was created for information purposes and does not guarantee any outcomes. The user is solely responsible for the incorrect use of repair machines, tools and parts, in particular if these may cause physical damage. MCD12 and its partners recommend taking great care and carefully following the safety rules when carrying out the repair or replacement of any parts. Please keep in mind that using poor quality parts compromises the safety of the driver when on the road.
0:00 Intro
0:11 Remove the drum brakes
5:22 Set the new drum brakes up
5:35 Install the new drum brakes

Пікірлер: 26

@UseTool_EN 3 жыл бұрын

BUY THE AUTO PARTS you need for the operation : 👉 bit.ly/cheapAutoparts 👈 📱 DOWNLOAD THE APP : 🍎 bit.ly/MCD12AppStore, 🤖 : bit.ly/MCD12PlayStore 📱 ⬇︎⬇︎ 🔥 🔧🔧🔧 🔥⬇︎⬇︎

@pateril Жыл бұрын

Great video - although I had to use a 36mm socket to get the axle nut removed.

@Nectarie1986 Жыл бұрын

Good job!!!You explain very well!👍

@MarkWright-ms3dz 3 ай бұрын

Great step by step guide 👍

@williamdevereux9086 Жыл бұрын

For anyone's information, I have a 2014 Clio DCI 90 Eco S&S trim and the nuts are 30mm on the rear drums so it may be different depending on the year and model

@serkankaya6230 6 ай бұрын

Very good man

@UseTool_EN 6 ай бұрын

Thanks a lot @serkankaya6230 ✌ Hope the operation went well 👌

@derekmitchell1730 2 жыл бұрын

Wish I had read the comments about the hub nut before starting work rather just trusting the video, the video really needs updating to say its a 36MM socket, as Ritchie has said most socket sets only go up to 32MM so I have to wait now for the correct socket to arrive which is a bit of a pain since it was a nightmare trying to get the hub cap/cover off. My Renault is a Clio 4 2018 model.

@derekmitchell1730 2 жыл бұрын

I should of added thank you for the video even with the error it was very helpful to me.

@attilaszakal 10 ай бұрын

Exactly the same happened to me

@afshinyousefzamani1564 6 ай бұрын

Hi... What size mm of socket wrench?

@alexandrosk.6451 Жыл бұрын

The video says to use 280Nm in the torque wrench when tightening the nut of the drum. Are you sure if this is correct, because it appears to be too high? What does the manufacturer suggest for Clio IV for the drums in the rear axle? Thanks

@SmAEsch0R 2 жыл бұрын

please make a video how to change the drum brakes on a peugeot 207 !!

@stevejohnman68 Жыл бұрын

Is there no adjustment needed to bring shoes out a little so you can let handbrake adjustment off a bit . And the hub nut is more than 21mm!

@user-tb5ko2go1c 6 ай бұрын

Thank you for that

@UseTool_EN 6 ай бұрын

Hi @user-tb5ko2go1c ! My pleasure, I hope the operation went well 👌

@pauljeffreys7223 Жыл бұрын

Done the brakes today, you will need a 36mm socket and a torque wrench to tighten the hub nut to 280Nm, the wheel nuts 105Nm, 17mm socket. Photos of the spring layout help before you strip it down. Adjust the handbrake afterwards, T20 bit and 13mm ring spanner needed.

@Mr.-Wint 10 ай бұрын

Thanks, - but no locking mechanism for the center nut except the 280Nm ?

@Sven_Re347 5 ай бұрын

And the handbrake adjustment?

@whitewalker9622 4 ай бұрын

If anyone out there have a running issue with their Clio 4 2019(tce90) it might be this! I have tried to get in contact with renault Sweden but still no answer after a week. This might even be a "BIG" recall. The evap valve in my car was mounted up side down from factory. So everyone, look at the blue prints... Allways! Does anyone have contacts with Renault in France?

@leventebaranyi1694 Жыл бұрын

36 mm nuts on a 2016 renault clio grandtour

@robbridgen2726 3 жыл бұрын

Hey guys there’s an error in your video. For removal of the hub nut you state use a 21mm socket, yet when tightening you say it’s a 32mm socket. Which one is it? As far as I am aware it’s the same nut that goes back on so would surely be the same size socket.

@tinblo2621 3 жыл бұрын

Just to add confusion, my Mk4 2014 is bigger than 32mm. I’m here trying to find out the size so I can order the correct socket

@ritchiewallace6242 2 жыл бұрын

It's a 36mm socket, beware normal socket sets only go upto 32mm!

@sleekitwan 2 жыл бұрын

Yes, they are always massive compared to ‘normal’ sizes. (Hot tip first: incredibly common to be able to drive the car, safely, with the plastic middle taken out of the alloy wheel, and the little steel cap sprung out from the drum, per this very good video…you will have to jack the car up, remove the wheel, but these are just dust-caps, so if you are really unsure of the size, you can set yourself up so you try it right outside the parts/tool shop. That way, you definitely got the right size with one shop trip.) Highly unlikely you will have the correct one, unless you specifically bought it…and they like to vary the sizes between models and manufacturers…I have literally stopped work on my car, every single time, because I never have the correct size. I have 37mm, 34mm, and two others. With four oversize in total, it’s now 50/50 I won;t have to halt work. One thing for sure, it ain’t gonna be no 21mm. That’s minuscule in terms of axle nuts. All mine, from Citroen Xm and Rover 827, down to little Renaults, were in the ‘30+’ mm range. 21mm is just a bit bigger than wheel nuts/bolts. Can’t be 21mm for that reason, plus, the actual socket is usually quite ‘deep’, so even if you had a ‘normal’ socket set with say, 34mm in, it is highly unlikely to have enough depth so the axle end permits the serrated profile part of the socket (the front rim that ‘grips’ the nut), to,be accommodated - it’d just foul when you tried to push it on the nut, not reaching a fully tightened nut. It’s a constant PITA, can you tell?! Take care, easiest to measure it first so you;re in the right ball park, and most spares places are fine about you returning it in exchange straight away, if you literally just put it on top of the nut and it’s not quite the right size. Note the hot tip at the start of my reply though, it does usually prove possible!

@sahim333 2 жыл бұрын

Mine is 30mm.