How to replace the front axle on a 2006 Dodge Caravan

Рет қаралды 85,869

9 жыл бұрын

In my video I will take you through the process of replacing the front axle on a 2006 Dodge Caravan .Easy step by step instructions.Nothing left out.

Пікірлер: 116

@unkulmark 7 жыл бұрын

Jim, Thank you for providing this tutorial video. From watching your video (many times!) & a few others I was able to successfully replace the passenger side CV axle on my 2001 Caravan. On mine I also had to remove the 18mm castle-nut to take the tie-rod end out & then remove the 10mm bolt that holds the ABS sensor in place to get it & its wiring out of the way. I also had a Chilton manual to refer to but very seldom did I use it because the videos are much more instructional.

@subarc_ 6 жыл бұрын

Great video Jim. I used it to change both sides on my dad's 2010. Your method of changing them is a lot better then the other ones I found on youtube. Keep up the good work.

@jimbrown9812 2 жыл бұрын

One of the best simple explanations I've seen. THANKS FOR A GREAT VIDEO

@9wire9 4 жыл бұрын

Changed my axle in about 30 minutes after watching this, I was going to bust the ball joints, this is much easier.

@nonregla1 6 жыл бұрын

great instructional video. Thanks so much for sharing your skills and experience.

@richardthompson2606 8 жыл бұрын

wonderful video. direct and to the point start to finish.

@jackhunt7490 2 жыл бұрын

Good job man very informational. I'm getting ready to do this same job on my wife's van in the morning. Awesome refresher

@Fred-xu8zb 5 жыл бұрын

Thanks Jim, easy to follow, and understand. I have a 2005 I am doing some work on, I could have questions, as I go along.

@chcpilot149 8 жыл бұрын

Thank you! Excellent information. Now I feel more confident to do this repair.

@jimthecarguy 8 жыл бұрын

+Chc Pilot Great.If you need any advice let me know.

@jaquelmuckelvene3480 8 жыл бұрын

jim your the man dude, thanks first time job and my confidence level is ouz the roof because of this tutorial

@jimthecarguy 8 жыл бұрын

+jaquel muckelvene Thank you for your feedback.If you need any further advice just ask.

@jackotrades6538 8 жыл бұрын

Great job on the tutorial. I've watched other vids and yours was the best. Thanks for saving me $!

@jimthecarguy 8 жыл бұрын

+Jackotrades I'm happy to share my knowledge.Let me know how your job come out.

@kennygraves5866 9 жыл бұрын

you're video was the 3rd video i watched to do this job and it was very accurate and to the point .thank you very much for you're professional video ..Next job i do i'll look for you're video.....

@jimthecarguy 9 жыл бұрын

***** Thank you for your kind words and your feedback .I hope the job goes Ok for you.If you need and advice let me know.Jim

@70sfred1 2 жыл бұрын

Thank you for a well explained process!

@countrylivingguy5172 6 жыл бұрын

Thanks your video helped me out a lot.

@Antumenes 9 жыл бұрын

Excellent video Jim, Thank you so much!!! It is just the best

@jimthecarguy 9 жыл бұрын

Antulio Meneses Thank you for watching and your feed back

@sly5176 7 жыл бұрын

Great job. just like we did it in School. fantastic.

@phillipbegay2837 3 жыл бұрын

That was cool the way you explain. I'm no mechanic but thank you showing your video.

@weskarcher483 5 ай бұрын

That's fairly easy. This part will help me pull back the transmission to replace leaky freeze plugs on the back of the block. Engineers didn't think when they placed them there.

@izzycamaro 2 жыл бұрын

Great instructional video. Thanks a lot.

@youcanfixit3721 2 жыл бұрын

I love it! Working late to make us this video... Thanks

@MasterScreenPrints 8 жыл бұрын

great video, I need to replace mine. do you have a video for the back shocks? I have a 05 town and country. same thing as dodge.

@randywells9676 Ай бұрын

I found using adjustable oil wrench, duct tape handle worked the best on drive side, the lip y'all are using to pry is SO THIN, I just walked the handles and couple hits fluid started to leak so I was making progress, I did same thing on pass side but didn't need tape being the lip was MUCH larger and POP came out, only took about 1.5-2 hours on the ground with jack stands

@markjamesbreeze9572 8 жыл бұрын

Thanks mate well done big help !!!!

@jimthecarguy 8 жыл бұрын

+Marc Breeze I'm happy to help

@keithnoneya 9 жыл бұрын

Did this on several vehicles and never pulled the Struts because that would require a front end alignment. Why not just pull the lower ball joint, outer tie rod end and the ABS speed sensor then swing it out of the way. (To make it easier pull the Brake Caliper, Guid Plate and Rotor). Pull and replace the axle, do the reverse installation. Job done in for both sides in 3hrs, and no front end alignment needed! Best Wishes/Blessings Keith

@GTTeancum 8 жыл бұрын

Thanks VERY much for the video. My 2008 Caravan was slightly different. If you have a 2008-2010 Caravan/Town & Country watch this video first, then Google "allpar Replacing a 2008-10 Chrysler-Dodge minivan half shaft" to learn the differences. The author of that article is Jeremy Schrag.

@friendsofinjuredride 9 жыл бұрын

Thank You for your time , You did good

@jimthecarguy 9 жыл бұрын

Tony Reichart Thank you for your feedback

@kel5194 2 жыл бұрын

Thanks for the video. Is the procedure the same for the passenger CV? mine is also a 2006 G Caravan. The passenger side is a much longer axle so just curious if comes out all in one piece or does it have to be separated?

@scottsodergren2723 9 жыл бұрын

Thanks. Very helpful.

@samd410 8 жыл бұрын

Awesome work....thanks

@jimthecarguy 8 жыл бұрын

+Sam Daik Thank you for watching and your feedback

@SteveRobReviews 9 жыл бұрын

Well done Jim

@jimthecarguy 9 жыл бұрын

Thanks for watching and your feed back.Jim

@cancunence35 8 жыл бұрын

Do u have a Video to how to replace the arm control in a dodge caravan 05

@mikeyrozell5627 8 жыл бұрын

ok and can you tell me wat tools I'll need to replace it

@pppppp3883 7 жыл бұрын

what size is the air hose?

@2eagle86 4 жыл бұрын

Those dont need any type of camber alignment when you take off the two bolts off the strut?

@SpicyMcG Жыл бұрын

Wow, If only I had the tools! Thanks!

@jimthecarguy Жыл бұрын

You can do it!

@hb5914 11 ай бұрын

Some of these tools can be rented from local auto parts stores or even hardware stores or other places. When you return the rented tools to some auto parts stores they will refund the rental “cost” so your total expense will be nothing or maybe just the sales tax. Good luck.

@SpicyMcG 11 ай бұрын

@@hb5914 thanks y’all! It’s still not fixed, just chilling… so sad! I’ll have to check into renting parts and gaining the confidence to do it myself!

@knighthawk86855 8 жыл бұрын

how do you remove the Axel if it doesn't have the groove to put the pry bar in, just had the axel replaced in New York. long story but not the seal is leaking trans fluid and I need to replace it asap.... but can't figure out how to get a smooth axel out without damaging the axel, any help would be awesome tks.

@jimthecarguy 8 жыл бұрын

Do you want to call me at work tomorrow?

@turnerholler6902 7 жыл бұрын

what is a flexible plate

@benjolin1623 7 жыл бұрын

Thank you to all you youtubers out there going out of their way to help make it possible for me to fixmy own vehicle.

@jimthecarguy 7 жыл бұрын

I'm happy to help I hope my video was clear and not confusing

@sly5176 7 жыл бұрын

it was great.

@whoispradeep 2 жыл бұрын

Is passenger side also the same process? I was told that passenger side axle shaft is longer and little difficult to replace.

@aorsin 6 жыл бұрын

I was curious about the torque spec on the axle nut. I think you did say that it needs a certain torque but you put on the lock nut before putting the car down and torquing that axle nut to specs.

@hb5914 11 ай бұрын

According to my Haynes repair manual the torque specification for the axle nuts are 180 Foot-pounds.

@trevorkemp9720 5 жыл бұрын

This is my preferred method too - pulling off the strut bolts instead of pulling both the tie rod and lower ball joint. Much easier.

@jimthecarguy 5 жыл бұрын

Thanks for watching. Don't forget to hit the bell for notifications when a new video is posted.

@mikebrodeur12 8 жыл бұрын

Would it be necessary to get an alignment after doing this? Tackling the job on my '05 tomorrow.

@jimthecarguy 8 жыл бұрын

+M Bro Yes it is always a good idea to check the alignment after any front end work.

@eliaschico7781 2 жыл бұрын

changing the right is the same procedure?

@Md-zv6wo 6 жыл бұрын

Would this be the same on a 2007 dodge caravan? There's a video showing different. There are taking ball joints off.

@hb5914 11 ай бұрын

The procedure would be the same on any 2001-2007 Dodge Grand Caravan/Caravan. Short answer; there are two methods. You must choose whether you are going to disconnect the McPherson strut assembly from the steering knuckle or remove the outer tie-rod and/or the ball joint so that the steering knuckle can be rotated enough for the CV axle end to be removed and the replacement to be installed. Which method did you choose?

@GerryJ08 5 жыл бұрын

Hi Jim. I've watched this video at least 3 times so I knew in advance what I was getting into. Note. I had done a previous cv axle replacement on this same vehicle without any issues. This time however, the part of the axle that is inside the transmission just will not pop out no matter what I do. Have you any sage wisdom to share or tools used. I would appreciate any helpful info that you can impart. Please keep the videos rolling. Cheers

@jimthecarguy 5 жыл бұрын

At the 10:20 -10:50 I used a very long pry bar with a slight angle on the end of the bar to get behind the axle and the trans and pop it out. If that don't work place the pry bar on the back of the inner tripod and hit it with a hammer to drive the axe out of the trans. Keep me posted.

@GerryJ08 5 жыл бұрын

@@jimthecarguy Hi Jim. There isn't any room to get a pry bar behind the end of the axle. What are you referring to back of the inner tripod? I am leaning towards a home made slide hammer attached to a vise grip.

@Heather-hy5hi 5 жыл бұрын

Great video. I appreciate the camera stability. Just one thing, kotter pins are cheap. Do not ever reuse them.

@jimthecarguy 5 жыл бұрын

Thanks for watching.

@mikeyrozell5627 8 жыл бұрын

ok and do u have to have a spring compressor for the 2002 model

@jimthecarguy 8 жыл бұрын

+Mikey Rozell No you don't need one

@luilui03able 4 жыл бұрын

what is the price of the axles ? is a very good video easy to understand. thank u for your good job

@hb5914 11 ай бұрын

The price of axle depends on what manufacturer you choose and from what business you choose to purchase them from.

@aaronreyes5787 8 жыл бұрын

Do I need alignment after? Thanks.

@jimthecarguy 8 жыл бұрын

Yes when ever you do any front end work you should check the alignment.

@stevenbuell5387 3 жыл бұрын

Some times not all the time how you get that snap ring off to pull the axe there

@disembodiedlove 8 жыл бұрын

Excellent informative video. If you make many of these, maybe you should get an audio compressor. Then the sound of the air wrench and your voice will be equally loud. Not complaining, just saying.

@jimthecarguy 8 жыл бұрын

+disembodiedlove Thank you for your input.I am in the process of getting new equipment.

@disembodiedlove 8 жыл бұрын

+jimthecarguy Robbie at category5 tech tv describes his system in episode 307 starting at about 57 min. into the show. The video is mostly about virtualizing a physical computer onto a linux system, but you might glean something from Robbie explaining his rig.

@jeffcrouse2836 7 жыл бұрын

wasn't the washer on the other side of the axle nut when you took it off?

@unkulmark 7 жыл бұрын

There are 2 washers used. First the inner thicker washer is put on before the nut. Then the thinner spring-washer is put on to stabilize the locking metal cover so it doesn't bounce around and make a 'jingling' noise. The cotter key/pin is then inserted into the shaft hole. For safety's sake I recommend installing new cotters because the old ones have metal fatigue and are usually rusty. I just replaced the passenger side CV axle on my 2001 Caravan and both cotter pins were in very bad condition. On mine I also had to remove the tie-rod castle-nut which had a worn out cotter.

@johndumas4467 6 жыл бұрын

Since your taking it loose from the struts, what about wheel alinement?

@truthbetold7170 6 жыл бұрын

there is no room for alignment in bolts you should be fine chamber adjustment is usually done from the top side of the strut where it is mounted to the body but most manufacturers only allow one adjustment from the factory you would have to drill out welds to have the ability to adjust the chamber .

@joeydecoursey3759 5 жыл бұрын

It will need an alignment this way taking spindle off strut requires an alignment

@mikeyrozell5627 8 жыл бұрын

is the 2006 Axel change job the same as a 2002 Axel Chang?

@jimthecarguy 8 жыл бұрын

+Mikey Rozell Yes it should be

@davidthurner5126 9 жыл бұрын

is it true that you have to change both sides when one side goes out?

@jimthecarguy 9 жыл бұрын

Hi David Good question.No the only time you need to change both axles is if the boot is broken or possibly starting to crack.

@view385 5 жыл бұрын

You forgot to mention that the wheel alignment had changed since the strut bolts were removed

@glenkahpeepatow2916 4 жыл бұрын

How does one change the passenger side axel

@kansasgardener5844 4 жыл бұрын

It's the same just remember to get an alignment when your done.

@copykon 8 жыл бұрын

Some axle's do not have that groove making it difficult to remove without damaging.

@lookout816 8 жыл бұрын

Thanks!

@jimthecarguy 8 жыл бұрын

+Chris Seymour Hope I was helpful.

@lookout816 8 жыл бұрын

Yes, Excellent video! Thanks for posting

@2eagle86 9 жыл бұрын

How would you change out the seal on that side as well if one were to go bad??

@jimthecarguy 9 жыл бұрын

+twoeagle86 Its very easy once the axle is out.You remove the seal with a puller and install the new with a seal driver.

@2eagle86 9 жыл бұрын

Yeah I was just wondering cause there's like a bolted on flange that our chiltion manual says cant be done by the home mechanic.

@matthewcarder5927 8 жыл бұрын

awesome i can totally do this, thank you.

@jimthecarguy 8 жыл бұрын

Thank you for watching and your input. Keep me posted

@MrCougar214 6 жыл бұрын

Old vid I know. But if that isn't your van, you do know you cost your customer the cost of a unnecessary front end alignment right? All you had to do was drop the lower ball joint and swing the whole wheel and spindle assembly forward. That would have given you plenty of clearance to remove the axle.

@trevorkemp9720 5 жыл бұрын

With the method shown, it should not need a realignment, because he didn't take off the tie rod. At most, the strut bolts could affect camber, but so little it doesn't really matter (stock strut tower bolt holes are non-adjustable), not nearly as important as toe. Also I think it's inaccurate to say that a car like this needs a realignment even IF you took off the tie rod ends - if you don't change the number of turns on the tie rod end (which shouldn't happen if the lock nuts are on anyway), then you can't even change the toe if you wanted to - how is that possible if you didn't change the length of the tie rod and you put it back the way it was before? Alignments are not voodoo magic - the mechanic would need to undo the lock nut and turn the rod end in or out.

@mikekimmerer4647 10 ай бұрын

Right side?

@jayniegalentine9769 7 жыл бұрын

why wouldnt you replace the seal at same time?

@ciastkarzc8287 5 жыл бұрын

Because it is not his van and he does not care. The customer will come back with leaking axle seal and will pay same labour cost to change a $5 seal.

@larrykendel7186 Жыл бұрын

We’ll explained and demonstrate d thanks

@tyanite1 5 жыл бұрын

And my shop would charge 2 grand for this relatively simple operation. Thanks for the DIY video. Did anybody try what MrCougar214 wrote below about simply dropping the lower ball joint to get the axle out?

@stevenbuell5387 3 жыл бұрын

2 GS wtf or they smoking there ??? Shit if folks paid that much I need to work for you sir .

@stevenbuell5387 3 жыл бұрын

What the what's the torque on them bolts if you do it by hand ???

@stevenbuell5387 3 жыл бұрын

Can you just take the tie rod off there to turn it off there ??/am replacing my tie rods anyways