HOW TO Reshape A Carbon Motor Brush / Brushes Bedding

Рет қаралды 25,058

2 жыл бұрын

Today we show you a way to bed / reshape carbon motor brushes, in my case, because one of the brushes broke off (and I don't want to buy new ones). Bedding ensure that the contact faces of the motor brush matches the curve of the commutator (or slip ring) as, exactly as possible, so that no electrical overload of individual brush parts occurs. The method of bedding brushes is to put a long strip of abrasive cloth under the brushes, the abrasive cloth being then drawn backwards and forwards (for bi-directional machine), or in one direction only (direction of rotation for uni-directional machine). While bedding can be done for big motors with the brushes and commutator in place, sometimes, it is not possible to do so due to the construction of the machine (like here for this drill where the plastic housing stands in the way). I'm therefore building here a little jig that will allow me to do the brush reshaping externally, to still ensure that the motor brush is perfectly bedded.
► YOU WILL NEED
- Abrasive cloth
- Rod with the same diameter than the commutator
- Screws
- Piece of wood
► DISCLAIMER
Always make sure you operate in a safe and secure manner.
For this project, take your time, work slowly and check progress.
Grinding brushes can be messy so clean as needed.
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
► SUBSCRIBE (weekly content)! bit.ly/SubscribeTheLabOtomy
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
► CATCHUP! All Videos bit.ly/AllTheLabOtomy
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
▼ CONNECT!
► Facebook: bit.ly/CauseIHaveNoFriends
► Twitter: bit.ly/LikeASheep
► Instagram: bit.ly/NarcissisticByNature
► Tumblr: bit.ly/AnotherCatGif
► Pinterest: bit.ly/SniffDaMoodBoard
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
▼ MUSIC
► "Fidget Waltz on my finger" by the LabOtomy
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
╔══╦╗╔╦═╦╗╔═╦╗╔═╦══╦═╦╗╔╦╗╔╗
╚╗╔╣╚╝║═╣║║═║╚╣║╠╗╔╣║║╚╝╠╗╔╝
═║║║╔╗║═╣╚╣╦║║║║║║║║║║╠╣║║║═
═╚╝╚╝╚╩═╩═╩╩╩═╩═╝╚╝╚═╩╝╚╝╚╝═

Пікірлер: 17

@powerofknowledge7771 2 жыл бұрын

This was a very well put together video! It deserves way more views! Thank you for sharing this info!

@TheLabOtomy 2 жыл бұрын

Thanks for the feedback Angela, happy you liked it

@israelhernandez9911 11 ай бұрын

Mucho pedo

@markwilliams2830 2 жыл бұрын

Thanks for sharing this excellent tip.

@TheLabOtomy 2 жыл бұрын

Glad it was helpful!

@gromozekabes1581 22 сағат бұрын

Для чего нужны эти щетки?)

@spartan187 2 ай бұрын

I prefer to do with file and fine tune with sand paper later , don’t need so much mess

@shawncrittenden6216 3 ай бұрын

Nice if you had removable holders, guess I'm milling myself a slot in a peice of scrap and making my own.

@TheLabOtomy 3 ай бұрын

Nice!

@BobbyBrady-iz2mc 9 ай бұрын

Okay so what if I put the drill armature in the dril and hold or fasten the brush as you did and spin it on the carbon?

@TheLabOtomy 9 ай бұрын

If you get the space to do so, also works

@osmanpasha_diy 2 жыл бұрын

How did it end up this angled in the first place?

@TheLabOtomy 2 жыл бұрын

Good question! This repair is part of a longer restoration project where I repaired a hammer drill found in a crate: kzfaq.info/get/bejne/j7J5mrOQq7rFm2Q.html I have no background around what happened with the drill, so can only speculate at this stage. My 2 theories are (seen the state of the drill): 1) the drill fell breaking the carbon brush, 2) the carbon brush broke due to arcing

@RimjobHimself 6 ай бұрын

Ehy didnt you just brysh it against sandpaper without that setup?

@TheLabOtomy 6 ай бұрын

To give them the proper bedding (which in this configuration could not be done with the brush in place)

@RimjobHimself 6 ай бұрын

@@TheLabOtomy ok, I didn't think about that they surely could break if you were to careless. Thank you anyway. :) Just seemed a lot of work, but I do things like this my self all the time. A 2 minute job can easily be overthinked into 8 hours at my place. Haha

@TheLabOtomy 6 ай бұрын

@@RimjobHimself Yep, same here