Hello Darren. I think you don't understand fine the method for use it. The two antennas needed the same gain at time and after modify the phase. For this, decrease the gain of main antenna (usually have more gain than rx antennas used) and decrease a bit the rx antenna. You first need to find the point where all the noises (or the better s/n ratio) you have. At this point, the two antennas have the same gain. Then you can move the phase Potenciometer to kill the noise. You can see it in a video of my channel.

Thanks Capt

Good video thanks

Friend, what do you do if you don’t have a push to talk or a PTT on the back of your radio, I have a Quad five any tone it doesn’t have a PT T Jack

nice, awesome

were on the FTDX10 would you connect the PTT connector?

Cool...Have power line everwe're around my house...👍like it...Thanks

Impressive, but maybe you can explain something for me. The QRM was bad, but the QSO signal was still stronger, pusing the S-meter to 9. When you turned on the QRM Eliminator, the QRM went away, but the S-meter dropped to about S-2 on that strong signal. What caused the dramatic drop on the S-meter without any audible loss in signal strength?

Is the transmit power that handles 100 W continuous or 100 wpep??

Hi I have the FTDX1200 and it has a PTT jack on the back and not a TX Ground, Can I use the PTT Input?

Turning the IPO amp1 off help also? Thanks for the video I have the FTDx10 but considering the 101mp great Rig thanks

How does it compare with the qrm eliminator by us4lg igor?

I was thinking about getting one👍

I agree that a shorter sense antenna would be desirable so it only picks up the local noise and use vertical polarization on the sense antenna.

8:00-9:00 mins, your received signal was reduced with the ambient level, signal%noise was unaffected, it's just an attenuator 💃🏼

You should set the gain 1 to as near as max as you can otherwise it’s just an attenuator.

I have a radio without ptt connection . Can i use this device not connecting the ptt-cable?

You should be using a MUCH shorter aux antenna. You will not get the full effect of that device when the auxiliary antenna is also receiving The wanted signal. The antenna should be a 3 ft piece of wire or shorter so that it only picks up The unwanted local noise and not the signal of the other transmissions you want to hear

How can I use this using a pw1 amplifier I've got four antennas completely filled on the back of the pw1 how would I rig this up to work with the pw1 and the Icom 7700? Thanks Mark

Diversity tuning is brilliant, benefits of a dual VFO transceiver to do this in the radio itself. Tried this on the SDRplay Duo.

whereabouts would i attach the ptt connection on the yaesu FTDX10?

Hello Darren N4VFR I hope you are feeling good I have a lot of line noise here lately yesterday it was 20 over 9 on HF what is weird it comes and goes if it's raining no noise the noise blinker is useless on this radio Yaesu FTDX101 MP the Icom IC 7610 Scott a lot better noise blinker ON it it will take out over 80% of the noise my icom ic 9700 it is got the best noise blinker on any radio I've ever owned on 2 meter SSB it will get rid of static crashes I was wanting to ask you about The QRM Eliminator I believe it will only handle 100 Watts I'm not for sure but you turned the The qrm Eliminator off can you run 200 Watts thank you Darren N4VFR 73

I have a different problem, I have a noise floor of s3-4 normally, but I get a broadband burst every 15 seconds with a 12-13 second duration. Totally overwhelms the receiver. I don't think that it can be phased out. Still, for ambient noise with a consistent noise level, it seems to be the ticket. Thanks for the video. 73, Al

I just bought it last week and still trying figuring out its pattern. Now my auxiliary antenna has some distance to my main antenna, cancelling the noise is a little tricky; I need to cancel out different noises for different phases. Sometimes when two noises came in with different phases, there is a trade off. I've discovered that putting Gain 2 at level 5 (middle), it can do the job most of the time by only adjusting phase knob. However, when auxiliary antenna cannot reap enough noise, Gain 2 need to be at level 10 (highest) while Gain 1 should reduced to some extent. All in all, when spare time comes, I'll try for put both of the antennas close to see the result. Literally, I guess using beam antenna as the main should benefit a lot from this toy.

Why didn’t you get the one from MFJ?

Must the PTT be connected, as my radio doesn't have a TX ground?

Where did you buy yours? I have a MFJ1026 that works well but want to try this unit. Thanx for the vid.

hi darren how long is your aux ? thank you

Thank you for the interesting video . I bought one yesterday. I use a yaesu ftdx 3000 . And also a acom 1010 amp . But the acom use also the tx ground connector. Do you have any idea that i could connect the xphase to a other connector in the yaesu ? Or using a rca splitter on the tx ground ? No idea of this could do any harm ? I dont want to destroy the apm 🙂 .... And the xphase dont work if you not connect the ptt ?

This is only effective if there is truly a local noise. Local noise as in a property noise that can be locally targeted with the position of the aux antenna.

👍👍👍😃😃😃

Where you connect ppt of you have a Galaxy Saturn?? Thanks.

Ok the reason this is not working is because your rx antenna needs to receive the noise the same or louder than your HF antenna. If not, your rx antenna is not good enough. If you rx antenna can't get the qrn louder the your HF antenna, how do you expect to cancel the qrn. All you are doing is reducing the gain of the antennas, plus you can't test it while listening to a station! I have the mfj1026 and my rx antenna picks up everything.

I see at 08:30 that the noise drops, but also a LOT of signal drop down! :(

how is the wiring for ptt Xiegu G90?

I never see how you need to wire it up on a normal CB 27 MHz radio

It appeared to reduce both the qrm and the station you were trying to hear 🤔

i told you them earth rods would give you noise didn,t i lol only joking there cpt lol no great stream mate and can,t wait to get you in my log mate but thats if you can hear me over the noise lol eee. 73 mate and enjoy are wonderful hobbie from M7BYF in liverpool england

Hello Captain Darren I got a Yaesu FTDX 101 MP QRM Eliminator is turned off can you transmit 200 watts ON it another problem I would have with The qrm Eliminator all my HF antennas come in the House to a big 2K a Ten Tec 229B manual Antenna tuner on the back of my Big Ten Tec 229B antenna tuner I got a coax jumper running to antenna switch box for two different Radios Yaesu FTDX 101 MP ICOM IC 7610 thank you 73

I got one but don’t use any more I found better to choke noise out

From 8.00 min it clearly takes out some of that 'raspy' noise.

I got the same thing on my radio. It's called rfgain. I say this because ,you're killing the wanted signal along with the noise. Note s levels. Snake oil

👏👏👏👏👏👏👏 PU5WCZ👍👊🙏

why would you use your pre amp?.... first way to cut your noise is to attenuate your signal not amplify it.... just sayin

You turned down your main antenna most of the way.

Hello, I have this device, unfortunately without instructions. Am CB radio operator. Can you please tell me what I have to connect where and how I set up the device. Best of all, step by step. I thank you in advance. With kind regards 

Common mistakes that people do and they THINK they reduce noise. See this part of the video kzfaq.info/get/bejne/lcWSqdKG0Z2laIk.html Here you think the noise is down, but you are actually attenuate BOTH the signal and the noise. The signal is already S9+ and when you switch on the eliminator, the signal drops to S2. However the noise also drops to very low levels. You think that you have the correct setting, but in fact all you did is attenuate the signal and the noise! If you try to recover a weak signal with this method, you can never do it! I do not say the x-phaser does not work at all, It is just not the correct setting in this part of the video.

Easier to move house.

Thanx Cap'n D :-) I love the ham energy you have and I expect you deliver that focus and energy to be tuned in as necessary as a pilot. AS mention previously, I am in Mims FL (between Daytona and Melbourne - near Titusville) - wish I was closer I would want to visit you. Thanx for the clip re: QRM Eliminator - tho puzzling to me is I thought your noise problem from a few months ago which was truly awful, was cleaned up by the power company ? is this a different unidentified source? cheersw - and again love your video clips - well done and your entire setup challenges and directions you took were informative. Cheers 'n 73 Cal K4BEW (see my profile on QRZ.com)

now I understand how to use qrm eliminator. tnx.