How-To: Shingle around a vent pipe Flashing

No video

How-To: Shingle around a vent pipe Flashing

Рет қаралды 145,805

8 жыл бұрын

If you want to help support Shannon to produce more videos like this, visit www.house-impr...
Shannon from www.house-impr... shows you how to shingle around flashing on your roof.
If you have questions about your home improvement projects, stop by the forum on our website, where Shannon will answer your questions in detail for free.
Website: www.house-impr...
Facebook: / 180657245288627
Twitter: / house_improve
Here is a link to all of our shingling videos: • Roof shingling
Video © 2016 SKS Media. Videos produced by SKS Media (House-Improvements.com) are provided for informational purposes only. The information contained in the videos is intended to give general guidance to simplify DIY (do it yourself) projects. Because tools, products, materials, equipment, techniques, building codes and local regulations are constantly changing, SKS Media cannot and does not assume any responsibility or liability for the accuracy of the information contained therein. Further, SKS Media will not accept any claim for liability related to, but not limited to, omissions, errors, injury, damage or the outcome of any project. It is the responsibility of the viewer to ensure compliance with all applicable laws, rules, codes and regulations for a project. The viewer must always take proper safety precautions and exercise caution when taking on any project. If there are any questions or doubt in regards to the element of a project, please consult with a licensed professional. SKS Media conducts all matters in accordance with the laws of Saskatchewan, Canada.

Пікірлер: 87

@DuStY_rZz653 3 жыл бұрын

U nailed right on a seam

@hding98 5 жыл бұрын

Helpful video. Good suggestions from viewers make it better. Thanks to all.

@angelobarone9448 4 жыл бұрын

Thank you for all your videos! You help me every time I need it just like this one for the roof vent. Keep up the good work

@HouseImprovements 4 жыл бұрын

Glad to help!

@awsomeching2002 7 жыл бұрын

thank you! your shingle videos are helping my husband and i out alot while we do out own roof👍👍

@gabeg4427 4 жыл бұрын

He is not a roofer

@tchogworks1987 2 жыл бұрын

Won’t the cement seal the bottom edge? Do you really need those exposed nails

@spectrepro 2 ай бұрын

Wind

@Anonymous-rm6fi 7 жыл бұрын

Good video, the only thing I disagreed with was putting the 3 nails at the bottom of the vent boot, I would have nailed just the top and out roofing cement on the bottom.

@siscokid2492 7 жыл бұрын

Same I wouldn't have nailed it on he bottom.. Two on each side near the edge on top and another befor the next shingle starts. That way it doesn't show.

@DASamX5453 4 жыл бұрын

Over time if you do that, even with a Perma Boot, the plastic bends up leaving the underside exposed...I have it happening on my roof right now and all cause I didn't nail the bottom down and just roof cemented at the bottom thinking it was better...better to nail and then dab the nails...

@thomascervantes6258 8 жыл бұрын

Another good video Shannon. Man The only thing that worries me is those pipe boots, turtle vents and Stacks not Dryed In. Say a big Strom comes and rips those 20yr. Shingles off and water get to running. I've always used a full Shingle and centered it on the top cut so u don't have any stagger pieces so close to the top of the pipe boot that's just me. God bless and Keep up the good work .

@HouseImprovements 8 жыл бұрын

Thanks Thomas

@wicken486 Жыл бұрын

glad I watched this video, been many years since I helped my dad do roofs, closing in on 40y.o and had to get a roof replaced on my house, contractor's rep couldn't explain to me why they needed to leave some shingles near the pipe and flashing not completely sealed and *contractor was of course busy with other jobs at that time, kindly pissed me off however, now it makes sense watching your video, thank you from bottom of my heart.🫂

@KhalidAli-lb2lc Жыл бұрын

Thank you

@vipahman 3 жыл бұрын

The vent flashing is nothing but a shingle. If you get that, you know what to do.

@DoneRightReviews 2 жыл бұрын

Hi Shannon... I LOVE your channel. What are your thoughts regarding NOT running a bead along the bottom underside of the flashing? I've always leave a small gap so any water or condensation that MIGHT form has a place to escape.

@HouseImprovements 2 жыл бұрын

That would be fine.

@z1522 4 жыл бұрын

At 3:00, you DON'T need to put nails exposed, below where a shingle would cover. If you can't get the flashing to lay flat enough to suit you, stick adhesive under the corners, but the entire principle of layering so water cannot find an entry weakness has been compromised the minute you just start driving unsealed nails all the way from the exterior to the inside of the roof; sealing the head does not seal the underlayers.

@e.duanehortman4944 4 жыл бұрын

Yes you do. You are so wrong

@logowatchman 7 жыл бұрын

Well done. Clear explanation and demo. Thanks.

@jonathanfowler208 11 ай бұрын

Thanks for the clear easy simple explanation and tips.

@BicBones 2 жыл бұрын

very informative! thank you for your video.

@davejohn255 4 жыл бұрын

Thank you.

@magnificentone16 5 жыл бұрын

No issues with how he's installing the flashing, just worried about how hard the nails are puncturing through his shingle, and how close each nail is to the key line?

@e.duanehortman4944 4 жыл бұрын

This is a very thorough video, however it is terribly wrong lol

@brendamiller-dv6kt Жыл бұрын

Excellent...my job for tomorrow!

@Carlostype 8 жыл бұрын

Nailing so close to the lower shingle edge worries me a little even though there's a little strip of tar running across but enjoyed this series all the same!

@HouseImprovements 8 жыл бұрын

Thanks for watching

@DNGJustSnakes 3 жыл бұрын

So glad you are not EVER shingling one of my houses....so much room for improvement!!!!!

@Mechanix04 3 жыл бұрын

I've seen it done this way a hundred times and it was dry as a bone. I don't know what ur fucking problem is other than being a know fuck all douche....

@Mechanix04 3 жыл бұрын

Username checks out lol

@screaminpotato 8 жыл бұрын

Same instructions apply for a roof vent?

@HouseImprovements 8 жыл бұрын

Keep watching, that video will release Sunday May 29/16

@Mdjagg 6 жыл бұрын

You don't want to do your tar line like that, and it should be the exact opposite. The U shape should cover the left, top, and right side, with the bottom open so that water can escape.

@jamesp2391 6 жыл бұрын

The tar line should go all the way around the pipe. I have seen where wind driven rain was blown in under the bottom edge of the flashing when installed like you say. I have also seen where hornets will get under the flashing on the bottom edge as well. After hurricane Katrina I was called to a house that had major damage to the living room with no damage to the roof at all. The roofer had installed a vent just as you have said and it was the cause of the internal damage to the house. The ARMA (Asphalt Roofing Manufacturing Association) manual on page 55 just says embedded in a bed of roof cement. It does not say just on three sides like you say.

@bakecorn 5 жыл бұрын

Right

@johnlieb1 5 жыл бұрын

Ma Ja u r correct but I always apply dabs of tar at the bottom. Because there should never be nails exposed at the bottom. Also I wrap pipe with I&W shield before paper and shingles

@johnlieb1 5 жыл бұрын

and he needs to turn the pressure down on the un. Those nails are over driven

@DASamX5453 4 жыл бұрын

@@johnlieb1 Over time if you do that, even with a Perma Boot, the plastic bends up leaving the underside exposed...I have it happening on my roof right now and all cause I didn't nail the bottom down and just roof cemented at the bottom thinking it was better...better to nail and then dab the nails...

@AnonYmous-qg4ph 6 жыл бұрын

Both those shingles should have been cut around the flashing. You effectively shortened your stagger to 1" in a critical part of the roof (penetration).

@Mechanix04 3 жыл бұрын

I just did my roof that's almost 30yrs old and it was done the same way as this video. No damage and everything was ok. Please don't post misleading information

@DoneRightReviews 2 жыл бұрын

@@Mechanix04 Respectfully... there are plenty of things done improperly that don't fail. I'm glad you've been ok, but the response above is NOT misinformation; he is correct. This is a terrific channel, btw. :)

@mr.d4295 6 жыл бұрын

A perfect video of what not to do.

@MoneyManHolmes 3 жыл бұрын

Still did better than 90% of roofers out there in the real world.

@Bluecollar711 5 жыл бұрын

Very good presentation but the second-to-last should be fully cut chamfered around boot

@beebob1279 2 жыл бұрын

My roof is nearly thirty years old. Recently we’re having leaked in our kitchen. I’m thinking it’s coming from the vents, because it looks like the guy who roofed the house before I bought it didn’t leave the flashing on the bottom like you’re doing. It’s so frustrating because I even know todo that and I’m not a roofer.

@reedcarpenter2994 3 жыл бұрын

We just had a roof installed and the bottom flange is not visable. Why would this be? It appears they shingled all around it flush.

@darchangel4295 3 жыл бұрын

That method basically directed water under the next lower shingle, not a good thing. You want the water to shed over the next row of shingles.

@billhamilton7524 5 жыл бұрын

many of these flashing say use no tar ,,why is that ?

@mr.d4295 3 жыл бұрын

Because this guy has no clue what he is doing

@Kiowagoodfella 8 жыл бұрын

I was curious, have you worked with metal roofing much and if so is it harder to work with than asphalt shingles. I would really like to see you do a metal roof installation video someday. Thank you for your very informative videos.

@HouseImprovements 8 жыл бұрын

You have not seen our famous shed building series? We do a metal roof on that shed,it is small scale but should give you a bit of an idea. kzfaq.info/sun/PLh0KqGKtX4oU9z9ok2mtVO6cacPD_Mbw4

@Kiowagoodfella 8 жыл бұрын

Thank you sir, I'll check it out.

@MrFelix617 7 жыл бұрын

thank you Sir great job !! subscribed

@klaatu2 4 жыл бұрын

Don't listen to this guy. That Ushaped bead is a disaster. Trapping the water

@sikkinixxmc 8 жыл бұрын

Thank You great videos as always

@HouseImprovements 8 жыл бұрын

Thank you

@jtyw1 2 жыл бұрын

Nice olfa bud.

@jtyw1 2 жыл бұрын

Yer fired.

@hollyblumenberg6685 5 жыл бұрын

Wish you were close to me, I need a repair somewhere near a 10 inch diameter, range hood roof vent 😟

@dennisbland6559 5 жыл бұрын

Rubberized on exposd nail not roof cement. Cement goes where it's not exposd to the ⛅.

@billhamilton7524 5 жыл бұрын

U R RIGHT ,,tar does not hold up ,,amazing how many people use it,,its GARBAGE ,,Sika const sealant is the best

@terrancegrant1664 8 жыл бұрын

Great videos..thanks!

@HouseImprovements 8 жыл бұрын

Your welcome

@daxx2433 8 жыл бұрын

nice video. greetings from god old germany.

@HouseImprovements 8 жыл бұрын

Thanks for watching

@Okidiver0907 4 жыл бұрын

If this was new construction, why wouldn't you nail the vent down to the sheeting (plywood) then cover the flange with your tar paper and shingle over all that?

@gabeg4427 4 жыл бұрын

This is all wrong... remember, water runs down and into cracks.... you shouldve installed the flashing/collar while while doing the shingles. So you can have a no caulk and good looking roof.

@thaynezimmerman7786 4 жыл бұрын

100% a leak. The shingle you cut in has a 2” step.

@MrPatdeeee 4 жыл бұрын

On my roof, they caulked over the nails, that they put in the bottom of the flashings. In ALL 3 cases, the caulk cracked and ruined my ceiling in 3 rooms. MOST honest, true professional roofers do NOT put ANY nails in the exposed part of the pipe flashing. And the reason is what I am experiencing. For the same reason you don't nail ANY exposed part of the shingles. If you are concerned about the bottom of the flashing raising up, it is best to put sealing UNDERNEATH the bottom of the pipe flashing. ONLY nail the flashing at the top and side of the flashing. NEVER through the exposed bottom. Caulk over the nails is NOT the answer; for in MOST cases the caulk will crack in a few years. When that happens, water will go down around the shank of the nail and that allows leaks in the ceilings of the home. Best MOTTO: " I will NEVER nail into the bottom of the exposed flashing. AMEN!"

@foxwood67 5 жыл бұрын

I would never use a plastic flashing with EPDM collar. That'll last 10 years max. Also never leave the nails exposed just nail the flashing under the shingle where it overlaps the flashing . Finally if thats a new roof why didn't the 8" heater flashing get replaced behind you