HOW TO SOLVE - Artillery Sidewinder X1 CheckSum Error

Рет қаралды 6,321

4 жыл бұрын

Printer:
🔴 Artillery 3D Printer
✅Aliexpress - s.click.aliexpress.com/e/_9RHm0f
Do you want a better adhesion in your bed?
Kapton tape - www.banggood.com/custlink/DvK...
Check this video
• High Temperature Kapto...
🎧Music
MU - Free music for your videos channel - bit.ly/2GdDmB9
✩Facebook Official Page
/ flyerfpv
✩Instructables
www.instructables.com/member/...
✩Blog
flyerfpv.blogspot.pt
✩Instagram
/ flyer.fpv
#Artillery #3DPrinter #CheckSum

Пікірлер: 36

@LanceLegaspi 4 жыл бұрын

It's always advantage to have that knowledge. Thank you for sharing the formula.

@MCsCreations 4 жыл бұрын

Great tips, dude! 😊

@NunoFlyer 4 жыл бұрын

Thanks dude.

@chasharper 4 жыл бұрын

Very nice job showing how to fix that error. Big like 11 hope you have a Wonderful week . 👍😎

@ATJHTRAVELS 4 жыл бұрын

Great video and tutorial sledgehammered that like button shared this out and a enjoyed watch

@NunoFlyer 4 жыл бұрын

Thank you friend.

@Ali-kg7sh 4 жыл бұрын

Nice video 👌🏼

4 жыл бұрын

Mais um bom tutorial. Tem um um ótimo dia, caro amigo.

@NunoFlyer 4 жыл бұрын

Muito obrigado!

@CanaldaMariadoCarmo 4 жыл бұрын

Interessante vídeo

@Dave_the_Dave 5 жыл бұрын

When you are adding print speed, you can add more than 1% at a time. Hit the grey button that says 1% and it should change to either 10% or 5%.

@TheBuenoWorldDrone 4 жыл бұрын

Nice video. Thanks for sharing. Like#15. ^-^

@oliverbechmann1628 4 жыл бұрын

Hello, I have also problems with to much heat on the extruder motors. I check the Voltage on all Drivers is between 0,98-1,01 Volt. You are sure that 0,5 Volt is enough for fast movements? I think I try 0,75 Volt on all Drivers.

@NunoFlyer 4 жыл бұрын

already tested with 0.5V on all drivers, looks good anyway I recommend 0.7V, Im using 0.7 now without any issue.

@gabrielalej 4 жыл бұрын

I use 0.8

@starblazer13 4 жыл бұрын

So what is the action item to fix it? How do you adjust the vref?

@NunoFlyer 4 жыл бұрын

To avoid the checksum error, printer stop by overheat. You can adjust the vref like you can check in this minute 1 11 kzfaq.info/get/bejne/d7x-nbOXla6vmIE.html Just turn left or right the potentiometer.

@Gretoragol 4 жыл бұрын

It worked for me! I was getting weird checksum errors when printing from the sd card (while with the USB stick it was skipping gcode... heven't verified yet that it fixes the USB stick as well, printing from the SD now). Originally my voltages were set to 1.008 for almost all drivers before (+/- 0.030V). I've set all of them to 0.7V. This is my first day I got the printer and I already voided my warranty by doing this :) Unbelievable that I had to do a fix that appear to be required... I am more confident that it is required because someone said with v1.5 it was 0.4V out of the box (I believe I got V4 here in Canada, not sure where you can confirm the hardware version)

@Gretoragol 4 жыл бұрын

So the problem with the USB memory stick skipping gcode is still there, so I guess a different problem... anyway for now I am going to use the sd card, as long as it is stable I'm happy. I did a test multiple times, and in the last one I copied the gcode file that was skipping a part of the initial layer (a simple XYZ test cube) from there USB stick to the sd card and it printed fine without skipping on the sd. I also tested with 2 different USB stick and I have the same exact behavior & problem.

@NunoFlyer 4 жыл бұрын

Hello, Yhea, I recommend 0.7v, what I have printing a lot of time without problems. You can check the version that you have through this image that I did for you. ibb.co/PtzqkZF

@NunoFlyer 4 жыл бұрын

Honestly I never tested the SD card :) Im using USB stick without problems, strange, I never see anyone with that problem.

@bestkoreanjesus 3 жыл бұрын

where did you change the voltage?

@NunoFlyer 3 жыл бұрын

Vref pot on drives ;) 1:06 red probe point

@moldesmatrimaki 4 жыл бұрын

La cama y el extrusor estan en 0/0 0/0 y no funciona . Sabes que hacer?????

@NunoFlyer 4 жыл бұрын

Mira los parametros no teu slicer, puedes tener um erro.

@kokitofpv2953 5 жыл бұрын

por favor ¿cual es el script de inicio?

@NunoFlyer 5 жыл бұрын

G28 M117 G92 E0 G1 Z1.0 F3000 G1 X2 Y20 Z0.3 F5000.0G1 X2 Y200.0 Z0.3 F1500.0 E15G1 X2 Y200.0 Z0.3 F5000.0G1 X2 Y20 Z0.3 F1500.0 E30G92 E0G1 Z1.0 F3000 M117

@AndreW-ci3ub 4 жыл бұрын

Have the same mistake with the checksum and he stops during the printing and continues at some point. I put down the voltage from 0.94v to 0.75v, but both errors remain.

@NunoFlyer 4 жыл бұрын

So, try change the tft screen cable, white 4 wires connector.

@qui3scent 4 жыл бұрын

@@NunoFlyer Do you know where to buy this screen cable?

@NunoFlyer 4 жыл бұрын

@@qui3scent Artillery company sent me one.

@qui3scent 4 жыл бұрын

@@NunoFlyer Thank you! I actually just returned the whole printer to Amazon for a new one.