How To Stop Car Underbody Rust - Step By Step Guide Using Bilt Hamber Hydrate And Lanoguard (£5 OFF)
Рет қаралды 12,020
Күн бұрын#car #diy #rust #everythinghome #mitsubishi
How to stop rust and reduce the risk of future corrosion problems with Bilt Hamer Hydrate 80 and Lanoguard.
🛒 Everything you’ll need for the job #:ad
⭐ Products:
🎁 *Get £5 off your order with the link below* Lanoguard Underbody Protection Kits
snwbl.io/lanoguard/SHANAKA17034
Milenco Wedges Set of 2 Ramps
UK: amzn.to/3XLuzMn (Amazon)
US: amzn.to/3D075JT (Amazon)
Wheel Chocks
UK: amzn.to/3NI6a5X (Amazon)
US: amzn.to/46yDc0S (Amazon)
Bilt Hamber Hydrate 80 Rust Killer
UK: amzn.to/3CXdfdQ (Amazon)
US: amzn.to/3DjBuTP (Amazon)
Degreaser
UK: amzn.to/3PKoIF9 (Amazon)
US: amzn.to/3rhbmGl (Amazon)
Filter Mask:
UK: amzn.to/3rk2Tls (Amazon)
US: amzn.to/44rH56t (Amazon)
Protective Sheet
UK: amzn.to/3XCM2GK (Amazon)
US: amzn.to/3XCQe9k (Amazon)
🛠 Tools:
Roughneck Heavy Duty Wire Brush With Scraper
UK: amzn.to/3reXhcp (Amazon)
US: amzn.to/43hm0Km (Amazon)
Engine Shield Trim Clips:
UK: amzn.to/3reD86c (Amazon)
US: amzn.to/43f4y9c (Amazon)
Engine Shield Bolts:
UK: amzn.to/3D3LFeZ (Amazon)
US: amzn.to/4386hNP (Amazon)
Trim Removal Tools
UK: amzn.to/3rhFhOD (Amazon)
US: amzn.to/3NG5VrT (Amazon)
Please note this is NOT a sponsored video.
Timestamps:
00:00 - Intro
00:38 - Preparation removing existing rust
03:25 - Applying the hydrate 80
04:28 - Hydrate 80 in action
05:48 - Lanoguard
08:20 - Before and after
09:15 - Final thoughts
Found this video helpful? You can now buy us a coffee ☕ www.buymeacoffee.com/Everythi...
If you’re looking for more great advice related to Everything Home, make sure you subscribe to our channel.
*FOR MORE EVERYTHING HOME*
- Join our FACEBOOK GROUP - groups/14175...
Or check out these videos too:
Mitsubishi Outlander PHEV Remote Control App Setup [2020] - Android/iOS - Charge | Climate | Status
• Mitsubishi Outlander P...
How To Secure An Electric Car Charging Cable - 5 SIMPLE Solutions [2021]
• How To Secure An Elect...
How To Defrost A Car Windscreen Without Leaving Your Home - Mitsubishi Outlander PHEV App #Shorts
• Mitsubishi Outlander P...
RENEWABLE ENERGY
Octopus Energy Smart Meter NOT Required! Tracker Tariff Review [2020] - Rates Comparison & Sign Up
• Octopus Energy Tracker...
RENEWABLE ENERGY
Octopus Energy: Agile Tariff [2020] Get Paid To Use Electricity! How It Works And How To Sign Up
• Octopus Energy: Agile ...
*VIDEO EQUIPMENT, SOFTWARE, VIDEO and AUDIO*
AKASO EK7000 4K Sport Action Camera Ultra HD Camcorder 12MP
TONOR USB Condenser Microphone Kit, TC-1020 Cardioid PC Mic for Gaming, Recording, Studio, KZfaq, Voice Over, Podcasting, Streaming, Chatting, Mac, Windows, Laptop
VILTROX L116T 5600K/3300K Bi-color LED Light Panel Dimmable Video Light Kit
Canva Design Creater. Try it for FREE now
www.canva.com/join/quail-univ...
KZfaq Audio Library
Nine Lives - Unicorn Heads
Dan Henig - Chimez
DISCLOSURE: We often review or link to products & services we regularly use and think you might find helpful. Wherever possible we use referral links, which means if you click one of the links in this video or description and make a purchase we may receive a small commission or other compensation which allows us to keep bringing you this content for FREE.
@everythinghome Ай бұрын
🎁 **Get £5 off your order with the link below** Lanoguard Underbody Protection Kits snwbl.io/lanoguard/SHANAKA17034
@Lanoguard Жыл бұрын
Hi, thanks for creating a video showing your Lanoguard treatment & showing the before and after clips, they are great, we really appreciate it 🙂
@everythinghome Жыл бұрын
That's no problem at all. It's a great product, works and is easy to use! 👏🏽 Thanks for taking the time to watch and comment on this video 👍🏽
@kevinwillis3390 Ай бұрын
great explanation of the process, going to give my old banger a treat this year to see if i can get another 20 years out of it.😄😄😉😉👍👍 regards Kev
@everythinghome Ай бұрын
Hi Kev - Thanks for taking the time to watch and comment on this video. Glad you found it useful. That's great - you won't regret it. I'm in the process of doing a 1 year review video so if you’ve not already, please do like this video and stay tuned for some more content 🙂
@kevinwillis3390 Ай бұрын
@@everythinghome great be good to see the review already sub'd bell'd and liked👍👍thanks again
@everythinghome Ай бұрын
@@kevinwillis3390 Thanks! Don't forget you can get £5 off your order with the link below snwbl.io/lanoguard/SHANAKA17034
@Scottadamsfan3481 3 ай бұрын
Thanks I was looking for someone to show this process correctly
@everythinghome 3 ай бұрын
Hi Johnny - Thanks for taking the time to watch and comment on this video. Glad you found it useful. If you’ve not already, please do like this video, stay tuned for some more content and thanks for taking the time to contribute to the discussion on this video 🙂
@Luminous_Beings_are_we 4 ай бұрын
Awesome video thank you very much. 🔥🔥🔥🔥🔥
@everythinghome 4 ай бұрын
Hi - Thanks for taking the time to watch and comment on this video. Glad you found it useful. If you’ve not already, please do like this video and stay tuned for some more content 🙂
@john-pauljones878 5 ай бұрын
A really great video, I used this product too to great effect on my rusty landcruiser
@everythinghome 5 ай бұрын
Hi John - Thanks for taking the time to watch and comment on this video. Glad you found it useful. Yea it's great, will be doing a 1 year review and top up coat this summer 👍 If you’ve not already, please do like this video, stay tuned for some more content and thanks for taking the time to contribute to the discussion on this video 🙂
@mjojrjr6231 11 ай бұрын
Please, make a longterm review maybe next year to see how it goes after the winter.
@everythinghome 11 ай бұрын
Hi - Thanks for taking the time to watch and comment on this video. Yes, that's my plan 👍🏽 If you’ve not already, please do like this video, stay tuned for some more content and thanks for taking the time to contribute to the discussion on this video 🙂
@nathangreenwood5990 5 ай бұрын
Iv had it on 2 years on my BMW and it doesn’t look any different to the day I put it on, fantastic stuff!!
@mjojrjr6231 5 ай бұрын
@@nathangreenwood5990 that's good to know, I've done mine last summer. Will have a good check this coming summer.
@nathangreenwood5990 5 ай бұрын
Sorry, I used dynax UC by BH not the stuff the gentleman proceeded to use, I have no experience with lanoguard but the bilt Hamber stuff is still on and working wonders after 2 years.
@mjojrjr6231 5 ай бұрын
@@nathangreenwood5990 I see, I used that Bilt Hamber before applying the Lanogaurd.
@fanfeck2844 10 ай бұрын
Great video, but your lower control arm wasn’t replaced because it was rusty, it’s because the rubber bushes deteriorate, and they replace the whole arm, rather than trying to press out the old ones, and press in new. This process might help keep the bushes hydrated and protected from elements that affect rubber? I plan to do this on a newer car, so should be a little easier
@everythinghome 10 ай бұрын
Hi - Thanks for taking the time to watch and comment on this video. Ah right, thank you for the info. Yes, definitely worth doing 👍🏽 If you’ve not already, please do like this video, stay tuned for some more content and thanks for taking the time to contribute to the discussion on this video 🙂
@rickgrafter 11 ай бұрын
nice
@everythinghome 11 ай бұрын
Thanks Richard 👍🏽
@problemslayer3538 11 ай бұрын
Not seen anyone treat an exhaust before, its an replaceable service part, unlike the chassis structure
@everythinghome 11 ай бұрын
Thanks, I understand - it seemed to work well - I'd rather protect what I can and replace as little as possible
@cappaculla 13 күн бұрын
@@everythinghome Seriously, Everyone don't treat the exhaust, for one thing they mostly rust from the inside out, also the extreme heat just burns off any treatments applied.
@everythinghome 12 күн бұрын
@cappaculla yup I agree with this and have revised this in my 1 year review video 👍🏽 kzfaq.info/get/bejne/hcBlfqyp393Spqs.html
@niceonejim3413 26 күн бұрын
great video, thanks. good idea to use a full face mask, but just fyi "throwing caution to the wind" would be to take a risk, ie NOT wear a mask.
@everythinghome 26 күн бұрын
Hi - Thanks for taking the time to watch and comment on this video. Glad you found it useful. Ah, you're right, thanks. I realised I'd made a mistake too on watching it back once published 🤦🏽♂️ If you’ve not already, please do like this video and stay tuned for some more content 🙂
@bm7760 4 ай бұрын
The salt on UK roads has a lot to answer for.
@everythinghome 4 ай бұрын
Completely agree, although somewhat needed for the snow (usually goes down too late though!)
@peteohead Ай бұрын
In the longer term (2-3 years), I have to say I was a bit disappointed by the hydrate 80 on my mk1 mx5 suspension and underside. I applied it carefully after a good wire brushing with the grinder and drill etc. It dried black, and looked amazing. Lanoguard hadn’t been invented, so I used Dynax UB over the top. Sadly, a few years later, I had to take it all apart and do it properly (blasted and epoxy primed) as the rust hadn’t been ‘converted’ other than a superficial layer on the top. It grew and grew underneath and then it was possible to flake it off in chunks. As a quick fix to ‘pretty up’ a rusty car prior to selling, this stuff would be good for disingenuous people like that, but otherwise, in the long run, it wasted time delaying the inevitable. On my next project, I am going to try applying lanoguard direct, after a similar wire brushing, and see if annual top-ups help keep rust at bay. It won’t look as black and clean but that doesn’t matter if it does its job as advertised.
@everythinghome Ай бұрын
Hi - Thanks for taking the time to watch and comment on this video. That's interesting to know. I'm just about to do a 1 year review. Mine looks pretty good after 1year but the front has held up better than the back. This year I'll just be topping up with lanoguard and making that a yearly application. If you’ve not already, please do like this video, stay tuned for some more content and thanks for taking the time to contribute to the discussion on this video 🙂
@Springwater786 Ай бұрын
I'm just about to coat my type R underneath with Dynax UB, it's suppose to arrest existing corrosion. That's not great that it continued to rust underneath, I'm hoping it will slow my rust down!
@peteohead Ай бұрын
@@Springwater786 It will slow it down…but not stop it. I was hoping that a really good wire brushing with the grinder, some hydrate 80 and Dynax UB would be a fit and forget solution but it isn’t. You’ll need to do it properly in 5 years time. Which is ok if your car isn’t a keeper?
@Springwater786 Ай бұрын
@@peteohead mines just light surface rust spots so I suppose it will be better than doing nothing at all. I'm using jenolite rust converter spray after a good clean and degrease then a coating of UB. Would do it properly but being a daily limits the options.
@peteohead Ай бұрын
@@Springwater786 Go for it mate you won’t do it any harm and it will look loads better.
@ratgreen 11 ай бұрын
Nice job. Did you notice any burning off of the hydrate 80 on the exhaust ? Some of these converters have a lacquer in them so they dry shiny, which I imagine would burn off on an exhaust. My only comment is you might regret using stainless bolts in regular steel threads, as it causes galvanic corrosion. I made this mistake a few years ago.
@everythinghome 11 ай бұрын
Hi - Thanks for taking the time to watch and comment on this video. Glad you found it useful. I did notice a little bit of a burning smell but it didn't last long. Thanks for the advice about the steel threads. I'll have to keep an eye on them when I take them out when I change the oil. I did coat them in the lanoguard grease before putting them in too so hopefully it keeps it all well protected. Time will tell 🤞🏾 If you’ve not already, please do like this video, stay tuned for some more content and thanks for taking the time to contribute to the discussion on this video 🙂
@stuartainsworth9335 4 ай бұрын
Replace rusty bolts with steel ones fully coated in grease before screwing in, then rust proof the bolt heads when tightened.
@everythinghome 4 ай бұрын
That's exactly what I did so good to know 👍🏽 should make things significantly easier later this year when I get the splash guard off 😄
@TheFootballDude18 5 ай бұрын
Great video! Thanks. Is there any point in treat my new car with hydrate 80, just a precausion? I’d like to do anything possible to minimize rust buildup.
@everythinghome 5 ай бұрын
Hi - Thanks for taking the time to watch and comment on this video. Glad you found it useful. That's a great question, mine was a 9 year old car and had a lot of rust so hence the hydrate 80. If yours is new, I'd just use the lanoguard which is the easiest bit 👍 Don't forget you can get £5 off your order with the link below snwbl.io/lanoguard/SHANAKA17034 If you’ve not already, please do like this video, stay tuned for some more content and thanks for taking the time to contribute to the discussion on this video 🙂
@TheFootballDude18 5 ай бұрын
@@everythinghome I’m from Norway so I won’t be able to buy LanoGuard, but I really do like the setup sith grease + the trigger sprayer. Wish I could get it here, everything is just aerosol cans here…
@everythinghome 5 ай бұрын
@TheFootballDude18 that's a shame, I'm not sure if buying it through Amazon may be an option. Norway looks like a lovely country. Would love to visit one day. All the best, Shan
@steeleybaws 10 ай бұрын
How much of the Hydrate 80 did you end up using? Aware that it's applied very thinly. (Might have missed if you mentioned in the video)
@everythinghome 10 ай бұрын
Hi Lewis - Thanks for taking the time to watch and comment on this video. I ended up using around 3/5ths of the bottle although the bottom of the Outlander was very rusty. A decent amount left to treat my other car which is a few years newer. If you’ve not already, please do like this video, stay tuned for some more content and thanks for taking the time to contribute to the discussion on this video 🙂
@ja4581 11 күн бұрын
What size ramps are those ?
@everythinghome 11 күн бұрын
These are them, all details on Amazon. Max height 18cm amzn.to/3XLuzMn (Amazon)
@carpgamer3986 6 ай бұрын
Does it dry black ?
@everythinghome 6 ай бұрын
Hi - Thanks for taking the time to watch and comment on this video. Yes, the bilt hamer rust converter goes black. The lanoguard cures clear. If you’ve not already, please do like this video, stay tuned for some more content and thanks for taking the time to contribute to the discussion on this video 🙂
@ar4732 Ай бұрын
They way you keep saying the product name, makes it sound like a total promotional video! BTW wishbones are far more likely changed due to ball joint issue rather than rust.
@everythinghome Ай бұрын
Thanks for the info, useful to know This was not a sponsored video and I bought the kit myself. They did agree to sponsor a later video though, a review of my Citroen spacetourer
Tyred Format
Рет қаралды 60 М.
To The Garage
Рет қаралды 6 М.
Repair Geek
Рет қаралды 2,4 МЛН
Apex Auto Detail
Рет қаралды 20 М.
Rick’s Garage
Рет қаралды 15 М.