How to Sync Mikuni Flat Slide Carbs

Рет қаралды 6,712

Shrop Shire

2 жыл бұрын

How to Synchronize Mikuni Flat Slid Carburetors

Пікірлер: 19

@kiddclofilm 6 ай бұрын

Thank you for saving me $450+. I finally got my dads 1100 back. Just put the carbs on and after I seen this video, its game over now. Thanks alot.

@strokerwatson4770 2 жыл бұрын

Awesome video my friend keep them coming looking forward to the next one

@mikemcdermott9589 11 ай бұрын

Great video. I just got some RS38s for my 2001 ZRX1200R. This video is gonna help a lot. Thanks.

@steveneastland4128 Жыл бұрын

I always use an egg carton when disassembling, then you have a little pod for each stage and a tray for larger components

@strokerwatson4770 Жыл бұрын

You need to post a video and let everyone know that you are doing ok my brother stay safe be blessed

@johnwhitla9191 Жыл бұрын

Good explanation. I am aware that these carbs are mean’t to sync’d off the bike but up until now I have used vac gauges with pretty good results. Looking at your vid though I will do a comparison and see which is better. I have some Flat slides on a Laverda Jota. I also wasn’t aware of the JIS screws so will get some. Thanks for doing the vid. Cheers John in Australia.

@AgentOfMadnes Жыл бұрын

Hi John, I'm in Australia too. Replace all JIS screws with SS Allen key, your life will be 10000% easier, and they look better And also only cost $10 for all the pieces. Cheers Ryan

@michaelkorolev2115 5 ай бұрын

This is a great video , I have RS34’s on my cb750 DOHC, the Mikuni owner manual thst came with my carbs says when syncing the carbs to use a manometer or similar device to sync the carbs, other than that this video is very good, I already knew about the JIS screwdrivers from a different video, and I really appreciate these guys mentioning the JIS screwdrivers that’s important

@jensvonbustenskjold Жыл бұрын

Thank you for an informative video! You are awesome !

@robertborland9222 Жыл бұрын

Wow! I need to call sudco . Seems easier after watching your video. Went out and #4 on 1983 gs1100e with rs mikuni had screw out( fell off?). Wondered how to get it back correctly. Found your video and bang! Got it running good again. Thanks, Bob

@michaelkorolev2115 Жыл бұрын

Thanks for the j I s screw driver tip I’m new to this have a 1980 cb 750 I’m putting mikunis on bikes are new to me gotta order a set

@userunknown303 Жыл бұрын

Awesome video! Taught me what I needed to know about adjusting my carbs As an aside, are these stock slides prone to chattering & breaking off into the engine like the TM38's? Are there aftermarket black slides you can install that won't shatter?

@robertborland9222 Жыл бұрын

Maybe add video of you now riding bike with happy performance! Thanks again

@seanaguayo Жыл бұрын

Good vid bro!

@dwightmason5430 6 ай бұрын

Did you ever get these tuned up and working properly? I'm currently trying to tune a set for my bike and was wondering if you have any further insight.

@whobru Жыл бұрын

Really good information for me. I just bought a bandit 1200. A set of 5020 carbs came with it the previous owner never installed. They almost seem like overkill...but I have no idea. Would you swap these with the original ones that are one the bike now? From what I can tell all it has are K&N and a Yoshi RS3 muffler