Thank you for making these videos fluff free and straight to the point. I appreciate the great job youre doing

Excellent video. Helped me eliminate the stator as my problem. Replaced $50 voltage regulator, problem solved. Thank you

Really appreciate you put all this in the video. Thank you.

This is very good. Clear and slow explained so someone unexperienced can learn. Good vibes coming off from the man

Thanx for doing this video.Gonna be checking my 2001 Dyna for any issues thatyou just demenstraited

Thx. Good details with the voltages and multimeter testing.

Simply.. You guys are the best..!! 👍👍

Always good info.

Thanks Patrick...very helpful 👍

The first test was a short test to ground, this is to test if one of the windings have a short to the chassis.

Thank you, this is avery good expanation of what is required to test the stator. It makes the job easier when the job is laid out clearly and simply.

good video. straight forward.

If you have an alarm installed on your bike & you don’t keep it on a battery tender or you don’t ride enough, or you don’t disconnect the ground wire, the alarm itself will drain the battery drastically. This kept happening on my Sportster 48 with a gel battery. In this case, get a lithium battery with a built in tester (BTS) and it will shut itself off after it detects low charging levels.

thank you this helped a lot!

Excellent video

Check your battery first, especially if you run a Buell XB12Ss like mine and have a fan that constantly runs, even after you shut the bike off for what seems like 5 minutes. This is good for the engine so it cools nicely and keeps oil passeges from clogging due to a hot motor and no oil circulation... but it sure tasks your battery something fierce.

Excellent video explaining everything. The one huge problem I have is that my bike won’t start so I can’t check that last test. Power goes on, speedometer doesn’t go on and nothing happens when I hit start. I tested the battery and it’s good. Its a 2007 Sporty 1200.. Any thoughts? Thank you

Great video

Thank you for this.

I'd check the charging system in this order - battery, regulator and then stator. Simply because that's the easiest and most logical flow. Battery most likely culprit and regulator can be tested at the same time by checking if voltage is holding, dropping or surging. If they're OK, stator is next and most likely the problem.

Thanks. Good video.

Thank you!

That's an excellent video! Guess what I'm doing this weekend :(

Thank you!!

Really appreciate all the videos and valuable tips you guys post! Thanks for sharing your expertise and saving us all time and money!

that was great. thanks

Excellent

First off, thanks for the video. I have a 2000 Fat Boy. It has 2 leads on the plug going to the regulator. When I do the continuity test, each lead to a bolt on the frame I get 1500+ instead of no change. Q: stater is bad?

My three prongs stator wire got cut two of the wires cut off from the front motor mount. Don’t understand how or why. Stator and regulator are only three months old. I’m going to check the stator like you showed. But the plug is no good and I can’t find a replacement without buying a new stator any help would be appreciated. Thanks

Thank you Patrick 🇺🇸

I have a 2019 Indian FTR that drains its battery while riding to the point of it shutting off every one in a while. It never fails to cold start tho. Manual Says the stator should be giving 27 vac at idle and 34 at 2,000 rpm, but im only getting 20 and 31 respectively. Is my stator that bad and needs replacing ? The regulator maintained the Battery at 14.5v, but dont know if the low power from the stator overworks the regulator and thats when my battery drains while riding ?

I have a 2002 Ultra Classic that has a 3-Phase Rectifying Regulator and stator I am just learning to work on my own projects how would I go about testing these two out everything I have seen deal with a plug in type. When I first start the bike up volt meter on dash reads at 12.5 and as it runs for a few minuets it drops blow 11 volt's i had fired up the bike let it run for about 20 min. one day and had the battery tested it showed it was good but needed a charge but when I test it on the bike and rev it up its running in the 14.5 range. it has stalled on me a couple of time when i cam to a stop one person rider is good two is a spit and sputter. any and all help would be appreciated!

How would I check using the same procedure if the battery is dead? I have a 2014 vrod muscle and it’s giving problems with charging system and it keeps damaging the voltage regulator.

shit, I got a beep. Im grounded out to the motor. Pulling the primary cover I guess. I appreciate your help. Now to find my black friday stator sale. lol.

Hi mate have a 08 fatboy and was wondering if lithium batteries are ok to use ? Will it charge correctly if everything is working correctly thank you

I've got a 99 S&s 113 I bought a new voltage regulator but even with switch off it's drawing constant power. Could that mean the stater is bad?

I have a 96 sportster stator checks out on test battery hold charge installed new voltage regulator. I am still not getting over 12volts at battery holding 2k and 3k rpms. Is there any other options.

Hi. Dyna 2001 FXDP I have problem with burning regulators.wiring ground and plus checked. I measuring at minimum stator give 20- 23V but when accelerating it rises above 75- 80 V. In 10 minutes regulator burning. Stator already checked and looking good. Please help. Cheers

Ok, it passed the first 2 tests , the AC output said open line no ac output. Any ideas on the issue.

Top 👍👍👍👍👍👍

If I pull out the plug from under my 97 flhtc how am I supposed to know which hole is A, which is B and which is C? Thank you.

I have an 03 flstf/I. It is making a kind of grinding sound after it gets warmer up. The noise is present when the bike is just idling with no rider on the bike. I mean it's sitting on the kik stand idling and it begins to make a hell of a kinda grinding sound with plenty of vibration. I thought it may be my cam chain tensioner. I replaced them but the sound is still there. It is coming from the driver's side of the motor and it seems to be coming from the front lower left hand side of my bike. Left is the driver's side of the bike. Could this be my stater. I can't think of anything else it could be. Since it does it in neutral while idling I am thinking it's not my clutch pack. I'm at a loss. Any help would be awesome. Thanx

Hi...how much volts should have the power wire to the coil? Thanks in advance.

I have a 2008 xl1200c, I keep getting low ecu voltage on my V&H FP3. Is that a charging issue, ecu or something else? It happened once or twice before, JUST tried to ride home and that's all it kept showing was the check light with battery indicator. Nothing ran badly though either.

So I just did a quick battery swap with a new lithium-ion and when I start it and look at my voltage it climbs to 16 and flip-flops in between 14 and 16 just letting it run do you know why??

I have an 883 2012 not charging the battery. But when I disconnect my stator from my rectifier the bike will not start so how do I check voltage

I got a 95 Harley Davidson dyna lowrider I have bought three batteries. something keeps killing them they run for a while and show charge when the back is off .do you think it could be the stator or the regulator my lite does go dim and bright at night I've noticed

There might be confusion here about the alarm during the continuity check. My MM gives a buzz when there is continuity and stays silent, but on 1 when there is not

At my diode test my multimeter just showed OL through all 3 wires. Does this mean my stator is grounded?

I have a 2004 HS6 Harley Powered Trike ..I recently replaced the battery & it ran get for a few days & then the battery is dead and I have to jump it to start it. ..as soon as I disconnected the jumpers ... it does ... HELP !!!!

Hye i got new stator for two times.. Now the stater voltage is 4.7.. What is the problem?

Does noise come from a bad stator or voltage regulator? I have a bike that just died and it was making a noise with the engine light and batrery light came on. When i was riding it it would make a noise when u pulled the clutch in and the ligjts dimmed. Is that the stator or th voltage regulator?

I installed a new battery. Rode for several hours, killing the engine and restarting several times. Last start battery was dead. Bike is 07 w/ 76500 miles. Volt gauge reads pegged out. Replaced volt meter. Gauge is the same!?? Gauge out?

So I’m not to confident in my results but my stator passed the continuity test and failed the ohm test. I tested the multimeter before starting and confirmed it was reading at a 0.00. Only one phase read at a 0.01. The other two phases read at a 0.00. I’m pretty sure that screams bad stator but a yes or no and some direction on how to move forward would be much appreciated. Bikes been kept in the garage for 3 months now and it’s just starting to get nice and cool out I’d love to get back on the road. Plz help lol.

If phase a to B & B to CY would you check C to be when you I have already checked b to c Shouldn’t you check A to. C

I have a Sportster. If I unplug the wire coming out of the stator the bike dies. Any ideas?

Why would my ultra classic keep burning stators? New voltage regulator, new battery and new stator?

Do you know why the teeth on a stator magnet would get sheared off?

Great video. Just learned I passed all 3 tests on the video. OK so tell me now please.. Does this mean my rectifier is bad? I'm not getting any charging at my battery..

Can I test it with main fuse out?

What series is your multimeter bosch

So I got nothing from a-b and a-c but b-c was fine. What does this mean?

Great video! When testing continuity, did you say you want to hear a beep (my meter beeps) to determine a good stater or did you say you wouldn’t want continuity (no beep)?

Sorry forgot to mention it's on a 2017 Street Glide FLHX completely stock no add-ons original battery from Dealer was in from 2017 until now,no other work done

Hi Patrick, may I ask how do we perform the test nr. 3 (the AC voltage) if the bike's not starting/running?

Hi, I have a 2000 Ulra that just died on me yesterday taking a short trip. I charged up the battery last night and today I performed the stator test as you show in the video. My meter shows that the stator is grounded on both sides which you say the stator is bad, but it is putting out 38 volts at 2000 rpm which is good. I checked the continuity between the 2 and there is continuity which is good. I checked the voltage at the battery while the bike is running and voltage is low (11.8v) and does not rise when revved up. Do you know whats going on here. Can a stator be grounded and still produce the proper voltage?

If it’s plus point 3 and you kept getting point four wouldn’t that be point 7 because you said add the resistance? That’s way over. Maybe you meant subtract

Hi . I have a 2015 ultra limited low. I tested my stator for continuity and I got an alarm sound from all 3 phases. But when I did the ac voltage output test while the bike was running all 3 phases were at about 30-35 ac volts. Is my stator bad?

🤘😎🤘

So what if it passes the first two tests, but not the AC test? I have a 2010 sportster 48 and the manual says 13.5 V at 2000 RPM, but other places online say that's 13.5 V per 1000 RPM, which would be about 27 V. Either way, I'm cranking out 31 at idle and up to 45-50 at a slight rev. Is that too high? It shoots WAY up if I really throttle it. Is that a bad stator? Great video! But it doesn't state what to do if the voltage is too high or too low. Any feedback is appreciated. Thanks in advance.

Hello!!! I have a 2018 harley davidson breakout M8. I burned the regulator. what I would like to ask you is: how much current must come out of the stator ??? measuring at minimum I give 20 V in alternating current, but accelerating it rises above 70/80 V. is this normal ???? Thanks in advance.

Key suppose to be in the on position for testing these?

A little confusing on the continuity testing. Continuity testing should be done with the beeper ON. You don't have to even look at the meter display. A beep across 2 leads indicate no breaks. Resistance testing, you would be looking for a value on the display. Thanks for the video.

MY 2015 HARLY IZNT FIRING !? . BATTRY HOT ! ? .

You didn’t mention to make sure the point at which your testing for a short to ground, to make sure it’s a good ground, chrome bolts are not a good point to test. Also you use the ohm position to test for a short, not the diode position, that is for testing diodes, but it does kinda work the same.

Test a battery always under load! A battery without a load always give's nice 12Volt but under load the bad battery's wil betray themselves. Also the alternator, always test them under load, take a big power resistor of about 10 to 20 Ohm, but be carreful, this resistor in gona get hot!! I cool them always in a bucket filled with water. measure the current and voltage, if all three are equal then the alternator is ok.

Damn 2 of the connections were putting out good voltage and then one was putting out 5.2....

So my bike did nothing on the second test. That’s a fail huh need a new stator I guess?

Voltage regulator not meter. Sorry.

Not trying to be a smartass, but my meter beeps at 0

Its not an "ohms" test it's a resistance test.

Poor job showing readings on the meter.

What if it's not running

Thank you!