A quick video cleaning a carb from a 1991 Polaris Trail Boss 250 4x4. Many Mikuni carbs function in a similar fashion around this time frame even the 300 350 400 425 500 Polaris atvs and four wheelers from this time era.
Пікірлер: 47
@GatorBuilt113 жыл бұрын
One of the best carb videos I have seen on youtube
@mikerisher15365 жыл бұрын
Thank you for the detailed video. Very helpful
@brandonmagnan464 Жыл бұрын
Perfect watch while sitting on the toilet
@joshskyeroberts65029 ай бұрын
Great video brother.!!!!
@ejr41402 жыл бұрын
great video ! thanks bro
@alexyoung3046 Жыл бұрын
Great video thanks for the help
@brianmoore36593 жыл бұрын
Good video!!
@alfredparise6 жыл бұрын
I'm having trouble too with 92 Polaris 350L, it would run really rough and shut off when using the throttle.I open the airbox and found mice had been living in there. I will take off carburetor and clean it like you suggested Thanks
@BrapStuff6 жыл бұрын
Sometimes mice get into the clutch cover as well. It may be a good idea to check that also.
@bryanfair53455 жыл бұрын
Awesome videos they are helping me replace the piston on a trail boss 350 I got it as a project and don’t know anything about it lol. Manage to get new piston in “top end rebuild kit”. Now I’m working on carb well since it was inside a bucket I don’t exactly know how to hook up the throttle slid peace. Could help me ?
@osbornebay9442 жыл бұрын
Super, my carb behaves like you have to open quiet a lot for it stays idle, if l starve fuel supply, engine racing up. l felt it runs on chock fuel. l ll follow your instruction to do a good cleaning.
@jequinlan35 жыл бұрын
Anyone have info for vent tubing routing? Carb and tank?
@ds77chevyrules4 жыл бұрын
Hey bud i just got the new piston and jug for my 1990 trail boss it has troubles starting when your turning it over it will fire up halfass but wont stay running need help
@austineverett63842 жыл бұрын
Awesome video but o didn’t catch where you adjusted the carb at all
@BallisticVolts6 жыл бұрын
im having trouble with my 96 polaris explorer starting slow and always dying after the first start then taking forever to start again. eventually when it does start it runs great but recently its been dying at full open throttle. any advice? it has pretty low compression but im not convinced thats the only problem.
@BrapStuff6 жыл бұрын
It's sounds as if there are multiple issues going on. If on cold starts using choke it starts then dies and is hard to start again that sounds to me that it's getting too rich and flooding out. I would try starting with choke, with out, and by squirting gas directly in the carb. See how that affects the start. As for wide open throttle having it die, I have seen plugged petcocks starve the carb. You may want to pull the fuel line and check the flow on and res from the petcock.
@BallisticVolts6 жыл бұрын
Brap Stuff I thought it was flooding too but not experienced enough to know. Thank you so much for the help!
@davidjones60924 жыл бұрын
I have an 03 trailblazer with a similar carb. I just went through everything and cleaned it good, put it back together and it won’t start without adding gas straight into the carb. Once I get it started I have to keep it at high rpms to keep it running but as soon as I let off it dies out and won’t start again. Do you have any ideas?
@shawnr93574 жыл бұрын
Did you get it figured out??? Mine is doing the exact same thing?
@coreyrides96504 жыл бұрын
@@shawnr9357 the bowl probably isn't filling tap the bottom of the carb and blow into the gas tank
@truthseek30174 жыл бұрын
@@shawnr9357 turn the bronze air screw to the left or the big idle screw to the right.
@easydoz14 жыл бұрын
Make sure your not losing spark at no throttle. They have a switch in handle bar throttle box. If throttle cable breaks it kills the engine
@jasontrevino20652 жыл бұрын
how do you remove choke cable from carb? i’m having trouble taking off. thanks
@JohnDoe-pv2iu Жыл бұрын
It came off easiest for me with two tiny wrenches. The big nut seemed stuck until the little one was loose. That isn't how it works though. I was just not getting a good grip on the big one and think breaking the little one loose helped loosen the big one...
@nunyabidness69733 жыл бұрын
What is the big jet with spring on it by the air fuel mixture???
@ljohnson10083 жыл бұрын
Idle
@nathandegarmo42884 жыл бұрын
I got a 92 trail boss it starts and runs then after 10min it bogs down and won't fire back up till it cools down any ideas
Ok she runs great now and nowI have a loose chain and it keeps popping off the sprocket and I have no clue how to tighten it and to be honest I think I've bitten off more than I can chew but I'm slowly figuring it out lol
@lamarzimmermanmennonitefar52694 жыл бұрын
@@nathandegarmo4288 there's two bolts on the back of the axle to loosen, and you rotate the axle Barrel and tighten the bolts again
@williamtarr97584 жыл бұрын
How many turns out for the air fuel screw
@BrapStuff4 жыл бұрын
Start with 2 turns about adjust half turns if needed.
@daltonray7964 жыл бұрын
Brap Stuff I got a 1993 trailboss
@BrapStuff4 жыл бұрын
@@daltonray796 Niiiiiiiiice braaaaaaaah!
@Chuckseese Жыл бұрын
You didn’t take out the main jet though
@trojanman225 жыл бұрын
do you know the model of this carb?! its exactly whats on my 2001 trailblazer and i dont think it should be....
@BrapStuff5 жыл бұрын
I believe the part number for this carburetor is 3130424. It was used from 1991-1999 I believe. It would likely work on the trailblazer, but you may need to rejet for best performance.
@chasefreeman14925 жыл бұрын
my trailboss will start up and rev to the moon and the throttle barrel is closed
@BrapStuff5 жыл бұрын
Sounds like you have an air leak somewhere. Intake, crank seals, or base gasket are all places to check.
@chasefreeman14925 жыл бұрын
@@BrapStuffok thanks
@MRblond72 жыл бұрын
I wish you would’ve shown reassembly. How do I know How take to go on air fuel mixture and the idle screw?
@BrapStuff2 жыл бұрын
Follow the Polaris spec for your machine.
@MRblond72 жыл бұрын
@@BrapStuff Where can I find that? Players Xpress 300 1996
@BrapStuff2 жыл бұрын
Call a dealer and talk to a service guy. Ask nicely. 9 times out of 10 someone nice will help.
@MRblond72 жыл бұрын
@@BrapStuff thank you for the reply!
@Tater42004 жыл бұрын
woulda been nice to see the float height adjustment.....
@BrapStuff4 жыл бұрын
...parallel to the bowl mounting surface! Tip the carburetor upside down and check.