My Acura TL 2006 had VSA light on after a minor bodywork on the drive side door. The body shop couldn’t erase the code. Acura dealer asks $255 for a diagnosis only. This video solved the problem in 5 minutes! Thank you!!

Thank you!!! I have been using a Innova 3130c...it did NOT have the function that permitted doing the neutral position. My dealer told me the VSA module had failed and it would cost upwards of $2,000 including labor to replace it and get rid of the VSA light because he and the mechanic had determined the VSA Module had failed. After watching this video I elected to take your advice and go with a Foxwell from Amazon. I checked out several of the models and went with the Foxwell NT510 elite that is pre-programmed for Honda/Acura making sure it did ABS and SAS. Two days later, June 11, 2020 it arrived. the next day I successful got rid of the VSA light. VSA switch working normally. A light rain soaked a vacant parking lot and I tested ABS and VSA control.......both worked. THANK YOU!!!!!!!! My Car: 2005 TL with 6 speed and Brembo's. Mileage 289K. Tomorrow I'll replace the Canister Purge Solenoid with an OEM part. Having watched your video I feel certain that is my Check Engine light issue. Thanks for using Foxwell during your video presentation! The Foxwell 510 elite is intuitive and very user friendly. Much nicer than my older Innova; Today 6/15/2020 I received a Canister Purge Solenoid valve from Amazon. Original Denso was made in Mexico, this replacement Denso was made in Japan. Took 30 minutes to replace it, I'm a novice,. I turned the key on, no faults were showing and the ck engine light was gone. I didn't clear anything. But I did disconnect the battery for the install, so the ECM had cleared some of its codes....guess this was one of them. Thanks again!!!

I made the mistake yesterday of not plugging back in the mass airflow connector before going for a ride. Almost every warning possible lit up on the dash. It took a tool like yours to clear all the errors so i could get an inspection. VSA was the most difficult to clear. Who would ever thought how many things a disconnected MAF could have. :-) (2008 Honda Element) I had just bought this vehicle three days before. Man, was I cursing the seller. LOL

This procedure can also be done manually without a scanner. In the ODBII port with the ignition off you must install a jumper from pin 4 to pin 9. You then turn ignition to the 2 position. As soon as the ABS light goes out press the VSA OFF switch. As soon as the ABS light comes back on press it again. Remove the jumper you put in and start the engine. The light should be gone.

One of the few KZfaq fixes that actually worked.

Wow.. big thank you. Acura wanted 1200 to inspect and reset VSA system. Followed your video and saved over 1000 bucks! 06 MDX.

Bought the same tool. It worked! Vsa and tpms light would stay on my cousins 17 Accord Sport. Finally helped him turn the VSA light off.

Just wanted to say thanks for this. Bought the exact scanner you have in the video and i was able reset the VSA light on in my 2005 Honda CR-V. Also, this is a much nicer scanner than the other, cheap, one that i have. It has a ton of really nice features, can even bleed the brakes using the ABS pump. Sweet. Thanks again for making this video.

Thanks a TON for this! Saved me a bunch of cash, and eliminated a very annoying message on our 2005 MDX. Really appreciate your advice and walk-through! Thanks!

Thank you. I have the same scanner. With my iPad in the car I watched your video and after 2 years I no longer have that triangle.

I have tried many 'fixes' for this issue and the SRS light on my 2005 TSX, this is the first scanner and fix that actually resolved my issues. HUGE thanks!!

100% totally works. Happy it works. Thanks. Got the 630 and it worked with it on the Honda Pilot 2005.

I have a Acura TSX 04 and that same problem and I bought a scanner to find out what is happening since my car passed the inspection and everything but that light did not appear for a while. thanks for that detail! I have saved a couple of dollars in my pocket

Thanks! Fixed my 2006 tsx. Techs at a few shops in town told me I needed to take it to an Acura dealership about 100 miles away to clear the vsa light.

this is an excellent tutorial. i bought the exact tool, fixed it just like you show. thanks for taking the time to do this

Outstanding! Ordered via Amazon this morning, delivered at 1:30pm, Problem Solved!! Thanks Man!!

Thank you for your vid. I was so lost without it. I finally was able to get the lights to go off.

I tried this on my 2005 Acura RL and it worked like a charm. Thank you.

OK it's been 2 years since you made this video. What is the best and cheapest scan tool now a days that can reset VSA and abs?

Dude you are the best. Bought the same tool, cleared the code with same procedure that you mentioned. VSA system works now when i floor it from a dig. Bought my car used with bad battery guess thats what caused the issue in the first place!

THANK YOU! I wish I had found this video before replacing fuses, blowing fuses (Stupid thing on my end) and being totally frustrated, purchased the Foxwell and had the VSA reset and working normally within an hour of its arrival on my 2006 Acura MDX that had recently had the transmission replaced (And the transmission shop wouldn't try to figure out the VSA issue)...

Thank you!! Bought one. Followed your steps and it worked. So grateful 🙏

I purchased that same scan tool (only difference is I didn't update mine like you clearly stated you should) but it did clear my ABS, vsa, and the ! With the orange triangle. But it didn't have me spin the wheel from one side to the other. So naturally when I tool my vehicle for a test drive all the lights came back on. But I'm going to say that's on me (operator error) as I too have a 2006 Acura TL and boy was I happy when I saw all the lights cleared out. I'll definitely update my NT630 scan tool, take my vehicle to a flat surfaced parking lot and try this again. Hopefully it will not just turn them off but keep it off. Because after following the steps on the video I had thought all was well and even ran a scan but had no fault codes. But the recent changes I've made was the car had 20in rims and when I bought my new 18in rims I made sure to have new TPMS sensors installed so I thought maybe my car and those new sensors in the wheels weren't calibrated right. But I'll keep you updated. However I do love this scan tool as i perform my oil changes on 2017 Mazda CX5 and getting that orange wrench to turn off after doing my own oil change as was a pain but using the NT630 it was a breeze so I know the scan tool works as it's supposed to.. but I guess I just need a flatter surface to run the vehicle on when trying to fix the vsa problem

Thanks so much for making this video man. It did turn off my VSA light on an 05 CRV. I had 2 mechanics look at the car 1 said idk and the other started BSing and wanting me to change a bunch of stuff.

Dude you saved me a lot of money .... My pilot 2011 had the same issue after I sent it to the body shop they let the battery died and for some fkn reason abs and vsa ON// i called Honda Canada and they wanted just for inspection 189.oo+tax ... I found in Amazon the same tool and just plug and play // following your video I removed the fkn light 🚦 thank you

I have a very expensive autell scan tool it can't do it oddly lol so I ordered that tool u used and 2 years later $140 down to $100 I got it for $109 after taxes brand new should be here today and I hope it works for this 06 TSX same issues and everything is working properly fuses are good etc appreciate this vid 😀

this $140 scanner is sweet, my Autel Diaglink does NOT cover steering SAS. VSA light can be fixed for free with a simple wite jumper in the OBD plug during the VSA reset procedure. My VSA Fault was caused by battery removal and OBD2 reset.

I put in the VCMUZZLER 2 and my vehicle instantly ran better no more vibration and no more check engine light or VSA light on

If someone has a problem shortening pins and car won't turn on check the fuses for pcm ecu or acg

Are the tornado sirens going off in the background? lol

Man this video did the trick. I followed your video step by step. Light is finally gone ?? Thanks so much

Worked great on my 03 MDX. Better than other videos on the same subject.

Last summer VSA, CMBS, ACC, and Air bag lights came on. We’ve checked each of those and fixed all issues but the lights wouldn’t go away. I ordered the tool you use and it got rid of my VSA light. My question is, is the process for clearing the other lights the same as the process for clearing the VSA light? I don’t wanna screw anything up! Thanks!

Do you have any clue if this process would work with a Foxwell NT604 Elite scanner?

After 3 years of this video being posted, I'm pretty sure you know this, but imma say it anyway, YOU DA MAN!!!!!!. help clear that code off my 06 Acura tsx plus I know have a reliable scan tool. Thank you

The Autel MaxiAP AP200 works also. It's a 2 step process but it works. On Amazon $62

Thanks soo much for this video you saved me from replacing the ABS pump which i really didnt really wanna mess with i would clear the code and as soon as i hit 30mph it would come back , i never went into control modules and that did it , this is on a first gen Acura Tsx

Thanks! Worked on my 2013 Honda Pilot EX-L.

This is So awesome!! My friend will be ecstatic to know this! Thanks a bunch!!

Thanks for making this video, work on my 2006 Honda Pilot

Thanks buddy... i was thinking the worst

I got a ODB 2 reader . Paid $40 bucks 4 years ago and it works perfect. Clears all codes . ALL CODES. I Have 2 Hondas with VSA and it clears it and done . Dont believe that BS that u have to spend THAT much for one.

So if I hit a pothole hard or maybe a speed bump the light comes on?

I have the same car and scanner, I just went out and fixed the issue. thanks a whole bunch.

awesome, thank you. this worked with Autel scanner as well. No more anoying light!

Man that scanner really fucks well

Worked perfectly for my 2008 Acura TSX! Thank you so much!

Well, I wrote and re-wrote all the steps you performed. There is one difference between our two NT-630 Plus scanners. Under Special Functions, my unit has four options - 1. Pulser Test, 2. Mode Clear, 3. All Sensors and 4. VSA Sensor Neutral Position Memorization. In following your procedure, I failed. In following the # 4. VSA Sensor Neutral Position... it also failed. Perhaps the lights can't be shut off if there is a real problem? I do have two codes - 66-1 and the 84-1. So I guess I'll have to put up with the lights until I decide to repair or replace the ABS module behind the right, front headlight.

mine wont let me clear one of the codes. 18-19 it says and then 18-13 when i go into the DCT. ECM/PCM relation failure or something. im so stuck figuring this out. it all started after i replaced the clutch myself. I must have hit something reinstalling the transmission.

Thank you! I was able to fix my issue as a result of your guidance.

Snap on scan tool works also, Jus had mine recalibrated on my 06 TL

Works like a charm, thank you

Also could be a wheel speed sensor

You’re the man. Worked. 08 TL!

I have 09 crv but I have egine light and vsa what do I do?

I purchased the same scanner and cleared codes except the 8401 and tried the visa sensor but tak memorization but mine loads for a minute but then says no communication. The scanner reads dtc codes or anything else but won’t do the visa reset

I see recommendations for the Foxwell NT630 Plus and the Foxwell NT 510 to turn off those VSA lights. For some reason the 510 is more expensive than the 630 and only works on one vehicle make. I'm assuming it might have some more or better functions than the 630 but not sure. So, why did you pick the 630 Plus? Price?

Thank you very much for your help it really helps me out a lot

It worked! Thank you very much!❤

Or try a paperclip in obs2 pins 9 and 4 then ground pin 9 , look for a video on how to do it .

Thanks a lot bro. I appreciate your knowledge. God bless you

Thank you so much. I was about to lose my mind.

why VSA OFF key has no effect? thanks for your video.

0:53 😂😂😂 Very Slick... Fukswell Btw... 😅

Hey bro, I know this is an old video, and I just got a 2008 Honda Accord and the VSA LIGHT came on . I will try this tool and let you know 🙏🙏🙏

Do most scan tools for Acuras TSX (2008) going to have a VSA option under control modules? Also, how do you diagnose with the scan tool something is actually wrong with the VSA before reseting,? How do you know what triggered the VSA light to come up in the first place?

Anyway to get rid of the VSA light without a scan tool? Between the NT630 & NT510 which is better for an Acura TSX 2008? Thx

Thank you for your video, got a question, I also got the ABS light on. Any idea? I was able to clear the code, I got a NT650Elite Foxwell scanner. My beloved car is an Acura TL 3.2 2007, thanks.

Does your scanner also have the TPMS function?

The best video

How in God's name did you ever figure out how to do that? I started out in OBD II, I think, and cleared all my codes and then went to SAS. Didn't work. I figured maybe it would be better to come back to your video and write down step by step what you did. So I gotta start with ABS/AIRBAG to scan the system, clear the code and align the SAS all without leaving the ABS/AIRBAG section. I would never have figured it out on my own. I'll give it a try tomorrow. Thanks.

U da man bro! 🎉

Is it safe to drive after this procedure is done?😊

Great video! Thanks! Will this also work with the NT510 with Acura/Honda software loaded?

Thank you

Does the vsa button click and stay in the downward position or is it supposed to spring back? Mine does not stay held down.

Oh I thought something was wrong with mine. My icon is that triangle too. I thought it was supposed to be another icon like the cat drifting. So when I turn my VSA off the triangle light comes on so that's normal? And when it turn the VSA on the triangle light come off

I have a question that maybe you can help me with.. I have a foxwell scanner NT650, I’m trying to reset my vsa light but for some reason it’s not letting me. It tells me that the abs/vsa does not work during test mode! I also try going around this, but then it tells me that it can’t communicate with my vehicle?! Any suggestions??

I have an Acura tl 2005 that has an abs vsa triangle exclamation point lights that come on with a check engine light that is supposedly a gas leak, they come out randomly and I just switch my car off and on again and everything goes away except the check engine light, what can it be ?

Hello my abs and vcs and sh-awd lights are on but not the check engine light on a 2007 Acura Mdx do you have any suggestions where I should begin as I am not a mechanic and don’t have a lot of money any help is greatly appreciated ty

Nice demo, problem solved.

Sounds like you have the 4 minute nuclear attack warning going off in the background... er...probably too late to tell you now.

I have a 2004 acura tl and my vsa light works t stay off. My friend has a pretty device it shut it off, but when I went down the road it just came right back on again. He didn't straighten tires up or turn steering wheel he just did diagnostics. Like I said it turned ou off but came right back on. Do wheels need to be straight and DC o you need to turn steering wheel us that important? Please help

Thanks!

Just bought the same one and updated and says no communication

Can i use this scanner on an Acura RL 2008?

I had vsa triangle and abs lights come on after getting some rusted wheel bolts changed on my MDX. I managed to remove the abs light and vsa. The triangle never left and after a couple minutes of driving the vsa light always comes on and later the abs. Ive now bought this scanner hoping it’ll clear my problem

Ive got a nt604 and i dont see anything like whats in this video.... i cant get my vsa warning light off

I've got a 05 TL which was in the front end low speed collision. The airbags did not come out but the yellow triangle light, VSA light and airbags light stays on constantly. Do you think getting the airbag module reset will eliminate all these lights ?

I just had a timing belt replaced on my 08 tl 3.2l and there was no lights on and vtech worked fine when I dropped it off. I got it back and the vsa and triangle light are stuck on and vtech not working. Please anyone help me with some suggestions

Vsa light stays on wont turn off. My buddy has a pretty good device but we did not turn steering nor did we have wheels straight he just hooked up device and light went out like I said it just came right back on again please help

84-1

Why doesn’t my scan tool have the special functions I have the same one

Super video

Hey there! I'd like to try this for my 2013 Acura ILX, but my VSA/ABS, BRAKE, HILL ASSIST, and POWER STEERING lights all come on and I'm not sure if it will address all of these things. I brought it to an Acura dealership and they replaced the VSA sensor for $90, but I drove off the lot and all lights came on again. Do I need to just pay the $3300 they're asking for to replace the VSA modulator, or should I try this? Would love your input!

Can you use on any vehicle

I have a ‘13 TL and my VSA light as well as my uphill assist light came on, hoping to get this cleared ASAP. I saw someone say that oreilly’s scanner won’t clear these codes, is this true?

Hi do u know if the NT301 will do this too please?

Can this scan tool run idle relearn?

Will this work with Acura TL 2004?