HOW TO WELD AN AXLE TRUSS - Project Maple Leaf Jeep Build (no. 15)

Рет қаралды 6,497

Жыл бұрын

In this video you’ll learn how to weld any axle truss onto any axle. The tips and strategies in this video will help you successfully install an axle truss on a front or rear axle, anything from a Dana 30 to a 1 ton. You will also understand how to set pinion angle and adjust brackets to properly line up that axle swap truss.
Please SUBSCRIBE to show your support! It’s FREE and allows ne to continue building things to provide you guys with good content and work toward the vehicle giveaways!
Check out my website to see the brands I choose to support!
WarPaintoffroad.com
***Disclaimer*** This video is just meant to show how I do it. Injury may occur by trying to replicate what is in this video. Attempt at your own risk, with proper equipment and training.

Пікірлер: 22

@Labergemusic 11 ай бұрын

This video is a treasure trove of information for me. I'm about to build a truss for an Explorer 8.8 into a Gbody and I got a truss kit with a single page of instructions. I already learned about instant center/pinion angle but your talk about heating and cooling the welds is huge to me. There's a bit of everything here and I feel like I actually understand what I have to do to make sure this is adequately welded together. Really appreciate this content.

@WarPaintOffroad 11 ай бұрын

I’m glad it was helpful. I also just did another video that might have some more information about welding it better. It’s a front truss on a Dana 60 from Artec…but the same info applies. There are some other ways to do it…but this is the most time efficient way. Have fun with it. If you have any questions I usually Dan respond faster on Instagram @WarPaintJKU.

@alexmacksey4510 9 ай бұрын

Getting ready to truss my JKUR. Great video!

@WarPaintOffroad 9 ай бұрын

Awesome! Have fun! Let me know if you have any questions!

@thatjeepkid2305 Жыл бұрын

Sweet! That baby on the counter is creepy as hell! 😂😂

@WarPaintOffroad Жыл бұрын

Hahahaah. Isn’t it!

@full_metal2452 Жыл бұрын

Great video 👍

@WarPaintOffroad Жыл бұрын

Thanks for the support!

@671JK 3 ай бұрын

Awesome vid! Can this be done with a stick welder and 7018 rod?

@michaelgarcia6580 3 ай бұрын

Yes, 7018 would be a great way to weld on these axles! 7018 would be fine for the brackets and tubes, pulling the axle out from under the Jeep and putting it on stands so you can weld everything in a flat position (95-120 amps 1/8 7018) would be best. And for the center section, preheat to around 450-500 and use a nickel stick welding rod, and be sure to post heat the mild steel to match temp to the nodular center section

@671JK 3 ай бұрын

Thank you!

@WarPaintOffroad 3 ай бұрын

Sorry for the delay. Like said above….definitely. I love the detail the above comment gave. That’s what makes this community amazing. I wouldn’t have been able to give you that detail for stick welding. But it can definitely be done. I have seen it done that way.

@michaelgarcia6580 3 ай бұрын

@@671JK you might have good luck with 3/32 7018 in certain areas too, 1/8 might be “too big” for certain spots. I’d use around 95-110 amps for 3/32

@michaelgarcia6580 3 ай бұрын

@@WarPaintOffroad I learned how to weld using 7018, so it’s kinda second nature for me. I was on the fence about whether to MIG weld or if I could stick weld my truss and c gussets on, I would have to buy a mig machine for the mig or I could borrow my buddy’s stick/tig machine for free.. so I think I’m gonna go the stick route.

@dextersuarez9948 8 ай бұрын

What setting did you use? Wire? Etc.

@vincentmamotos9937 Жыл бұрын

hey warpaint, were you on a 240v outlet on that welder? harbor freight has the titanium 170 mig welder. You think thats good enough to handle the job? Was doing some research for welders and I wanted to get something good to weld on this thick .5" axles

@WarPaintOffroad Жыл бұрын

Yea! 240 for sure. The smaller stuff just can’t weld as thick.