Journeyman electrician here. I work for a company that specializes in whole-house GENERAC generator installs. I've literally done this install at a customer's home. What I did was I installed a wire way under the two transfer switches. I took the generator cable from the generator to the wire way, and took the splices I made in the wire way up to E1 and E2 terminals of the two transfer switches. For me it's a cleaner install because the 4/0 aluminum or 2/0 copper service conductors take up a lot of space in the transfer switch. So the wire way just helps me keep the transfer switches from being overcrowded with conductors. I as stated by a previous post, I've never read or talked to any GENERAC representative who said those lugs were rated to have two conductors terminated in them. I would much rather use Polaris taps. I do like the GENERAC tray cable that has both the control wires with the power conductors grouped together. I like that it's direct burial, and we can purchase the cable in either aluminum or copper.

as a Generac trained tech, I can say those contactor lugs were not rated for 2 wires originally and if they changed something recently it would state that in the manual or on the lug. Best to install some insulated wire bugs to make the branch for generator load wires. Also, while working on the signal wires, disconnect the molded plug (white connector) at each module to prevent accidental powering of contactor solenoids too early in the game. Those load-shed modules must be used with central AC units, and they can be wired directly in series with the 24 volt AC contactor circuit. (at the air handler or outside unit) The modules have a preset time delay (3 minutes) after a power failure to eliminate multiple hard start attempts under high head pressure. They are marked "unit 1, 2, 3, 4" and each has another delay (spaced apart) so things don't restart all at once while the rest of the house is coming on-line. Best to wire all the AC units on the same module or you will have two AC units starting at the same time. The nice thing about the load-shed system is it's smart enough to watch the gen load (via frequency) and if the load is too great, it will shut down the last load for 5 minutes, then try again. It will do that 3 times then wait 20 minutes for another attempt. The idea is to allow another heavy appliance (water heater or well pump?) to finish a cycle. That load-shed is only rated for pilot duty, so any heavy loads like a pump or water heater must also have a relay system to tie into the module. Generac sells relay kits rated for these things, if necessary. Oh, Generac just upped their game to 26kw on the air-cooled sets. I don't think any of the other major players has an air-cooled that large.

Great work and information.

I’ve done several of these. The schematic only shows connecting the white and red low voltage wires to the second switch for transfer. Learned the hard way. The black ground wire must be present to the second switch for automatic transfer. Generac didn’t suggest this through tech support. Great job coach.

Hi from Southern California Thanks coach ✌️👌

Best video yet great examples

Thank you for this great material and explained very well.

Great video. Thank you so much. I have been trying to understand this setup for months. This was very clear. You explain things very well.

Thank you, I'll be installing one soon..

Thank you!

EXCELLENT INFO Thanks Bruh !!!!!!!!!!!

Thanks

Awesome lesson Thanks

Hey code coach, please explain to me how can you back up (2) 200 amp panels with a 100 amp generator? Are you using alot of SMM and load shedding? The nec says the generator has to be capable of carrying the full calculated load applied 702.4(B)(2)a. Thanks for any help in understanding.

Very good explanation...

Question I know the lugs are probably not rated for a double tap but is it okay if I add a surge protector onto the load side lugs double tap it with the panel load wires on the lug. What’s the correct way to install a surge protector in a generac ATS

Thank You Coach It was Really Helpful What is the maximum distance between Generator to the meter base or transformer Switch ?

Great video! I think that would give me an answer to my problem, l have all the communication wires on both transfer switches, instead to connect only the black,white and blue wire between transfer #1 and transfer #2, l think thats the reason why fuses n1 on both transfer switches are blowing out.

In the case of a 320 meter base with parallel lugs (2 200a panels) is there any nec rule against putting one panel through a 200a t switch and leave the other 200a panel fed straight from 320 meter base?

If a lug is suitable for two conductors is is clearly marked on the lug......one indication is if the lug is oblong it will be rated for two conductors. Normally 200 amp load centers will not be supplied with 2 conductor rated lugs as only one conductor will accommodate 200 amp residential load center panels. Panelboards rated 225 amp 3 phase, and larger are common for two conductor terminal lugs.

Do you have a video showing how you would incorporate a 400 amp disconnect when there is a disconnect combo with (2) 200 amp disconnects? Does this require two separate 200 amp transfer switches?

Do I need separate ground rods for each transfer switch?

Another one,i have two 1.5 ton and two 3.5 ton ac with 4 furnaces, dryer,fridge,stove,light,and more on two 200A panel can put all things on 24kw generator with 2 transfer switch and one generator as your teaching?24kw can hande it all my stuff? Thanks again

Grate video, I have question.my meterbase is 400A from hydro side and I have two 200A panel can I use 400A transfer switch for both?and I want to buy two 22kw generator one for each panel 400A transfer switch can handle it both generator at the same time? Thanks

did you ever make that video with the Meter Main Disconnect combo?

👍👍

22 kw is the biggest one ive installed. Do they make a larger generator that would be more suitable for a 400 amp service?

What size all in one wire for the new lp 26 kw Generac

Why bond if house is already grounded it is ok with just house ground before what changed so much I couldn't just ground normal

What about one panel, one generator and also solar together?

Pretty sure i did this with (1) 400a transfer switch, no?

Why not just one 400A transfer switch?

Why use 2 200Amp Transfer Switches? Generac makes a 400Amp transfer switch.