For more helpful videos like this please consider supporting my channel by either subscribing to it or giving a Super Thanks. Your support helps to enable me to both create more content and improve the quality of it, via the acquisition of new camera equipment, editing software and purchasing subscriptions to quality royalty-free music.

After all these years, this video was extremally helpful even though the video quality was poor. So hard to find videos for Half Hot using 14/2 wiring. Thank you!

You sir saved me a whole lot of money. I spent forever scratching my head here and found your video right before calling an electrician. Everything was wired properly but nowhere else I looked mentioned snipping the brass piece. Thank you!!

Great video and I followed every step. I made sure I watched it twice, then paused it on every step the third time and went and did the connections one at a time until it was finished. Worked like a charm. Thank you so much for putting this out there, even though it was 9 years ago. Awesome!

THANK YOU so much for this video -- I didn't have the right tool for cutting the brass but I made due with one of my scrapbooking tools! Videos like this are such a blessing for us stay-at-home moms looking to make our job as homemaker a bit easier and less expensive!

This video was very informative for my new dishwasher/disposal outlet installation. Saved me a lot of money and taught me plug and switch basics. Thanks Mark.

Thank you very much! 12yrs later and still helping people

Thanks. You solved a headache for me. I did not know about that plate, and changed the outlet. I could not figure out why the switch did not turn off and on. After this video, it took me two minutes and everything is fine.

Thank you. I replaced old outlets wired in 1985, and did them wrong, where the switch stopped working, and I was also mistaken in not snipping the brass tab. I used your video to get an idea on how to correctly terminate pre 2011 wired houses. Whoever did mine did not bother to use black tape on the white wire.

Thanks Mark! My dad and I were stuck and knew all wires were hooked up correctly. That little brass plate was the trick! Awesome.

@HomeAdditionPlus Mark, I completed the work on the weekend. Everything worked out great. Thx for your help.

As soon as I heard snip the brass buss plate it came back to me like a thunderbolt. Learned it in high school and haven't needed to do it in 30 yrs. Thanks and great video!!

Thanks Mark that the Best Video I seen on how to do a Half Switched Outlet THANK AGAIN

I had to replace the old outlet in my living room and couldn't figure out why the switch was not turning the power off to the bottom outlet like before. Your video showed me exactly what my problem was. The outlet is now working as it should! Thank you sir! 😂

Literally saved my life tonight. This video was so helpful!!!

Thanks so much! Helped me avoid a big problem

Sweet, simple and easy!

Thanks Mark! This was clear and helpful.

@twopintpete - The same power feed that powers the switched outlet can also drive the power to the overhead light fixture. Simply run a 14-2 romex cable from the light fixture to the outlet and attach the black wire of the romex cable to the feed side of the switched outlet and then attach the white wire of the romex cable to the white return on the switched outlet.

I enjoyed your video. It was very helpful. Thank you!

Thank you for making this video. My New Years resolution is to stop doing small home electrical work without flipping the breakers off. You'd think after getting zapped so many times as I'd stop playing "operation."

Ok. Now I understand why mine wasn’t working when I replaced the receptacle. I need to cut that connection on the hot side. Never noticed that. The house has red black and white. Thanks for making this easy to follow.

Excellent job in explaining,as well as, production and cinematography!

Very good video. It was very informative. Ty

Thank you sir! Saved my bacon... Easy to follow instructions, issue solved.

Wonderful video! This was one of the only videos that was easy to follow. I have a follow up question (for anyone): Can I use a timer switch in place of my single pole switch? I have the EI220W Intermatic timer. I have a red (load) wire, white (neutral) wire, green (ground), and black (hot) wire. How can I get this to work? Thanks!

It's ok to do it like this if you're a homeowner, but most electricians won't do this because it's been a code violation since 2011. You would need to use 12/3 or 14/3 and leave the neutral wire capped in the switch box for the possibility of upgrading to a Wi-Fi switch/dimmer. Incidentally, you could also tap into this switch box to add a receptacle down the road. When you come across a switched receptacle you need to know if you're working with 2 circuits or a single circuit as either situation is possible.

Thanks for the helpful tips. My son's room is currently wired exactly how you described in this vdeo. There is no overhead light in the room. They only light comes from what is plugged in to the outlet that is controlled by the switch. I would like to add overhead lighting that will be controlled by the light switch. Can you describe how and where I would connect the wires? Thx...

Thanks you best explained video on this subject

great video!!

@PM3520 One reason might be that switched outlets are often mounted upside-down to indicate that they're switched, as in apartments. I don't know if this is a widespread custom or something that's done in the industry; I'm just used to it being that way. Just a guess though. For the record, I agree: regardless of how the outlet is mounted, bottom should be switched and top should be hot. Just makes more sense that way for the reasons you've described.

Thanks -- very clearly explained. Wouldn't it make more sense to switch the bottom and leave the top powered all the time? Presumably, the switch will control relatively permanent objects like a floor lamp. I like to keep the top receptacle open for plug-in loads, and leave the top hot. I've always wondered why people switch the top, and not the bottom.

Very nice videooo,thanks

very nice connection

Hi Mark thanks so much for a great info. Hey so this outlet could work for under my kitchen sink with the garbage disposal right?

I have a question i have removed a lighting fixture from the kitchen it had two lights working off one switch though i replaced one light with a receptical so i could get constant current though the box in the wall only has two wires white & black no ground two wires only, so is there yet a way to have current running constantly to this receptical or will i have to run another wire from breaker box to the receptical in order to get constant current? The toggle switch is wired with two black wires no neutural white wire is connectedto switch though there are five of them that are all wired together, so is it possible to get constant current maybe even just configuring wires in the switch area?

Hi: This is for new work and is very clear. How about for old work? I have a switch to a Garbage Disposal BUT the Dishwasher goes to the same Outlet under the sink? Help!

Thank you.

How is the white wire Hot? Where is it getting the power from? The pig tail?

How would I wire a ceiling fan off of the switch?

watched your video on the half switch it works but i did something wrong as the whole outlet goes out no prob but i think i messed up somewhere in the wiring

Thank you! I just wired a receptacle/switch in less than 10 minutes!

does the neutral from the service panel attach to both silver nuts on the outlet? You said nuts but it looks like it's only attached to one nut. Thanks

Hi can you help me. If I wanted both outlets to turn on and off. Do not cut the metal tab?

I Like it

Can i switch a single pole switch to a switch and receptacle from a 14-2 wire?

so this is probably obvious but I'm still a little un sure 😟 does that mean the top part of the plug does not have a neutral going to it?

I have a situation I need help with. Do you offer assistance on a unique basis?

Thank you. Prob pretty basic but electricity scares the bageebees out of me. Powertools no; and I lost a finger to them. I was 90% there with the diagrams I've seen but I trust it all better that I've gotten to SEE the real thing, not just colored lines (which don't match my wire colors) on a diagram.

How would you wire a GFI outlet like this?

I have an existing switched outlet with 2 outlets. Do I just need to cut off the brass to make only one of the outlets switchable? Thanks.

The switch box and switched outlet have a red wire in my room. None of the wires were connected.

I'm having to reverse everything because now it's required to face the ground up. :/