This will only work for switches with a filament type light bulb. If the switch has an LED then you must use the copper coloured pin as negative/ground or the LED will not light.

This is a great video. More clear and concise than some others.

Very good. Another video showed a car battery for the power source and a DC battery for the load.

Excellent video, very well explained, I got it working😃

Tnx a lot, very clear how you tell it and show it.

Copper is negative so the switch can light up when it's on not off

Fantastic explanation! Thank you!

Finally, problem solved. I understand now. Thanks bro.

Got me confused. You say copper pin is for the positive in but based on the switch wiring you are then running the load through the light. Diagram shows copper tab as -ve or neutral for operating the light and silver tabs are for input and load.

Thank you very much very helpful!

bad wiring form. red is for positive and black for negative. you have it reversed

That which switch

Thanks for the vid ! Appreciate it.

Thank you. It helped me greatly.

Thank you .. I think all the other videos are for AC took me awhile to figure that out lol

It works with me! Thank you very much. One last question please, Although it works but the red light in the switch didn't work, Do you know why? *NOTE: - I use an adpter like you, so the switch is conecting with 2A 12V - (15A 250V, 20A 125V) was written on the switch

Question . I have a 3 prung toggle switch with a led light . And I’m runing those diy relay box I made which u also get power from . Or Do I run power to the 12v ignition wire ? And the reload to my relay box?

Really great helpful for me this video keep it Up brother thank u so much appriciate much

Are you sure this isn’t backward? Most instructions / diagrams (and KZfaq videos) say to wire the copper wire the ground / negative. Also usually the I / on is at the top (O / off on the bottom ) for safety reasons.

Great videos ! Thx

Where did you get this switch? I was looking all over Aliexpress and they only have 230V variant :(

I thought the brass terminal was used for gnd. The center for power and the for output device

i saw ur previous video list, actually i was thought u are indian, now i knows u from Indonesia, that's why say i was talk ur accent 😬😁

thanks alot simple explained now i can wire my leds lights thanks

Great video!

Very nice video thanks for help

Excellent ....Thank you

So to understand this further. The switch closes the open ground(black) the device when switched on?

Very well explained.. got it 👍 Thnks bro ..

But there are other videos where the copper one is the negative.. So which one is it??

Good video

Kya aap mujhe iska reason bata sakte hain

thanks for your

Thank you very much!!!

Thank you bro But does all 3 pin witch can be connected the same ?

what about a 2 pin illuminated switch?

❤do you need any fuse to the load or switch 🤔

well explained!

Aapka ye circuit lithium ion battery ki charging par work nahi kar rha h nahi battery charge ho rhi h

Can I just short the copper pin with the middle one?

Good video in general but you made a big mistake with the poles. That’s going to confuse people

How will i put this switch on positive line to be a usb charger switch ony motorcycle?

will it work for forward and reverse switch

mine kcd 1 . its same or not

please reply ...AC switch like your switch (220v 15a ) , wire connect same way ?

Great video. Question...I'm new (self taught) to electrical engineering, repair + maintenance of ebikes. I installed a 4-light system on ebike - backlight, high beam (×1) and low beam (×2). I run everything through a 12v/24v power source (bank). Recently, I decided to add rocker switch (×2) to separate high be from low beam. I noticed that the LED indicators on the rockers will sometimes work, sometimes not but the lights will always work. I've looked for shorts, can't find anything. Power source is rated for 12v/24v. I register 28.5v on multimeter when everything is turned on. Could this be the cause why the rocker lights don't work? I've switched out rockers twice....same result. Hope u can help. Great video. /bklyn 👑

Aw come on, 0:50 Pin 3 ["Copper"] says "Neutral", You say "Positive". 1:07 What gives? i'm more confused. switch i have has NO Copper pin. 2 wires needed on one pin, but which one? Shared Positive or Accessory? Now, WHICH is Positive on switch, Really ?

Is this okay for blender??

Sir what about a 220V switch, will it work if I used it in my motorcycle??

Excellent!! Can i use the same wiring for AC240 Thanks

Do you have to have a ground on it

Bhai mic kharab hai kya

You always break the positive, dont you?

Excellent sir

This is wrong the brass is for the neg sir

where can use 3 pin switch, please give example

Your video was out of focus of the camera from beginning to end ! You should look into the matter?

copper is ground not positive

Yea, uhh.. bro, you gotta rewire your whole incubator thingy. That copper tab is DEFINITELY for NEGATIVE!

Very misleading. Copper is -ve

Funny howneveryone else wires the brass tab to negative! btw that is NOT a wiring diagram

Word

Wooow❤️👍❤️👍Wooow❤️👍❤️👍Wooow❤️👍❤️👍Wooow❤️👍❤️👍

saklar memutus arus negatif...

lol bakWardz