HOW2 install Dr. PULLEY roller | Honda SH 300i

HOW2 install Dr. PULLEY roller | Honda SH 300i | FMP-Solid PASSion |

Рет қаралды 30,046

FREAKMOPED Vespa Tuning | FMP - SolidPaSSion |

Күн бұрын

installing dr. pulley in a honda sh300i, very interesting effect! acceleration video 2come, curious how much faster the engine is now
23x18mm rolls, 16 gramm instead of 18,9gr original honda rolls
i ordered
SR2318/6-16 rollers
SP2418-K gliders
--------------------------------------------------------------------------
FOLLOW me on
insta: @FreakMoPed
fb: / freakmoped
--------------------------------------------------------------------------

Пікірлер: 28

@volt8684 Жыл бұрын

Great job why did you round the corners in the variator please

@FreakMoPed8 Жыл бұрын

cause they were sharp

@rezkia.pramudita19 Жыл бұрын

Hello Mr. FMP, have you also ever heard or even tried techpulley fr2 for your scooter?

@FreakMoPed8 Жыл бұрын

no. i dont see much power hidden in cvt, so with just pulleys its already fine

@TonyFaiDaTe Жыл бұрын

hello on Dr. Pulley's website for sh 300 a weight of 18gr is recommended, why did you put on 16? Have you also found benefits such as maximum speed? Thanks

@FreakMoPed8 Жыл бұрын

massive plus at lower revs, topspeed the same. anyways limited due to my seize and weight. dont think i saw 18 as recommendation back then (6y)

@stephenportelli9653 5 жыл бұрын

Can you tell me the outside diameter of the variator fan of the SH 300i please?

@FreakMoPed8 5 жыл бұрын

Sry, no idea.

@Alph92 5 жыл бұрын

How much Nm do I need to tighten the variator assembly and the clutch assembly? unfotunately I'll have to use a lever with pins to hold the variator and unscrew the nut manually. do you by any chance know the spec of a new belt so I know whether i have to change the belt aswell? I am planning to put in 17g rollers which I already bought.

@FreakMoPed8 5 жыл бұрын

83nm and screw lock

@FreakMoPed8 5 жыл бұрын

belt new 26,5 / limit is 25,5mm / butbits good for 15-20.000km they say

@Alph92 5 жыл бұрын

mista FreakMoPed Ok that Sounds really good. I was a bit unsure because the description of the Dr pulley Hit clutch says that installing softer pillow springs will increase belt wear a lot but since I don't ride all that much even changing the belt once every 6000 - 8000 km would still be Ok.

@FreakMoPed8 5 жыл бұрын

not experienced with other clutches, fan of the original hardware :)

@fazer12779 6 жыл бұрын

Do Dr Pulley rollers perform better than Honda oem rollers?

@FreakMoPed8 6 жыл бұрын

Pulls a lot better, more agressiv. Makes realky fun to ride

@Thanasis.K. 6 жыл бұрын

HI why i must round the corners when i install the dr pulley rollers?

@FreakMoPed8 6 жыл бұрын

Edge od the vario lid u mean? Cause its sharp. All sharp edges that come. In contact with moving parts should be rounded.

@Thanasis.K. 6 жыл бұрын

thank you

@ballkeeper6662 2 жыл бұрын

i bought a s/hand sh300 ,the centre 2 pins in mine there only 1 the right side pin in place can this give problems

@FreakMoPed8 2 жыл бұрын

no not really

@ballkeeper6662 2 жыл бұрын

@@FreakMoPed8 thought it may mess with the bell housing

@AndiNRG 2 жыл бұрын

Hey, mein SH 300 hat dieses typische Ruckeln bei niedriger Drehzahl. Woran liegt das, bzw wie kann man das am besten beheben? Liebe Grüße aus Bayern.

@FreakMoPed8 2 жыл бұрын

gib ihm mal vollgas zum vario entstauben. lufi reinigen auch gut. ggf k&n damit werden die laswechsel smoother

@AndiNRG 2 жыл бұрын

@@FreakMoPed8 super Danke, werde ich gleich umsetzen.🤝👍

@borreltjuh83 3 жыл бұрын

What is the weight of the dr pulley rollers installed? Any other mods?

@FreakMoPed8 3 жыл бұрын

23x18mm rolls, 16 gramm instead of 18,9gr original honda rolls with pulley glider. . see the acceleration videos. Added k&n tried forcemaster ended up with dynojet pcfc