How to make a High Voltage Transformer

Рет қаралды 249,140

6 жыл бұрын

In this video I show how to make a multi section high voltage transformer, ferrite core from old TV and 32 gauge copper wire.
More information in the instructables:
www.instructables.com/id/High-...
Despite the fact that my English is almost perfect, maybe you could notice a small Eastern European accent, it's because I'm Russian, and answering the question "why don't you make videos in both languages?" I actually do, and my Russian channel is here - / shhitov
(the videos are the same, so for English-speaking viewers it makes no sense to subscribe)
Music:
Moving Over - Silent Partner

Пікірлер: 117

@tefatronix 6 жыл бұрын

Very nice job! The finished transformer looks great and works great too :)

@nikolaishriver7922 6 жыл бұрын

Really cool, im going to try this, I dont have a 3D printer, but i have a lathe I will just turn a similar piece and mill out the slots in the plastic. I’m thinking of just using a simple 40amp DC PWM speed controller to control the frequency for now. It doesn’t have to be super precise. I have a few projects I need some REALLY high voltage for. Thank you for this video and construction techniques

@johneygd 6 жыл бұрын

These high voltage transformers are like magic in how it can turn low voltage into high voltage,really impresses me,

@noelandrew3600 6 жыл бұрын

I don't have access to a 3d printer but im an engineer with lathe access so im going to make a bobbin based on your design from solid stock nylon. really like your design and have a load of flybacks from old tvs that i have stripped but as with you, i need HV AC not DC for many of my projects so your design is mint.

@Biokemist-o3k 2 жыл бұрын

Noel, Did you ever make any of these cores from your lathe?

@neoplasmax 5 жыл бұрын

I think this video is great.. I just wish I could totally understand you... lol.. I need to listen to a few more of your vids or watch this one over and over and eventually I'll hear ya..

@tf3confirmedbuthv54 6 жыл бұрын

Amazing video! Subbed!

@peterlorne7077 6 жыл бұрын

Nice video! ! Can you please make a video on Arduino driver you use. Thums up for you! ! / Peter

@callofdutymobilegameplayra8140 6 жыл бұрын

nice job man

@hassaneinshaban6077 6 жыл бұрын

is there transformer can be connected to function generator and step up the voltage to 1 kv at frequency 1khz??

@NITESCIENTIST 5 жыл бұрын

I too flip off my projects when they're not cooperating.

@hubb8049 3 жыл бұрын

@Biff Danielson I just curl myself like a fetus and begin to cry

@gyojoonpark9974 5 жыл бұрын

How did you make the herz control? how high can herz be, up to 10-20mhz?

@sunitaplasticworks7290 6 жыл бұрын

Sir I needed your help to solve my problem regarding this kind of coils

@SaltGrains_Fready 6 жыл бұрын

Use No 40 wire with 11% more space between core and base of winding. Reduce Space between individual windings by 35% and you will get 25% more sets of windings and 60% more turns onto the configuration. This will provide output of more voltage with less driver current.

@diy-or-die5700 5 жыл бұрын

Adding 60% more wire whilst reducing insulative material between coils is a terrible idea. This works great if using a diode stack (one in between each coil) for DC output. The problem is HF AC eats/degrades insulation over time. Many 3d printing materials also suffer large losses and heat considerably from HF AC.

@DeepSingh-wo1tt 2 жыл бұрын

Hello Sir, I would like to request how to calculate for these windings? do you have any link to its calculations

@BushCampingTools 4 жыл бұрын

Great I'm subbing!

@KashmirPL 5 жыл бұрын

please show how to build driver to control frequency

@johnruscigno5738 5 жыл бұрын

You made a fly back transformer, they're awesome for generating arcs.

@RickGreenPhoto 6 жыл бұрын

I like it! You made a great video! I am kicking myself now for throwing my old laser power supply transformer in the trash :)

@nanoindus 5 жыл бұрын

nice one! I have a question. How do take the wire from one section to another section? I see there are slots accross the section. the last turn of a section has higher voltage than the first turn of the section. When we take the last turn of one section to first turn / layer of the next section, there will be large voltage differences. Does it not cause arcing through copper wire insulation?

@diy-or-die5700 5 жыл бұрын

This is a key concern when winding such transformers. You have two options. The first being to estimate/roughly calculate the peak voltage potential between each pancake coil/spacing and then submerse the transformer in oil and/or add a sheath onto the transfer wire heading into the next section. The second option (more ideal) is to have a hole and "tube" leading to the BOTTOM of every division allowing the HT wire to start at the bottom of each division thus greatly reducing arc over and wire to wire potential.

@dickesf8525 6 жыл бұрын

Hey, yeah, pls a Video on the Circuit :D

@sahibbhullar9838 5 жыл бұрын

Is this work on mosfit z44 woth 1k ohm regsitance

@sasabl1 6 жыл бұрын

Great video and great device. The link you provided to Instructables leads to copper plating and not instructable for this device. Cheers

@ihsanbu 5 жыл бұрын

nice guiding

@mohammadhashemi1771 3 жыл бұрын

hi Nice work I'm working on a project that needs a pulsing circuit can you help?

@worroSfOretsevraH 3 жыл бұрын

What is the purpose of multiple slots on the high voltage winding? Can you share a link where I can read more about the theory? Thanks.

@BrunoSantos-lm1pz 4 ай бұрын

It makes it so that in 1 slot the voltage between the winding with the lowest potentential and the highest one doesnt get too high and arc. It divides the high voltage into multiple lower voltage parts.

@vikbec8329 3 жыл бұрын

Привет,хорошее видео,меня интересует какую программу ты взял для анимации,3д конечно бюджетную спасибо заранее

@sahidamardhi 2 ай бұрын

does the direction winding relatif to the primary matter in flyback transformer?

@markopopoland 4 жыл бұрын

Hello can You help me ? I want to make HV transformer for ozone generator. I have Chinaise ozone plates with parameters 5kV 80W can You give me details for wires diameters etc, trigger ?

@Reilly18 2 жыл бұрын

where can i download the insulator?

@gsadashiva529 6 жыл бұрын

sir what is the black material using outside of coil . what is that name and what is the use?

@diecksl 5 жыл бұрын

Its ferrite. Its used instead of an iron core like in a "classic" transformer. It works best at high frequencies (in kHz to Mhz range), so you always need a driver circuit (ZVS, royer) to power a ferrite core transformer.

@technomindsindia 6 жыл бұрын

thanks man

@christophercridlebaugh8965 4 жыл бұрын

Can you post the stl file so I can print this bobbin please sir

@elektrocat8681 6 жыл бұрын

Can you upload the stl file?

@andrewmoore3377 4 жыл бұрын

whats the model link?

@sanek51175 6 жыл бұрын

во Кот заряжается,красава

@velipekkajutila9451 6 жыл бұрын

can you link the file for the 3D printer? Maybe with the thicker walls

@breezetix Жыл бұрын

design your own

@theactingkings701 5 жыл бұрын

Please tell what is the object shown in time 30:00

@h-primehiro1044 4 жыл бұрын

Hello brothers what is the music name us it in this video

@randomstuff23453 6 жыл бұрын

спасибо

@ItaloLima 6 жыл бұрын

Cool !!

@NAANsoft 4 жыл бұрын

"A good idea is to use xxx - but I don't have it" ... LOL

@theq4602 5 жыл бұрын

hello, I am looking to brute force myself to high voltages with no driving circuits. I am looking to re-wind a MOT transformer for 30000 volts at 30mA (900W). Will 32 gauge wire work? I estimated I will need 32000 turns. I will rectify the AC to DC and use a Variac for power control. I want to re-use my primary coil. I do not like using driving circuits and such and need the ability to swap between negative and positive output.

@paulbyerlee2529 3 жыл бұрын

It would be easier to use a voltage multiplier to get to that kind of voltage. Start out with 3000v and do 10 or 11 stages. The down side is you won't have that level of current. 30ma could potentially be lethal. I'd try to keep it under 2.5ma or even get it in the uA range. If you just want impressive arcs try a Marx generator.

@theq4602 3 жыл бұрын

@@paulbyerlee2529 I wouldn't get the current I want

@linusmadrone 2 жыл бұрын

Cool Thanks.

@electronresonator8882 6 жыл бұрын

2:25 that is unexpected

@MrMedico33ER 6 жыл бұрын

he shows to be a very unpolite person (thums down)

@moneyaccount9775 6 жыл бұрын

I unsubscribed

@MrMedico33ER 6 жыл бұрын

well done bro ;-)

@vapenation7061 6 жыл бұрын

fucking pussies

@american0153 4 жыл бұрын

MrMedico33 snowflake

@clovisoliveira1794 6 жыл бұрын

você me mostrou o dedo do meio 2:25

@alexonuminyad9244 4 жыл бұрын

Hi, sir how this work

@trenthighvoltage 2 жыл бұрын

"there are a few bubbles inside" there's also a lot of air still inside the windings. which will cause internal arcing almost instantly.

@armandinamontanez9545 2 жыл бұрын

The images in the finish of you video it's so Bad Bot you proyect it's so greate..

@RubbinRobbin 4 жыл бұрын

can this be used for DC high voltage?

@h-primehiro1044 4 жыл бұрын

No if you use DC no magnetic field no arc You can use AC Use the AC POWER SUPPLY Or you can use DC by multi mosfet transistor

@AsimKumarMahakul 2 жыл бұрын

you have to multiple High voltage diodes, between sections or else if you are planning below 15kv then one 15kv diode is enough. But here dc means one direction not ripple free, but that works for every physics research needs from xray to ion beam.

@pauldery7875 Жыл бұрын

Nice work, could you do a video on the arduino driver, thank you. I am in USA

@moonzip0147 4 жыл бұрын

Liquide name datile plz

@mihylcecastillo1092 6 жыл бұрын

Hey brother that winding is one direction????????????

@timothyegoroff8333 5 жыл бұрын

yes.

@DigitalMaster_23 Жыл бұрын

How to get thin copper please tell me😢😢😢😢😢😢😢😢😢😢

@arkhilious 5 жыл бұрын

900th like!

@luizissaox 6 жыл бұрын

2:25 for you

@Lust4Shorts 6 жыл бұрын

Plz make

@woodrowcook7979 5 жыл бұрын

Nice pink knife.

@psun256 4 жыл бұрын

Wouldn't oil work fine instead of resin?

@curtisburdick2849 4 жыл бұрын

yes oil is great insulator and cools the transformer as well just got let it touch any thing giving off electricity. Is seen pwople cover these transformer in hot glue thebun a glass jar of oil

@basiljaworski6720 6 жыл бұрын

Класно!!!

@Doctorlockpick 4 ай бұрын

Do you have an email so I can contact you?

@chuonglam9929 6 жыл бұрын

What is the liquid at 2:20?

@mehmetuguryldrm5865 5 жыл бұрын

epoxy resin

@chuonglam9929 5 жыл бұрын

Thank you.

@TauCu 6 жыл бұрын

Hey, You will burn out your transformer like that, I'd recommend putting it in a transformer oil bath. Then you can drive it even harder. If you look closely your transformer is turning blue when its on (arcing across)

@elianedapenha1317 4 жыл бұрын

2:25

@null-xv3eq 6 жыл бұрын

Flyback transformer

@MOfrhr 5 жыл бұрын

Does it work at 350 000 hz ?

@diy-or-die5700 5 жыл бұрын

It depends on the transformer core specs. If the core can handle 350Khz, then it sure would (coil numbers/layers differ vastly with different frequencies however).

@MOfrhr 5 жыл бұрын

DIY-OR-DIE thanks for your reply.

@vardfriki7274 2 жыл бұрын

MAGIC SMOKE. YEY!

@scienceinnovativebrain 3 жыл бұрын

Epoxy name

@virgilius1979 6 жыл бұрын

Your project is great, but most people don't have 3d printer and are not familiar with arduino, so not very practical :)

@nautitard 5 жыл бұрын

Well most people have heard of Arduino and can possibly get or use a 3D-printer. If you don't have the tools, then you can't expect to do everything you want to. Not saying it's necessary for this kind of project, but in many cases you can't blame anyone with the right tools for you not having the right tools x)

@HolahkuTaigiTWFormosanDiplomat 5 жыл бұрын

@Electronic4081 5 жыл бұрын

Bogdan Rotaru There are a lot of 3D printer kits available now for really cheap. They are easy to assemble and use with enough research on them. I got my first one when I was 15 years old for $200 and it was easy enough to assemble.

@mareksvrcina5279 5 жыл бұрын

Are you serious? I think using arduino would be easier for someone who don’t have much experience with building circuits. The case can be made from any other material. And don’t forget that you can get those cheap zvs drivers on eBay. People say they work well.

@Zeddify 2 жыл бұрын

Just use the flyback transformer itself

@rickmoreberry1133 5 жыл бұрын

Sorry I can't undesirable russian can you speak English please 😃😂😁😀😅😆😆😆👍👍👍👌👌👏👏👏👏

@konstantineendeladze9029 5 жыл бұрын

my name is also konstantine

@Tezcax 5 жыл бұрын

I can't really understand what is being said here

@mihylcecastillo1092 6 жыл бұрын

:):):)

@rohitghoshclass-ixdrollno-4268 3 жыл бұрын

2:26😂😂😂😂

@sanek51175 6 жыл бұрын

некогда не показуй фак,и остальные гадости,будь лучше и выше чем они

@kamisama9715 2 жыл бұрын

This dude sounds like he has marbles in his mouth

@edersonsimples6782 3 жыл бұрын

🍌

@basiljaworski6720 6 жыл бұрын

Звідки ти? Чути акцент снг)))

@barlawsitanggang8582 6 жыл бұрын

👎👎👎👎👎👎

@siddheshbhor3576 6 жыл бұрын

Learn to speak English well first

@MrMedico33ER 6 жыл бұрын

yes, but after learning the education, just see how much he can do without pointing the middle finger .. he should stick it in his own ass

@anthonypuettmann947 6 жыл бұрын

You guys are so rude

@jamesnichols7583 6 жыл бұрын

Trolls should go to hell

@paulbyerlee2529 3 жыл бұрын

His English is better than my Russian.

@dancoz5477 2 жыл бұрын

@@paulbyerlee2529 Comments on his ability to master English is typical from language illiterates and/or snobs. Poor people. I think his English is perfect.