Husqvarna axle seal.

Рет қаралды 10,377

C & L Lawn Care

3 жыл бұрын

Пікірлер: 30

@Lovinflyindrones2022 3 жыл бұрын

I hope u don’t quit making videos!!! I really enjoy and look forward to your next video. You’re a natural on camera

@clsmallenginerepair3814 3 жыл бұрын

Thanks man,, I wish I could make more videos. Sometimes its like, its all been done..lol I'm gonna be doin an end of year video soon. And probably a 1 year review on the Bradley mower.. Thanks for the comment and support 👍

@Lovinflyindrones2022 3 жыл бұрын

@@clsmallenginerepair3814 anytime. I like trying to support all small engine repair especially the smaller channels as well as the bigger ones. I’d go ahead and do a video on whatever you can. I like seeing maybe a different take on how to fix it or a better way. Just saying. Thanks again

@oberurselts Жыл бұрын

I had the same problem with an old Craftsman a few years ago. The rear wheels refused to come off. It ended by me doing something really stupid! I tried to knock them off with a small block of wood. The end result was the axles became disengaged from the trans. I went and purchased a new Husqvarna 46" Lawn Tractor. I found out that the axles should be lubed at least once a year, normally at the beginning of the season, with anti-seize. Yelp! That's right. Anti-Seize. If you don't do this, the wheels will seize up on the axle. Even new lawn tractors only come with a thin layer of oil on the axles. This is just not sufficient!

@TheRustyRooster 3 жыл бұрын

Gee wiz what a pain that was to watch. Glad you were able to get that darn wheel off. Hope ya got paid extra for all that hard work.

@clsmallenginerepair3814 3 жыл бұрын

Sometimes your the windshield, sometimes your the bug..lol Thanks for the comment.

@butler386 3 жыл бұрын

Oh man that was horrible. I have an old Murray that I probably will have the same difficulty. Great endurance for sure. Thanks for the video. Love it that your grand daughter is interested in what you are doing.

@clsmallenginerepair3814 3 жыл бұрын

Thanks,, I'm starting a votech class for my 3 grandsons. There are two 11 and 1 that's 6. Home school thing.. but yeah, my granddaughter would rather do mower repair than home economics for sure..lol

@butler386 3 жыл бұрын

@@clsmallenginerepair3814 Fabulous. Get an old engine and help them take it apart. Maybe each with their own engine. They can clean it all up and mount it on a board for their room.

@clsmallenginerepair3814 3 жыл бұрын

@@butler386 good idea. I'm gonna start em on basics. Mower components, what parts goes in each Components . Just like a real class. Hopefully I can show em rebuild an engine on the channel. Might be awhile. But atleast them doing repairs on the channel would be cool.

@noahlail4018 3 жыл бұрын

That’s one of the many reasons I really don’t like that type of axle. Much prefer to just take off four bolts

@diecart2 2 жыл бұрын

When you had it so hot did you try quenching it and use the air hammer . Watch Taryl

@clsmallenginerepair3814 2 жыл бұрын

Ive seen taryl do that..

@larrygutman9785 2 жыл бұрын

at 15:10 when you ran your finger through that groove - that groove has very sharp edges and you could get a nasty cut

@clsmallenginerepair3814 2 жыл бұрын

Theres very few days go by that i dont bleed in something..lol Thanx for the concern.

@joannlupinacci8444 Жыл бұрын

We replaced 2 real axle seals on our Husqvarna 46in. Riding Lawn Tractor.. and they keep leaking..What could be the problem? Thank you for taking the time to answer.

@Preacher7633 Жыл бұрын

I'm guessing it's a tufftorq k46 transmission. Gotta clean the shaft really well. Could be u hav something internally wrong, causing excessive pressure, or a Vent tube clogged up, not breathing.( common) If u don't put tape over the keyway cutout, it can cut the seal when u slide the new seal down the shaft. Or over filled..

@Preacher7633 Жыл бұрын

@joannlupinacci8444 Жыл бұрын

@@Preacher7633Thank you...

@jackschiffer9855 3 жыл бұрын

You should wear eye protection

@clsmallenginerepair3814 3 жыл бұрын

True

@stevanrose7439 2 жыл бұрын

Don’t beat on it to hard or you will brake the trans axle housing. If it’s like mine it’s plastic. 😡

@joannlupinacci8444 2 жыл бұрын

My husband wants to know if there is a place to put the oil for the rear axle seals? The right side blew out and it started leaking, he replaced the seal already..He has a Husqvarna YTA 22V46... Can you help? Thank you, JoAnn

@Preacher7633 2 жыл бұрын

If its a k46 trans, should be a black cap under cooling fan, carefully take cap off and add, about 1.5 inches below top,, do not fill to the top, half way up the magnet is good..

@joannlupinacci8444 2 жыл бұрын

@@Preacher7633 thank you!

@joannlupinacci8444 2 жыл бұрын

@@Preacher7633 now my husband wants to know what type of oil should you use for the rear seals? Thank you...

@jewermank8536 10 ай бұрын

I'm in the same boat. I think you gotta drop the transmission and add fluid from the top

@AStanton1966 9 ай бұрын

I know the post is old. You could use any synthetic 20w-50 oil. Personally, I put 5w-50 in mine when I swapped out the oil at 156 hours. By the way, the dealer will tell you that these trannies are sealed and that you shouldn't monkey with them. @@joannlupinacci8444