A whole lot of components that I'm not used to I start my new job doing service calls next week I've been doing new construction for the past 8 years I like your content easy to follow and thank you for doing them for us new Jack's doing service calls
@TaddyDigest Жыл бұрын
Good luck my friend wishing you great success Thank you for watching
@takethe101totarzana4 Жыл бұрын
The Dumb and Dumber reference was awesome, Lloyd Christmas is somewhere smiling. Thanks for posting Tad, solid video.
@rolytech2129 ай бұрын
Before taken the inducer motor out I would loosen the burner manifold out. A lot easier
@thaison7739 ай бұрын
Thanks for taking the time to make the video. I would like to know the size of that gas valve fitting to check for gas pressure with the manometer or if you can share a link of where to buy it. Thank you
@ikecrook14507 ай бұрын
Your menometer comes with the fittings
@jon3862 Жыл бұрын
You are best of the best 👌 👍 HI from GOLSTAR healing and cooling
@emac1111 Жыл бұрын
Great as always. Everything is useful in this video. Go on Tad👍Your subscriber from Azerbaijan
@TaddyDigest Жыл бұрын
Awesome, thank you!
@roqueherrera8471 Жыл бұрын
TAD U ARE THE BEST….. I LOVE YOUR VIDEOS . I going from install to tech and all this is GOLD to me.
@TaddyDigest Жыл бұрын
You are welcome my friend
@ebuzek364810 ай бұрын
never adjust a used belt. always install a new belt and then adjust if needed. put a spare or two in a plastic bag.
@ikecrook14507 ай бұрын
I agree then you get the new one you have to re adjust it again
@fazesenso2864 Жыл бұрын
I’m in my 2nd semester of HVac school and ur videos are really good for learning new things
@TaddyDigest Жыл бұрын
Glad you like them!
@user-ql2bz8on7m2 ай бұрын
It was an awesome video thank you
@elmerramirez1215 Жыл бұрын
Good video man, I’m starting as comercial pm technician and really looking forward to moving up
@TaddyDigest Жыл бұрын
You can do it!
@Eddy63 Жыл бұрын
Good info Tad ... Thx for posting ...
@hoppychulo1015 Жыл бұрын
Great video
@yodamanrulz176 Жыл бұрын
Thank you Tod good information all around. However, being new to HVAC, I find it disconcerting when the teacher uses their elbows/fingers to point at something of importance. Please strive to be super clear by using a probe tip or chopstick to point and maintain the point for three or four seconds for a screenshot reference. Thank you.
@TaddyDigest Жыл бұрын
Great point
@miguelrojas3394 Жыл бұрын
I really like the videos the way you explained and thanks for your hard work.
@TaddyDigest Жыл бұрын
My pleasure!
@steveomac5001 Жыл бұрын
It’s looks exactly like a carrier rtu but it has yorks shitty controller. Crazy
@ikecrook14507 ай бұрын
You can't go off the 24 volt to the gas valve I have had them read 24 but had bad common on board if you have analog volt meter it will read 0
@oscarestrada5509 Жыл бұрын
Great video bro
@TaddyDigest Жыл бұрын
Thank You 😊
@migueldominguez43119 ай бұрын
Great video ! I have a issue with a gas comercial heather that is used in drive tru canopy ! And is not turn on What could b the issue The valve or the main gas ?
@alexibonnet2634 Жыл бұрын
Good video, thank you
@TaddyDigest Жыл бұрын
You're welcome
@garypoplin459910 ай бұрын
Do you have a video on how to clock the meter on a unit like this?
@TaddyDigest10 ай бұрын
No sir but I can make one
@imbobbymuddah2 ай бұрын
Can you use Teflon instead of thread sealant
@antonioquatela43646 ай бұрын
Hello. great content. I Have a question … have you ever experienced a commercial customer call you with a complaint of natural gas odor inside a store? I’m checking these units up and down but am almost out of theories. Is there a premature opening of the gas valve or maybe an induction motor with a leak somewhere? Pretty windy on the roof maybe it needs a exhaust extension brought up higher.
@TaddyDigest6 ай бұрын
could be a bad board or something like that where its sending power to gas valve and not igniting. or regulator vent is leaking
@hectorgonzalez8185 Жыл бұрын
Good video
@TaddyDigest Жыл бұрын
Thanks Hector I have some guides I want To send you Please send me an email at tadfuller1@gmail.com
@aarongray503 Жыл бұрын
Man that was a wealth of knowledge!! Thanks tad! What size of manometer fittings do you typically use? I'm in commercial hvac in Texas but still green.
@TaddyDigest Жыл бұрын
Hey Aaron send me an email thank you so much for joining and being a member tadfuller1@gmail.com
@TaddyDigest Жыл бұрын
Glad I could help
@ikecrook14507 ай бұрын
They are all standard simple barbed fitting works should come with manometer
@glennlockwood7608 Жыл бұрын
Nice video. How did you manage to have a replacement valve on hand?
@TaddyDigest Жыл бұрын
I did not I ordered it it came in in 2 days I am an hour and a 1/2 from Nashville to an hour 2 hours from Memphis One hour from Jackson I have suppliers all over near me
@brandoncorrea511 Жыл бұрын
Keep doing these vids. I like it 👍
@TaddyDigest Жыл бұрын
Thanks, will do!
@stevencovington1776 Жыл бұрын
Hey great video, but did have one question, you normally check your sensor by ohms reading and not continuity?
@TaddyDigest Жыл бұрын
Normally I check the resistance reading Continuity is also a good check
@srobeck77 Жыл бұрын
Its generally going to be an ohms reading. Continuity is generally for broken wires. Either way, its the same mode on your meter to look for low ohms or O.L.
@ikecrook14507 ай бұрын
It will work the same way I use continuity
@stevencovington1776 Жыл бұрын
which membership is with the private videos and support?
@TaddyDigest Жыл бұрын
level 3 😁
@juliocastillo19887 ай бұрын
👍👍
@roqueherrera8471 Жыл бұрын
I would hate to ask but do u have any Carrier/Trane/Rheem unit trouble shoot
@TaddyDigest Жыл бұрын
I'm not sure if I do or not I think I do but if I don't I'll have some soon
@paulrozinski1488 Жыл бұрын
Why all the rust on the gas pipes and disconnect switches ?? What area of the US is this ??
@TaddyDigest Жыл бұрын
Tennessee near Nashville
@srobeck77 Жыл бұрын
Pipes rust everywhere doesnt matter the location. Even indoors. In salty air, close by oceans, is where metal will rust much faster.
@marwinbrown50895 ай бұрын
Awesome video, giveaway
@Ray-wr2wr7 ай бұрын
hi what are they symptoms when dirty burners ?
@TaddyDigest7 ай бұрын
flame will not spread across burners if dirty
@Ray-wr2wr7 ай бұрын
@@TaddyDigest thanks
@Ray-wr2wr7 ай бұрын
@@TaddyDigest what's causing mini explosions /bang on commercial RTU ? gas furnace
@sergioramirez9025 Жыл бұрын
Hey tad quick question how did you know that sensor was supposed to be 10k ohm? I haven't diagnosed that sensor before but on the ODA and SAT MAT sensors RTA sensors etc how do you check those? Is that with a 10 k ohm chart? And has to match the same ambient temp outside???
@TaddyDigest Жыл бұрын
Hey send me an email I have some guides for you tadfuller1@gmail.com
@TaddyDigest Жыл бұрын
yes I use a chart I can send you what I have
@sergioramirez9025 Жыл бұрын
@@TaddyDigest just did👍
@TaddyDigest Жыл бұрын
Awesome
@abdullah_q8171 Жыл бұрын
Microchannel is Cheap coil .
@srobeck77 Жыл бұрын
I think they actually cost more and are have better efficiency. But on the other hand, they break easier and are harder to repair. We require them to have hail guards on the rooftops units in our facility.
@srobeck77 Жыл бұрын
Your pipe doping skills are lacking here. First, you gotta clean the old threads with a wire brush. Next, apply a thin coat (more is not better). Last, you have to make sure to not get any pipe dope on the end of the pipe (you definitely got a big gob on the end of the pipe) so that it doesn't go into the system and cause problems. A final recommendation is that cogged belts are superior to those straight, standard belts.
@TaddyDigest Жыл бұрын
thanks for watching and for the great tips 😀 👍
@srobeck77 Жыл бұрын
@@TaddyDigest I hope that didnt come as me being a jerk. Its very hard to strike a balance between criticism and not coming off as being insulting or disrespectful. (The same problem happens with text messages too Ive found.) I did very much enjoy your video here and look forward to more.
@TaddyDigest Жыл бұрын
Friends look out for each other friends say something when others say nothing. It's better to say something Iron sharpening Iron Thanks brother.
@mahabubulalamshusom63279 ай бұрын
Big fan of your videos@Taddy_Digest
@TaddyDigest9 ай бұрын
Thank you brother. I really appreciate your support and I appreciate you watch the videos