And I always wondered what those extra holes were for in the pulley hub. Your video is an great tutorial. Thanks.
@EminHVAC10 жыл бұрын
Your welcome. Sorry I kept on saying nuts instead of bolts or set screws. I should explained better. Lol thanks for watching brother.
@mastertech.81hvacr86 жыл бұрын
Sweet work Dude, I do the same type of stuff down around the Atlantic City area. This is exactly what I like to watch. Keep up the great work Thanks L.U. 322
@bayouairsolutionsinc10 жыл бұрын
You can tell you know what you are doing!!! Nice video. Keep them coming. Looking forward to part 2.
@EminHVAC10 жыл бұрын
Thanks you brother. I'm still learning everyday. Thanks for watching
@manuelponce37155 жыл бұрын
Great Video, you make Commercial HVAC look fun. I hope you make more Videos.
@jhhvacplumbing194410 жыл бұрын
Cool stuff emin , keep up the good work.
@PaulHVAC17 жыл бұрын
Very good installation and teaching !!
@CARONACHRIS071110 жыл бұрын
Im enjoying these commercial vids and your entire channel brother
@EminHVAC10 жыл бұрын
Thanks brother. I hope I explained proper enough to understand what's going there. I'll have part 2 tomorrow.
@RobHVAC10 жыл бұрын
Nice work. Looking forward to the next video.
@EminHVAC10 жыл бұрын
ThankThanks brother. Sorry I couldn't explain better with the locking screws. I kept on saying nuts instead of bolts. Lol. Part 2 is uploaded
@rakselectric73907 жыл бұрын
cool job man awesome videos
@mazzmari10 жыл бұрын
Sta minchia! Lol good job, I usually cut or torch out those bearings when they don't come out with pullers.
@EminHVAC10 жыл бұрын
Yeah I've done that aswell. Thanks for watching buddy
@thomastrang48157 жыл бұрын
"she.....is......moving." Thank you for sharing!
@dennisqwertyuiop10 жыл бұрын
nice work like I used too do before retired
@EminHVAC10 жыл бұрын
Thanks Dennis. Thanks for watching.
@othoni9 жыл бұрын
Hey Emin. What brand/model was that puller? Im in the market to buy one of that size
@NOEISY16 жыл бұрын
thank you for the video
@jimmyordiz10652 жыл бұрын
nice info bro.thnx a lot
@jonathanraul40864 жыл бұрын
Nice video ty
@rc92665 жыл бұрын
Why is the shaft tapered at the panel? is there something missing in that grove?
@goonzsquad12 жыл бұрын
Yo I have a question, if I wanna replace a bearing, how do you measure the old one? Or do you just get the middle and serial of the unit and give it to your supplier ?
@fasttimestr8 ай бұрын
It's a taper lock bushing
@jesusmercado69477 жыл бұрын
dam that thing is massive
@rodgraff17824 жыл бұрын
If you clean polish, and lube the shaft first, you wouldn’t have to work so hard to get the bearing off. Also, if there was any wear or galling on the shaft where the bearing seats, the shaft should have been replaced.
@albahroe124 жыл бұрын
What’s the part number for the big puller
@SteveSam6610 жыл бұрын
Emin, Good Job. Ive had those types of bearings seize and pretty much weld itself to the shaft. The only way to get it off was to use lots of heat and cut it off.
@EminHVAC10 жыл бұрын
Yes. That's the way it's done. Thanks for watching brother
@EminHVAC10 жыл бұрын
hey guys my editing sucks. im still learning how to use that program. i don't know why i kept on sayin nuts instead of bolts. lol
@chrism72758 жыл бұрын
+Emin HVAC lol i ben watching alot of ur videos u do call bolts nuts alot but i do the exact same thing even when i know its a bolt, bolts an nuts go hand in hand
@DAVE430727 жыл бұрын
Where are you,Emin?
@jimdavidson52085 жыл бұрын
"Lack of maintenance momma, lack of maintenance".
@smitty17153 жыл бұрын
R.I.P BRO
@mshane865 жыл бұрын
2:02 Deez nuts! Ha ha, got 'em!!
@techsavkyle76097 жыл бұрын
And flywheel instead of pulley
@neiladrianabne54365 жыл бұрын
correct it is flywheel, pulley is in the motor, blower side is the flywheel now you learn
@jimdavidson52085 жыл бұрын
Or you could go get the PROPER PART so the next guy isn't rigging it like you and the blind helper did.
@stevenlavimoniere10 жыл бұрын
good job ????why do you wear gloves i can not figure out why for the life of me .
@EminHVAC10 жыл бұрын
Hahah. Cause Steve lav told me tooo. Thanks for the comment steve.
@BillyKnoth10 жыл бұрын
Nice Job as usual !!! I miss working on the big stuff!!!
@stevenlavimoniere10 жыл бұрын
fuck the big stuff . better working in houses .more money to be made and faster
@BillyKnoth10 жыл бұрын
I agree man... I found the big stuff fun... But I love the smaller stuff...lol...
@EminHVAC10 жыл бұрын
Yeah the big jobs you have to wait for your money. Steve like you said in the commercial field you have to watch your tools. I had 2 drills stolen from me
@danilorosich7 жыл бұрын
Please, shake the camera some more....
@jeremiasfe11 Жыл бұрын
vamons
@thesco415102 жыл бұрын
Someone greased the shit outta those bearing
@dougshakell80034 жыл бұрын
Rookie or dumb as duck lol clean shafts first. Then u only need to break it loose and will slide off. Also have cut or smash casting then puller fits onto bearing itself. I have done hundreds of these . Easy work made look difficult for sure