Glad there are people like you on KZfaq. You make trades easier to learn and perform.

You are spot on about not using impact wrenches for stuff like that. Way to go, and thanks for doing it the right way.

It's not often you get to see a master at work. Awesome video, thanks. You saved me a lot of time.

Emin, it's a pleasure to watch you tame those big beasts. Thanks for all the tips in the video.

Always enjoy watching your videos, we have the same tower BAC, lol, my belts are getting loud too, waiting on $$ to be approved, have to do same thing. You the man bro.

Great Workmanship !

You have a excellent training skill that your young helpers enjoy learning from.

Thanks for this video. It answered my question about how to separate the hub and pulley right off. Awesome.

Good video Emin. From the looks of how loose those old belts were... that tower was probably screaming. Nice and quiet now..The residents of our fine city, thank you kindly.

i learned a lot from your videos ! keepup the good job

must be a trip going to different buildings, with different hvac setups. with every job you probably learn something new. subscribed my man keep up the good work.

Thank you Emin for share your knowledge.

👍 This is the same pulley/hub setup, used on my Vermeer tree chipper cutting drum. Been searching the web for hours about guidance on how to separate the two. The hub and pulley are rusted fast, stripped out the threads trying to separate the two. I will Helicoil then try again, but with heat this time. Soaking with penetrating oil for two days was no help.

I enjoyed watching The repair

Great video Emin!

Nice work guys!

Great video Emin.

Muchas, muchas, muchas gracias. Los ingenieros de un laboratorio te agradecen enormemente. Estabamos bien weyes, jejeje. Thank you very very very much. The engineers of this lab are very gratefull, we sucked hehehe.

Que las Martin how are you . I live in Florida’ I went to school for Comercial HVAC . You did A good Trabajo .

Trying to become a millwright the channel is very helpful thanks

You made it look easy, great video my bro.

Great vid!

Nice video Emin .. I also had this similar problem a few days ago but I found out the VFD was set on a low speed but the customer still insisted for us to greased the bearings on the motor and pillow block bearings on the shaft also replace the pulley and belts ..

Great Video!

Great works Guys..

Did 1000s of pulley swaps like this on pumpjack electric motors. Sent it.

I love this guys sense of humor

Very Nice. That 's Cool

no chance very nice and i follow great job

Another great one Emin

Great video brother 💯💯💯💯

Another one down good vid

Hey emin big fan of your work. Can we be expecting any videos coming soon

When you were taking off the bushing for the sheave, you use the bolts as jacking bolts.

thanks bro

Haha 😄 you got balls. I snap them off nearly ever time I try it with a drill.

You made that look easy.

Video just saved me hours of aggravation. Thanks

I like. your videos Eman and I hope you make more HVAC call videos sincerely KZfaqr coin Slocum

Great video thanks

If you change the belt tention do you need to check the motor amps again?

I’m changing my air compressor motor for the first time. The pulley inner diameter is slightly different in size. Should all bushings slide that easily onto the shaft as easy as the video? Should I heat up the the QD Bushing to expand it? I notice the inside of the pulley is tapered in

thank you

I fucking miss this guy. RIP brother

Good job

Been down that road before! I cannot understand why they don't make these pulleys in stainless steel to last! The steel sheaves just deteriorate with all the chemicals we use in cooling towers. Thanks for posting!

very informative

Nice job emin where is your work place

good movie. a lot of of technician miss understand how remove and install pulley

Good video, I used candle wax, for noisy belts.

Emin are you with a pipe fitters Union?

HVAC tech thenks

Good stuff! Are you a building engineer or HVAC contractor?

Be snappin'....

Supper.

nice work tho

Haha I do the same thing with my ratchet and socket! Click click that 25 ft lbs👍🏻

great video I was wondering what city are you in, looks really congested lots of people and buildings.

Good knowledge sharing, could have been great without the vap waste of time and other stuff

If its not a split hub, I run the bolts all the way in and use the pulley like a slide hammer. Pound the hub off using the pulley

معلم

I do miss working on stuff like that!!!! Lol

how did u recondition the pulley ? It was completely rusted. Can you please show us

Thanks for taking time to do video whats your dogs name,, he looks happy

Hi,, is this taper lock 55 SF ??

what happened to ya man? really enjoy your videos....but I see you haven't put any new ones up in quite a while. everything ok?

No lock out tag out?

What happened to this guy I’ve been rewatching all his videos lol

what if the pulley is stuck on there , and been used wd40 and other penetrating oil, with no pulley remover tool?

Just by looks either 8v o d belts

Hey Emin haven't seen any new videos any more are you on a different channel or doing something else.

that's a big pulley

What are the bolts size did you use to take that Polly off

Not all startup tech know what they r doing emin. Just resetting to what they did. Could just be asking for future problems that makes u look bad. Spend a few n check alignment n tension. U can get trick with lasers on alignment but a string or straight edge work. Tension tool also

nice job poppy,whats the name of your company? if you dont mine me asking.

You pull a disconnect and don't open the door to ensure no knife's are broken ?

跟ㄊㄞ跟台灣差不多

cool video, you missed the use of anti-seeze and replace all parts... propper way

I put up my first vid this morning, let me know what you think.

this takes a lot of tightening

what is your salary ?

“Click click” LOL

I meant Cohen it is Cohen

Start off with the finger

Did you know, when one sheave is worn out, the other "just might be" also?

Bet tension The adjustment was poor. δ = 0.016 × Ls (mm)

벨트가 춤추네 ㅡㅡ 얼마못가겠군

Anyone Know what happened to Emin? He hasn't made a Video since 2015.

Our installation of V belt: kzfaq.info/get/bejne/qZ2Cjc6Kx67MnZc.html

Hahahaha click click.. hahaha

That motor looks bad

lol

No one wants to extract that!!