Must be what they made the Titan out of

I just looked it up. Dear Jesus, it actually was made from carbon fibre

@@TheWalkingRed yea it was partially carbon fiber pary titanium

Yeah, I can’t believe that after researching metals and carbon fiber videos on KZfaq for just a few minutes that ANYONE would be able to come to that conclusion! May they all see Heaven’s Gates.

@@markbaz4200 dude was playing with people's lives for 250k each

According to some studies, Carbon Fiber can withstand depths of over 7,000 meters. And it certainly survived several trips to the Titanic so it does work. The problem is that nothing can stand repeated dives, and as yet we haven't developed a good way to non-destructively test when Carbon Fiber has reached its limit. I should also point out that the experts don't seem certain yet the carbon fiber caused the failure. Several people have pointed to the very dodgy porthole, and some say it was the combination of the titanium end caps and the carbon fiber that was the real problem. Maybe it was even something else entirely, since it seems like safety wasn't exactly priority number 1 with Ocean Gate.

​@@rodh1404 nice

@@rodh1404 carbon fiber has ALWAYS been developed and used as a tensile reinforcement. It is common knowledge in composites that fiberglass performs similarly if not better than carbon in compression applications. Once you start pulling on the laminate in tension, carbon out performs justbout everything. I think this hull design just used so much of it (4" thick?) as to just brute force the calculations. But as many others have pointed out, typical composite laminations fail over time due to micro crack in the epoxy marix. tiny cracks occur and grow as the structure is loaded. Add extreme thermal cycling and the dimensional changes from the pressure and its gonna break down. Ive built a bunch of skis and skateboards and random parts from CF and glass, nothing too crazy but even with my basic experiences, i would NEVER pursue a CF sub for deep water. The only reason to do it this way is 1. probably cheaper than the extreme grades of metals required 2 much lighter weight, which means support systems for docking the sub needed to be much smaller and cheaper. also carbon fiber has proved time and time again that it is great at seperating rich people from their money. its a good buzzword.

“Rich people from their money” 😂🤣😆

Cameron should stick to making movies and STFU.

thank you so much

Thank u ❤️‍🔥

The titan submersible

@@soliderbred yes

You are the best

Stainless steel is pretty strong

"Titanium took 3x the force of carbon before it broke, but it also weighed 3x as much" This is true, but also the driving reason for asking why people hype it up so much if it's about the same as titanium in terms of strength to weight. Especially when you take cost into consideration.

al chile si

@@pcmasterracetechgod5660 Because you can form carbon fiber into virtually any shape without much issue while it would take a lot more to do the same with titanium. Plus the price is pretty much the same. If you are just sticking norm pieces together, titanium would be better. Make it a bit thinner than the carbon tube and you'd have the same effect. If you are going to have more complex forms and a low number of units, carbon fibre becomes more attractive. There is no absolutely perfect material.

@@carstekoch effect*

@@Emeraldd_33 Thanks, german auto correct took over.

😂🤣 You’re an ass! But you’re funny so it’s cool.

well... didn't say "do not try this at ocean".

Make sure you don't destroy the gamepad. We're gonna need it.

Sick people talking about a dead person, why is the world so evil.... I.e people

Oooh too soon 😆

Best thing about it is it's strength to weight ratio compared to solid steel. Lightweight and strong.

i was mo impressed by d stainless steel

They should've included a diamond pipe.

@@deancafe4739 haha cant b though

@@shackilleuhdeal7462 The low grade steel was "ANNEALED" for cold working by looking at it's behaviour in the test .

It's not like he wasn't warned about his deathtrap - he fired the guy who told him it was unsafe...

He was too stubborn to care. I saw a video where he was explaining his cutting corner design with cheap lights, bare minimum instruments and game controller drive. He was saying "as long as the main structure does not fail, everything else can fail, you will be safe". Anyone with common sense would be saying "at 3,800 m depth, NOTHING should fail!"

​@@granadosvmAccording zo recent studies, most people's common sense only goes to the shallow depth of about 300 m (on a good day).

Naaa, don't think so. Little d!psh!t CEO Crockton CRush would've just said, "Tech has advanced 10-fold in the last 10 months. My carbon fiber, on a scale of 1 to 10, is rated 11."

Unfortunately, the Titan Submersible was made before this channel.

This comment is underrated.

I did notice that when the carbon fiber gave under the pressure, it frayed rather than shattering like I'd have expected--is that due to it being woven in more than one direction as well?

Isn't this true to some extent with all materials? Is it just much worse with carbon fiber?

Unfortunately, people just keep repeating 'carbon fiber bad' without understanding why. It's not necessarily that it's weaker, it's that when it fails it's sudden and absolute.

Thank you for goodness sakes people are so quick to write off carbon because its "experimental" and not tested that material is plenty strong for 1 or 2 dives the deepest dive ever was done using carbon fiber 35k feet in the Marianas Trench and it was done once for a reason no repeated stresses.

Titanium kitni makhan ki tarah hua titanium bohot strong hao yaar 😊

Less than $600 can get you a 50t hydraulic press no problems.

@@Senkino5o Really? I Though their prices starts at least from tens of thousands...

No man, you gotta listen. It's dangerous. I just put back my hydraulic press once I read that warning.

Just take your hydraulic press to somebody elses home.

Instructions unclear. Penis stuck in hydraulic press.

💯💯💯

I think the speed that the material compresses is slower than the press

How tf do fish and soft jellyfish just swim around that deep like nothing is bothering them

@@nutinmyass by being mostly made of fluid, which is in practice incompressible. What makes certain animals (and poorly made submersibles) vulnerable to pressure is gas content, which has to drastically change volume if in contact with a dramatically different pressure environment

Pretty sure the prees reached 10 tons by the end for aluminum which was much higher than the 3.8 ton limit.

That kind of stretching strength is called Tensile strength.

The main failing point of the material used was actually the resin holding together the beam. Many people be like: “Carbon fiber is stronger than steel! It’s the best material ever, it’s the future…” blah blah blah. What they don’t realize is that only the mere “fiber” is stronger than steel. Common mistake. Even aluminum showed better result… I did expect steel and titanium to outgun it but the aluminum was a surprise. Most people that are into cycling should check this video out before dropping motorcycle money for a carbon toy. XD

@@danielhristov6175 You're missing the key advantage of carbon fiber: it's strong, but *LIGHT.* People don't like it simply because it's "strong", but because it's insanely light for it's strength. If you want pure strength, then sure, use steel. But if you need something that's light, but also rather strong, carbon fiber is an excellent fit.

Also, cf varies pretty wildly in quality

@@danielhristov6175 Compare the weight to the results and you get why carbon is a valid option. Carbon and Titanium have nearly the same result when weight normalized. It's a lot stronger than aluminium when weight normalized. That is where carbon fibre gains an advantage.

You mean *blow in*

Yeah

Over 11 million views. The entire population of Sweden is only 10,5 million! Well done.😊

@@disappointedbananas2365 lol.

Who would have thought.

Wallach 👋

I don't believe this is correct....... the reason there is not catastrophic failure (with any of the specimens) is because someone did their homework and solved for the necessary geometry/stiffness to induce crushing under compression rather than buckling (for example the J.B Johnson/Euler interaction curve).

Pressure made it heat up and delaminate? Basically melt? *the glue

Agreed, the test is completely unrepresentative on how these materials would behave with uniform external pressure as experienced at extreme depth. To be fair to the makers of the video; it was not intended to be.

fascinating! that makes a lot of sense, thank you for this comment. I guess engineers generally design structures so that any deformation is a failure, catastrophic buckling or not, staying within the safety margin established by a test like this.

Wrote too much for a simple concept: all kinds of fibers resist traction, not compression. Simple this way! On any pressure vessels made of any fiber, when the inner pressure is bigger than the outside pressure the fiber is under traction, but when the outside pressure is bigger than the inner pressure the fiber is under compression!

It helped that they aborted a good amount of those trips due to other complications

Well, this isnt really indicative of much. They crush carbon fiber in the direction of the filaments, which is much, much worse than how Titan experienced pressure. However, that doesnt take away from the fact that a carbon fiber based pressure hull is bad for external pressure but superior to any metal for internal pressure. So, if you wanted to build a tank to contain internal pressure, carbon fiber will give you the best result in terms of weight and maximum sustainable pressure. But dont make a sub from it...

Also the carbon fibre layers was 5 inches thick, so probably lasted longer but ultimately either end cap glue failed or porthole or carbon fibre delimitation within layers

@@GaniscolThe carbon fiber Mr. arrogant CEO used was not even laminated properly. It was all in one direction instead of crosshatched. 🤦🏻

Wear and tear was probably the reason it imploded too

Yeah, I would watch this video.

And tungsten

Was thinking the same thing

Genius video idea.

thx

So carbon fiber doesn't even have an appreciable advantage...

@@hariman7727 the price I think

@@hariman7727 Price and weight. But don't forget the cylindrical shape was also a problem. Spheres are strongest under pressure from all sides. Cameron used spheres.

So much for my brass submarine plans. 😢

Aluminium(& most of its alloys) has the same problem carbon has, cycle fatigue.

@@PebCak42 I'm sure you know more about it than I do. But looking at the way the CF shreds apart here, wouldn't water have an easier time penetrating it? In any event, OceanGate had no business taking people down there anyway. As we saw in the search for them, anything people can do on the ocean floor, ROVs can do better and safer.

@@nancymcmonarch I'm not that deep into carbon, but from what I understand it's not designed for that type of strressor. It performs reasonably well in the areas it's designed for, considering weight-strength ratio. I'm more into metals.... There are a lot of factors when it comes to materials, some just break/rip without any visible warning, some deform before breaking. It's very important to know what kind of stressor the material will experience... compression vs. tension, enduring stress vs. cycling stress, element exposure etcpp, do you need visible warning or do you have other ways to detect potential flaws & failure. E.g. certain parts for high performance engines are x-rayed for potential flaws that can't be detected any other way. It's a science in it's own right. But I agree, they had no business doing what they did, especially in the way they did it.

Nope

@@nancymcmonarch That's part of the problem with CF. Once any kind of fracture of the matrix occurs, water can penetrate and start pulling apart the layers, i.e. delamination.

Up

It wouldn't work on the metals.

@@pvpdm why wouldn't it work on metal? I would think you would see the temperature change. The metal may show its surface as an even temperature throughout the change, but it would still be visible that the temperature is changing?

@@rob_olmstead Crushing steel objects with hydraulic press THERMAL CAMERA EDITION!

@@marinetechknj it's because infrared bounces off of metallic surfaces if I'm not mistaken.

cf doesnt just fail when it fails. it fails like in the end of the video....catastrophically. Absolute insanity.

they didnt watch this videoes

…and for combining CF with composite materials and an acrylic porthole

To all the "Scienceticians" observing this anecdote..... The carbon Fibre tube is weakest at the ends. The diameter of the press forces the cylinder BETWEEN the layers of carbon. So, the "failure" you see is the least surprising outcome there could be. Aside from that, CF if an additive material, titanium is a "contiguous" material. If you want the strength of Titanium, simply add more CF. As a test of perspicacity, several of the audience fails.

Ouch. Maybe too soon,but spot on.

😂😂😂😂

If you look at the pipe here the weave of the fibre shows it going in two directions increacing the strength. The sub only had the fibre strands running in one direction so not as strong as it should have been.

I just feel like metal is somewhat one piece so it won't really make a hole unless something punctures but carbon fiber has so many weaves that there's so many possible places for holes. It probably good for something on land like body armor where you don't have water seeping in and it's tough and lighter than steel but I wouldn't trust it going to a really deep depth where everything fails all at once and you don't know what hits you

@@MrLuffy9131 it didnt leak water... it delaminated lost its strength and failed. if it were to have "leaked" it wouldn't have been imploded. the cabin is pressurized with oxygen right so if it were to leak it would be constantly fighting the pressure of the fluids around it. they would notice the pressure instability and surface but it failed almost instantly with no possibility of taking on water.

The titanium (and steel, PVC, aluminum, etc) in this video failed by yield, which is gradual and detectable. Cyclic stress and fatigue causes failure by crack propagation, which can be much more sudden. Titanium is susceptible to fatigue cracking no matter how high the yield strength, so it must be designed with a maximum number of cycles in mind (just as the carbon fiber in the titan should have been). There's no good reason to make a sub out of carbon fiber, but with properly calculated fatigue life, it could have been safe just like titanium. Really though steel would be the better option because it has a fatigue limit, where if each cycle doesn't exceed the limit, the vessel will always be safe. In some cases it may be cheaper to simply say that the vessel should only complete x number of dives, which is acceptable in most materials, but at the end of the day steel is the only material with a real advantage there.

Many metals will "complain" either visually or audibly when stressed.

It doesn't fatigue quickly. Many aircraft manufacturers are using carbon fiber wing spars because their fatigue behavior is much better than aluminum.

carbon fiber is very durable and has a long lifespan. the same piece oceangate got was a recycled piece from an old aircraft.

Half of a wing is in compression so CF is not suited.

@@larrybe2900 Bike frames are made from carbon fiber everyday. The top bar is under significant compression. Wing spars are indeed made with carbon fiber caps separated by a shear web. Carbon wings are quite suitable. The compression strength of titanium is 50% of its tensile strength. The compression strength of stainless steel and aluminum is 40% of its tensile strength. The fact that carbon fiber is weaker in compression is like every other structural material.

@@FlatOutFE in tension yes.

The comment I was looking for! Thanks for saving me the hassle 🙂

Nice

Acrylic and pvc are about 50% and 300% stronger than brass respectively. I would have never guessed it

titanium and brass are wrong, they started to deform way before the marked pressure in the video - watch it again Brass started to deform clearly around 1900-2000kg and Titanium started to bend around 7000 already, while carbon fiber held until 2900.

@@blinzi69 What's being measured is the max pressure it can withstand before catastrophic failure. Deformation obviously isn't good but it's not up to the level of catastrophic.

Carbon fiber used as a building material is not the problem. Using it repeatedly without a proper way of testing its integrity after each dive was the problem. Having a submarine with so many glitchy, twitchy, defective safety mechanisms and systems in general was also a problem.

me

Yep

Me best for submarine metal stainless steel

Think Ill place all my bets on titanium thanks .. watching that carbon fiber tear lol

It's me! It's MEEE!!!!!

metals fail but still retain "somewhat" of a shape and sub occupants might be crushed or might have small chance to survive. carbon fiber was literally "catastrophic" failure with zero chance of survival after failure of crushing integrity. It shatters instead.

It wasn't an engineer that thought carbon fiber was a good choice. In fact the engineer that quit did so because carbon fiber was chosen.

not really, titan is a very poor example of that conclusion. it probably had faulty engineering for where the titanium was married with the carbon fiber hull, faulty method of applying the carbon fiber/production of the hull itself and faulty shape for deep sea diving. just to name a few. it probably had sub par solutions all over it

@@zlonewolf probably `easily` avoidable by making the hull much thicker, so the design could theoretically much deeper(even with this shape). not having a subpar marriage of the titanium and the hull(thinner lip to support it and just glue used). not to mention a pressure chamber shaped like sphere instead of a tube. any material could have failed with this design

How about all those expensive bicycles out there? I feel safer on my old steel Schwinn.

amazing, you possibly saved him from a calamity of epic proportions!

Bullshit.

@@mattmarzula wooosh

Sarcasm Level Infinity! ;)

the sarcasm was so strong I didn't realize it was a joke at first

_I'm bulletproof, nothing to lose_ _Fire away, fire away_ _Ricochet, you take your aim_ _Fire away, fire away_ _You shoot me down,_ _but I won't fall_ _I am titanium_

@@Model3GenerativeANdroid The A-10's "bathtub".

they did... but only for the endcaps... which survived generally intact, of course.

thanks

Thanks for the table summary. I was just thinking of doing the same and then saw yours. It's interesting that titanium, carbon, and stainless all have the roughly the same compressionc strength(under a cylendar form) per weigh.

So should I be glad my teeth are acrylic ?

Thank you! I wanted to know this, but was too lazy to do it.

Awesome! Another important factor that could be use to sum up in the ratio is the cost. This is one of the reasons SpaceX choosed Stainless Steel instead of Carbon Fiber at the Starship and Booster

Me😅

wrrg, no such hting as grade or high, low etc

and yes if we add to that its performance depending on how much one gram costs i think carbon fibre will come on top since satainless stell and titanium are expensive metals

wow glad I read the comments before I got out the calculator. Well done. One must be mindful that this test is simply compression, that's why material engineering looks at l stress in many ways. We developed a ceramic epoxy that wets out a Kevlar wrap on a structure for abrasion resistance. Carbon fiber would be toast in this application. Always good to know as much about the test as possible.

@@xVERT4x ... as well as the B787 Dreamliner aircraft.

@@go-wycowboys5018 That reminds me of that steel tank they added to the front of a fiberglass boat, and was rubbing for years against the hull, then one day, in the Caribbeans, middle of the night, they had a big waterway and almost sank. For the record, they got saved by a fishing boat nearby that heard the mayday call and had a quick fix bi-component compound on board. So yeah fiberglass and abrasion are empirically confirmed.

I think the shape of each material would affect this ratio, if they were all spheres for example, their strengths would be different.

you wrote "Carbon fibre is not even as strong as aluminum" but aluminum has a strength of about 500 kilonewtons compared to carbon fiber which can have up to 1600 kilonewtons of strength

@@commendatore2516 beause people dont understand how cf works. In this case where hes basically pressing the fibers downwards the main force taker is the resin. However the resin only is an addition to fixate the fibers in position. The fibers should take the load, which they do best in tension directed to the fibers. Pointless comparison like this. And as you said, aluminium is not stronger than cf. It just so happens that aluminium is isotropic (takes forces the same no matter which direction) and cf is anisotropic (force taken depends on direction). A well built carbon part will outperform aluminium anyday. Yet, depending on application obviously, maybe not for a sub, but definetly for any other "normal" application like car parts etc.

Carbon fiber is as durable as pvc 💀

Carbon fiber is great for most strength applications but not for compression. As you can see in this video, the hydraulic press compromises the fiber one strand layer at a time.

Oceangate?

​@@parvesh.5_357No, the other one.

@@bishopp14 😆 hahaha

Who gives a Sht! about rich tards that want to see ship wreck?! Everyday innocent ppl and children die all over the 3rd part countries and you don't whine...

@@Fairlane55 😁

Pull strength it will behave another way yes also directions of the strands shows the structure of the force must be applied by the way carbon material used is not advanced one just lining

Agreed light weight tensile strength is the benefit of carbon fibre

But overall Carbon fiber is overrated especially in car industries. True it’s light but is not as strong as aluminum even!.

carbon fiber don't take compressive loads? umm you should turn on the TV and watch some F1 racecar's wishbones...

So, don't build a pressure vessel for a submersible out of carbon fiber, is that what you're saying?

Make flat bread.

Hydraulic pressed orange juice hmm :D

Given recent events, some people do have to be told not to put carbon fiber under immense compressive force

the ironing

😂my wife's cakes are sometimes so hard they could be parts of that hydraulic press

Yes. He does have a video with titanium and CF plates, doing bending tests. Not cylinders pressed from the side, but still interesting. I'm going to watch it now. [correction:] The video shows bars from various materials (not "plates").

Probably a lot less pressure if done that way

@@tubularap from the sides? would be nice to see who wins PVC of CF

@@kiyoshim9593 - Yeah, PVC was remarkable strong.

It wouldn't matter as this also would be unrepresentative of the uniform external pressure experienced by a sealed container at extreme depth. To do this you would need to make a sealed vessel, place it in a pressure chamber filled with water and then increase the pressure of the water.

Nah, this is "old white guy" technology, so irrelevant to Oceangate.

I guess they uploaded on KZfaq too late

Yeah that one surprised me as well.

If you saw a serious testing of acrylic it will shock you for sure, the testing on this video is done by a non professionnal, acrylic is used in field where he outperforms even stainless steel.

Yeah same thoughts here , very tuff stuff for plastic.

Geometric

yeah they are really strong

The Trieste used a tank of gasoline for negative buoyancy. That's what I would do as well. The tank doesn't require a large wall thickness because gasoline weighs about 6 pounds per gallon and is not compressible but salt water weighs about 8 pounds per gallon thus you have 2 pounds of negative buoyancy for every gallon of displacement.

Remember when Stockton said ohh "this is bouyancy foam it's is very expensive" and that's what happened

Don't forget Stockton Rush was an aviation engineer. He could be possessed by these "high tech" materials and consider "traditional" materials inferior, old school, not innovating enough.

Stockton confused his submersible for an airplane. He thought he was design ing an airplane to go underwater.

@@enchantereddie Fact: there are more airplanes underwater than there are submarines in the sky. LMAO

Yep.

Not really, different loads involved. Subs get squeezed from all directions, not just top to bottom.

At this rate , everyone gonna get a degree in mechanical engineering 😂😂

Where ya from ? 🤨

The carbon was significantly thinner than the titanium.

The CF on the Titan was actually weaker than the one in this video. CF tubes are stronger at taking compression when vertical than horizontal. Titan was doomed to fail.

And nobody makes subs from titanium either. Steel is the best material that is relatively cheep for what it can withstand.

@@forbidden-cyrillic-handle Yeah they do. RUssians do it all the time but guess what. most titanium comes from Russia. Anyways the best thing ocean gate could've done is to just use a steel pipe and add more bouyancy

@@zarbon700 thats even crazier

Which is also why you don't book passage on a submersible without proper certification!

I guess the stainless steel specifications are much higher than avarage, than we imagine. I mean that's not some common pipe, but some exclusive technologies, like for nuclear plants or so.

The stainless was also solid, not a tube, according to the caption. This will alter the results of the test.

@@rb032682 I don't know what he meant by "solid", probably smth related to material specifications, but it was tube, the stainless steel. In the presentation, when he measured diameters and thickness it was tube, and at the end when he picked up the deformed chunk it was also tube.

British Stainless Steel

Stainless is strong but not as strong as many Steel alloys. Some steel alloys are really strong but hard to work with, hence engine steel blocks are so expensive to make.

@@kiyoshim9593 This is true. Tool steel is strong, for sure, but brittle after heat treating. A sample of the same dimensions as these would have broken, instead of folding, in this test, but probably would have held up to more pressure than any of the others. That would have been interesting to see, also. It might have damaged the press, though.

I once bought some armour plate steel, apparently 30% tougher than standard NATO spec , the guys also said they welded it with stainless steel rods, so I guess it was similar in composition, so the toughness demonstrated here does not surprise me. The Russian Mir subs use 50mm thick maraging steel alloy.

@@Jagdtoq Uhm. Stainless steel have many variations. one costing 4 times more than the others. so its meh.

My top fuel dragster has a compression ratio of 25,000:1 on 8 hydraulic press cylinders. It's an external combustion engine. Runs on Vaseline glass. 😂

Yeah, anyone knows what the ends of the hydraulic press are made of? Especially the lower one that he moves around freely?

@@Dipj01 Hardened/Tool steel typically.

​@@Dipj01I don't know , but probably good ol' NY steel ot Pittsburgh. I don't know man I'm not an engineer just a pawn in this world