Low hours. You got a heck of a deal. Worth twice that price. A new model of that would cost $65,000 and may not serve your needs any better than this one.

Hate to state the obvious, but off rd and on road diesel are the same ULSD product now except for the dye. Not a contributor to smoke. Great buy, yes. Congrats

That's a good man there. I sell everything the same way. I sold a generator years ago and told the feller everything about it. He haggled the price UP! A few hundred more, and thanked me multiple times for being a straight shooter with him. We take really good maintainance of our stuff though. I know stuff happens, but I would feel bad if someone felt I cheated them.

Congrats Dave, on buying ur 89 Kubota Kh040 Excavator. don't forget to grease the rollers/wheels on the track. sounds like they need grease.

Red or off road diesel does not make a machine smoke more or less than clear (on road) fuel. The owner said it smoked but cleared up after a few minutes of operation, Sounds like an oil issue NOT a fuel or filter issue. FYI.....I have 7 machines that all use red / off road diesel and none smoke.

Dave, you might look at spraying out the fins on the radiator, they look to be clogged with dirt. Could affect it operating if you dig all day with it. Just an idea. I hope the machine works out good for you 👍

Now it’s serviced.👍

I like these older machines better. 👍🏼

I would have 100% jumped on it that price.

I have the KH50. Bought it at RB Auction for $7500 canadian dollars. 2400hrs. No need to go to the dealer, it is grey market the dealer does not want to talk to you anyway. All parts on the machine are available aftermarket. Example engine is a D950. Glow plugs will pretty well guaranteed to be burnt out try for 11 amps each total 33 amps on the main wire with your clamp on DC ammeter. Glow plugs are standard crossed it to bosch to avoid the dealer. The cylinder seal any hyd shop can source seal sets I repacked 4 of the cylinders. Hyd hoses are NPT and ORB nothing special. On the NPT had to use liquid loctite hyd thread sealer. Tape and pipe dope did not seal. Undercarriage did all the rollers with off the shelf metric bearings and seals. Tracks replaced from local track specialty supplier. Idler bushings made them myself on the lathe from a chunk of brass stock. The controls have those heim joints, these are readily available too no need to go to a dealer. Made a custom sized hyd thumb with a 3 way 12v valve off the bucket hoses. Press button for thumb release for bucket using same controls. Pins and bushing are all worn out so have been replacing these with standard size after boring. New seat was a $75 special from Princess Auto the canadian equivalent to your tractor supply. There is a suction strainer inside the hyd tank. Condensation in the hyd fluid makes this strainer plug up with ice in winter and you get zero movement. The strainer is an off the shelf NPT thread. Take the strainer off, thaw it on the woodstove then put it back. Hyd oil up to your elbow deep. Carefully check the supports back of the roll cage mine were rusted to the point the whole canopy was ready to fall off. Funny that was the only spots rusted badly. Still to do is the main boom to base joint. Mine is so badly seized tried heat and 20 ton press still could not shift the pin. The swing cyl is worn out at the cyl end.

People are way different over there. In Britain youll list it for 10 grand and the guy will show up with 7 grand and pretend it's broken and only worth 6

You should lift up the side of the machine you are trying to tension the track on. There is a spec for clearance between two points. Over tensioning can lead to track damage. Great vid. New sub. I paid 9K for a 2011 Bobcat 325 with 1926 hours on it with a hydraulic thumb and love it. I live in upstate NY and equipment is hard to get unless you want to do allot of work on them. You did the right thing starting fresh with filters etc. no matter what the seller says.

You are a hard working young man. Keep up the good work...

Great editing, Dave. 👌 subscribed

"....I better get some seat time in this because, uhh, I'm just going to embarass myself." Nah, Dave! All of life is an exercise in learning and having some fun while you learn. I enjoy your videos, keep 'em coming. 🙂

Very good. no lengthy opening and closing credits. straight to the point. I like everything thoroughly. Maybe I'll apply as a mini-jobber.

Looks like a solid machine! Gotta find a trailer to demo now!! That will make loading those dumpers a lot quicker too!

Just a small note Dave.I would avoid using that high pressure sprayer underneath up close to the swing bearing and seals.Most areas are okay,but avoid this area when pressure washing.the last thing you wanna do is change a swing bearing.Nice work.

That radiator is REALLY packed with dirt !

Not bad for a 4 tonne digger, hope it comes handy for you

Im glad one of us snaped out of it. I would have just kept looking at it

I think a good winter project is putting a Hydraulic Thumb on it if possible. I think you need one for loading dumpsters, it would be more efficient.

Sunbelt Rental charges $700 per day for an 11,000-pound excavator, whereas the one featured in the video weighs 12,000 pounds. It could pay itself off in one month.

Большой лайк 👍первый американец который МОЕТ технику ДО ремонта а на ПОСЛЕ 👍👍👍

Looking forward to more videos. Looks like a great machine for 8 grand. Would look great with a fresh coat of paint and some fresh decals since the sheet metal is pretty straight. Super low hours for the age too.

Dave I can’t believe how big your puppy dog and Andrew’s fur baby are growing up to be so big. They are so awesome looking. I’ve never seen Labs with that color fur before until watching your videos. That was super cool that you you hooked Andrew up with a puppy. Your a good dude👍❤️🙏

A steal bro. Glad I don’t sleep, as I found your channel. 🤣 ✊🏻🖤

That is a well greased grease gun

Like the new Kubota exc, it look good .

Seems like a good price for that size of machine!

Put in dumpster then smash. Less clean up. Might want to check the rollers out to make sure none are locked up or bearings shot also

Thank you for sharing , i learn a lot , good job 👍👍👍👍

Give it some love Dave they are a good machine you started out right goods clean and a service and you know it’s done mate

That was a sick deal ! $8 k for a very decent mini Ex! Damn good job ! Andrew is proud of you! FJB POS

Oh man I loved the way you started your video with a pic of your dog. I subscribed.

There is usually a filter inside the hydraulic tank on the pick up to the pump wouldn’t be a bad idea to take a look at it

My follow from Sevilla,Spain. Congrats.

9/11/23; Dave, congrats on yur 'new' Kubota Excavator! Always enjoy your channel, hard work & get-the-job-done attitude! Best wishes from NewOrleans area. Am sure you & AC will have many conversations about this equip. Glad you made the purchase. Also appreciate your straight up talk & video showing $/ price paid. You are showing all we YT viewers how an Honest man handles new purchase of this equipment. A+ Dave! Don't think guy u bought it from did any of 'service' work. I watch several other channels (Farmcraft101, SalvageWorkshop, Diesel Creek & others) who buy used equip & dirty fuel tank is always source of engine performance issues. Hope you are ok on this. Stay safe & carry on!🔧⚙️💪👍🍺😊

I think a former company (that owned it) called it a KX 151 (Kubota eXcavator 151) for their own purposes and inventory. I think this Kubota mini excavator is actually model KH-040. Just thinking out loud. Good find with whatever numbers !

There is some nasty bugger weld repairs to the bottom of the mast right at the pin. Probably explains the cheap price. Good luck hope it don't cause problems in the future.🍻

Dave was $8k a great deal or ok deal? I have no idea what they go for at that age. I do know Kabota is a great brand with a lot of dependability, so that’s great.

Great video dave I love this stuff!!👍👍

Great buy Dave⭐️⭐️⭐️⭐️⭐️

Yap David you differently ned a hydrologic thumb on is much better.

Good video! Love your channel name lol just subscribed

I have seen alot of used equipment on youtube, but I think you got a decent deal on the kubota.

Good price for a machine that size. I paid $8000 for my 3500lb takeuchi mini ex and it's been a workhorse for 5 years now. Even if the engine needs sleeves/rings its not too hard of a job

Hi Dav COOL VIDEO

Ya,, that ol girls antique but it will do what you want it to it’s a pretty decent machine,

Blue tooth compadable.✔️

Good deal! Best of luck with it, Dave! My Yanmar has a hydro thumb but it's got a real short throw. Every time I use it I say the same thing as you did. "Useless!" Make sure you get a long throw piston if you upgrade to hydraulic!

Congratulations!

You got a really good deal at 8 grand imho. Honestly you could turn around and sell it now that you did repairs and do that same video again (great video). I bet you could even sell the machine to a viewer (I would buy your machine if it was in Indiana).

A good buy, I think you will get lots of use out of it.

Feel like I'm watching Andrew Camarata. :).good job bud.

Thanks for the video.

Looks like a decent machine Dave , I see that when you was loading the dumpster that the engine smoking had stopped. Maybe an oil change was what it needed to stop that? Off road Diesel has changed Dave , here is a little bit of an article that I found on it. Wishing you all the best with your new equipment! 👍 On-Road and Off-Road Diesel - What’s the difference? There is no chemical difference between on-road and off-road diesel fuels. On-road diesel, also known as clear diesel, can be purchased at the local gas station. Off-road diesel is dyed red and is sold through bulk distributors. The only differences are in the color, cost, and intended use. In the past, off-road diesel had a higher sulfur content, which caused a smokier burn. With changes to fuel specifications from the Environmental Protection Agency (EPA) gradually implemented beginning in 2008 and completely enacted in 2014, the two fuels are chemically identical except for the coloration. What Is Off-Road Diesel? As the name implies, off-road diesel is for use by farms (agricultural use), industrial, and construction vehicles that do not travel on public roadways. It is not taxed, which allows a lower pricing scale. Using red-dyed diesel in the truck you drive to and from work could net you a hefty fine. Nontaxed diesel fuel uses are defined in both state and federal tax laws. While the federal laws are applicable in all states and territories, some specific uses may be permitted within individual states. Tax rates also vary from state to state, although the federal taxes remain the same across the board. The goal of increased regulations regarding off-road diesel is designed to reduce emissions control as part of the clean air initiative. By reducing sulfur content, off-road fuels are producing fewer air pollutants. In many instances, exhaust emissions have been decreased by as much as 90%. Emissions standards for diesel-powered marine vessels and locomotives are not included in current regulations. There are plans to revise and apply a more strict policy regarding these uses in the near future.

Change final drive gear oil. Some rollers are filled with oil sealed . You may wanna check them squeaky. Check rotary hydraulic swivel for leaks . Clean hydraulic and fuel suction screen in tanks. Put one gallon of Lucas hydraulic oil seal conditioner in it. Stops small leaks softens old orings plastic packings . Good machine for price👍 I have a old Yanmar and a newer 2016 CAT 308e which already needed $7000 in dealer service for DPF and computer. My old Yanmar 1994 never once broke down. One hose and tracks.

The radiator looks like it would benefit from being blown out with some compressed air, it looked clogged. Have the hydraulic line pressure checked, it looks a little on the low side to me.

Well, sir only time will tell on its worth, but damn, can’t believe all the straight sheet metal…

Started the video- thought I was watching an Andrew Camarata video :)

Great machine for the money. Not all dented and leaking. You could really benefit from a hydraulic thumb i agree.

I always seem to learn a trick or two from your channel. It never dawned on me to buy the pails of Shell Rotella, and break them down into 5 quart containers to make it easier to handle. Efficient and $ savings too. Funny thing was. When watching this, you captured a storm coming in. And here in Connecticut the exact same thing happened 3 days latter. Absolute downpours.Pretty crazy. Also, bet your glad you have plenty of space at your new shop. At this rate your going to need it. Take care.

Not bad man. I’d say you did good for the size of machine that is

Thanks for this

You forgot to blow off the radiator, looks plugged up

good stuff. love learning on how to do maintenance on these machines. one day I'll have my own. why is it squeaking some much when driving? sounds like some bad drive bearings that are very dry.?

Go talk to Andrew, he will help you sort the thumb & the controls out 👍👍🇬🇧🇬🇧

My grandmother used to have a metal lawnswing made of the same pattern as that front platform guard. Lol

Nevermind bud I see if you got Napa filters on some of that stuff yeah don't look like they did any kind of service on that thing bro people lie just to make money no but we had one and we had to replace the hydraulic pump because the arms didn't want to move to good and that's the way they Linares looking let me know if you got to change it cuz you got to luck trying to find one so let me know thanks

Hey Dave just let you know Napa can carry all those filters and stuff bro

Gotta try the bag over the filter trick to save a mess

Got a good machine right there Better than using your back Hope it works for you seeing the next one stay safe have a good day

Sellers almost alwYs decive buyers, I never trust anything they tell me. I used to sell used autos and always told my buyers what was good, bad or needed repairs. I built up decent customer base by telling the truth. Still do the same thing today but it's rare, IMHO.

Red diesel doesn't smoke any more or less than clear diesel. 8 grand was a steal for that!

well done Dave from uk

Using "off road" fuel does NOT make a diesel engine smoke! The only thing different about it, is the dye they put in to show you haven't paid road tax on it so they can lock you up if you're caught with it in your "on road" vehicle. I've ran farm equipment for decades with off road fuel, and none smoke until there is an engine problem. A little smoke on start up is quite common though.

Dave I think you have a top or bottom roller bad have fun with your new toy

Great deal man I am jealous

alot of the functions seem slow in one direction and faster in the other? or is it just not moving much fluid and everything is slow?

We see storms all the time like that in Florida

I may be a bit early, because I haven't finished the video. There is a small lever, to the right of the compartment under the seat. Moving that up or down, should change your controls. Looked to be a thin rod with a finger loop.

Great video Dave, I have a JD 320E skid steer, I am about done with it, would like to sell eventually and get me an excavator.

Hey DD.. whats the yellow boat behind the dumpster at end of video?

Is there any way to add coupler for a hydraulic thumb ?

I think Popeye tightened all the filters. LOL

Of course you have to be on your phone while backing it off the trailer.

Love the vid. What’s up with the yellow boat in the back?

Does it have digging power? I would of hogged some dirt before I bought it.

Congratulations

Nice buy Dave, should get plenty of years out of the ole girl. That is if you do not up grade in the future. But either way, good buy.

nice machine!! Where abouts are ya located? baroni recycling isnt too far from me!

*Not sure I missed it but I noticed how dirty the radiator was, cleaning that will make that run way better less heat, I’ve bought few machines and they all got very hot or overheated and hence why those sellers sold just saying*

Would be cool to see you get a working thumb hooked up. It It would make a cool Andrew collab video.

OOOOoo ooch! Couldn/t believe it when you fetched out all that Green for a smokey Joe at nearly 4,000 hours! Is that the market Stateside? I should live so long! That machine in England would be half that price and if you were a seller - it might stick. Auctions are fully of them at scrap money. That said, it doesn't look a bad machine, all the pins seem tight ( oh dear, I've just seen the repair to the dipper!) and under carriage - the old models with long lever controls always need attention - and usually when you've driven it into some godawful position - in winter. How very dare you do preventative maintenance - showing the rest of us up! Best of luck with this - now I know you're here I'll pop in every now and then.

Every time somone buys used equipment they got to wash all the mud and grease off. That stuff makes it run better.

That's worth 20k here lol nice find

a backhoe just sold near me for $750 because the backhoe hydraulic pistons were removed. came with replacements but needed the work.. i'm kicking myself for not getting it.

Hes not really wrong though, with a switch valve you could change whitch way the hydraulics flow. I know they have manual switch blocks but theres also button activaded ones witch may be way more useful.

Wat u could do is run a deverter valve of some with couplings and a push button switch to clamp and unclamp a hydraulic thumb like the tractor Andrew might have some other ideas on how to do that that thumb is useless and in the way😊