After 3 days on the trail and soaked from a rain storm I have no choice but to sleep in a dirty old Cabin with packrats,mice,ants and spiders.
I keep seeing Grizzly bear tracks that lead right close to the cabin. There I find a tree it has taken a bite out of as well as claw marks carved on it. There’s no door on the cabin and the roof is missing in spots.
FULL VIDEO HERE-4 DAYS ON THE TRAIL PART 1.
• 4 DAY SIDE BY SIDE ADV...
*Here’s a few links to some of the things I use on my adventures.
You can buy them off Amazon. I won’t list anything that doesn’t work good.
*Here’s the HUGE sleeping bag I use and I love it. This thing is cheap to buy but very durable and comfy. My last Coleman sleeping bag lasted me 18 years! Check it out.
amzn.to/3P0XUwh
*** Here’s some Amazon links to the parts I used for my Chinese side by side. I only use the ones that work good.
*ENGINE iCE coolant. This stuff works!! amzn.to/3OnJG8g
*Oil Filter- These 700’s have an oddball oil filter that is NOT the same as the 660 or 700 Yamaha Rhino. Here’s the link to the filter I use amzn.to/3RSIhJV
*Clutch Shim Kit-I used these shims to lower my low end gearing. These sxs’s are geared taller than the Rhino so need all the help they can get. amzn.to/3RPodrP
*Mishimoto Oversized Radiator- this was a game changer and makes the engine run so much cooler than stock. It’s for the 660 Rhino so it IS NOT a direct bolt on but easy to fab up brackets to make it fit. My engine never goes over 175°F even on long steep climbs on hot days.
Keeps everything much cooler and more reliable than stock. Watch for my video showing how I made the brackets. amzn.to/3v4bY0P
*Exhaust pipe header wrap-This stuff works awesome at keeping the heat down around the engine.I just wet the header wrap then installed and despite bad reviews it’s holding up great. I think the key is to lightly wet the wrap before install-amzn.to/3oeHDJn
*Exhaust pipe gasket and headpipe washers/gasket- These seem to be working good no leaks after a couple hundred miles. amzn.to/3zm1oVA
*Choke Cable-surprisingly this is a well built cable and fit 100%. I usually like to buy Yamaha cables but this one is high quality plus over half the cost. amzn.to/3ojeahu
*Air Box boot- this goes from the airbox to the carburetor and it did fit but it had no recess like the stock one had so I had to modify it. It would have still bolted on but I didn’t like the lip of the carb sticking out. U ground the edge with a dremel and it works fine but i’d use a factory Yamaha 660 Rhino boot if I did it again. If you need it fast though it will work. amzn.to/3OvumXC
*Clutch cover Rubber gasket-Fits perfect- amzn.to/3cr02zS
*4 wheel drive servo motor- if you need a new 4x4 electric motor this brand works great. Bolted right in.
amzn.to/3czmqHy
*steering rack- this bolted right in and fit perfect. I have a couple hundred miles on it and will do a review later to let you know how it holds up. Much cheaper than buying a Yamaha rack and convenient to buy on Amazon.
*Gear shift boot-the stock one was all cracked up so I ordered this one and it seems high quality and fit great. Also it doesn’t have that horrible made in China smell that lots of the older parts made there used to have. amzn.to/3aXwvxu
*Oil pressure gauge- digital RED gauge with the pressure sender as well. Don’t forget to ground the metal gauge or it won’t work! amzn.to/3PEhfEV
*Starter- this starter is the DB electric brand and it works great!
It turns my engine over much faster than the original. I put silicone around the seams to keep water out and 3 years later it’s still working great. amzn.to/3yQkh1s
*Ball Joints- these are the All Balls brand and normally in the past I did not have good luck with these. It looks like they upgraded the boots and other parts of them now and so far they are still nice and tight. Make sure you freeze them for 24hrs the heat the knuckle up and they will slide right in no hammering needed and best chance of them lasting a long time-amzn.to/3v78Wcf
*Front Wheel Bearing kit- this is the Pivot Works brand and I’ve tried all brands of bearings and have great luck with these vs other ones.
One pack will do both front wheels and they come with excellent oem quality wheel seals as well. No complaints and make sure to freeze the bearings for 24hrs in the freezer then heat the knuckle before install they’ll slide right in.
Front wheel nut torque on mine is 190ft/lbs make sure you torque them don’t guess or you will have play in the bearings-amzn.to/3cyqY0R