If you have a cooking oven you can also make dry carbon fiber parts. [DIY] (Making Engine Cover)

Рет қаралды 730,552

9 ай бұрын

#carbonfiber #drycarbon #enginecover
If you have a cooking oven you can also make dry carbon fiber parts. [DIY] (Making Engine Cover)
How to Make a Dry Carbon Fiber Engine Cover.
How to Make a prepreg Carbon Fiber Engine Cover.
How to Make a Dry Carbon Fiber Parts
Making Dry Carbon Fiber Engine Cover
How to make a mold for carbon fiber
How to make a fiberglass mold
HANKUK CARBON
Website : www.hankukcomposites.com
Linkedin : / hankukcarbon
KZfaq : / hankukcarbon
#카본
#드라이카본
#엔진커버
만약 당신에게 오븐이 있다면 당신도 드라이 카본 파츠를 만들 수 있습니다. [DIY] (엔진커버 만들기)
드라이 카본 파츠 만들기
드라이 카본 엔진커버 만들기
카본용 몰드 만들기
FRP 몰드 만들기

Пікірлер: 144

@ourtorreslikestoreviewandp2108 9 ай бұрын

My experience of Laminating, would be to lay the long piece first, then put the strip around the coney part. If it’s a seen part you won’t see the join that way. Also I would cut the strip at 0-90 it’s easier to work round corners, the weave should be straight not at a 45 degree angle

@sgsuck109 8 ай бұрын

Great video, but please wear gloves. Epoxy is bad for your skin/health and also the pre-preg will be contaminated with grease from your hands

@mcpotx1nonly 9 ай бұрын

You need a filament dryer for your cf nylon. You won't need to sand your 3d prints anymore. Run it at 70c for 24 hours then run a ptfe tube to the printer prints will come out way nicer

@danboyes7477 9 ай бұрын

Looks amazing, well done! Loving your work as always 👍

@user-wf4iz5wj2c 9 ай бұрын

가끔이라도 올려줘서 너무 좋습니다!

@ronbaer67 9 ай бұрын

great creativity in your project but a couple of suggestions, 1) use a fine hair like camel or horse hair brush as it leaves a better finish so less prep and 2) work on keeping even spray patterns for more even coats

@darkwafflez_6190 9 ай бұрын

would you be willing to compile a list of materials/tools to attempt this project? I want to make a carbon engine cover for my 335i lol

@vanchaa1 9 ай бұрын

Gelcoat Black, Glass fibre staple, epoxy resin for the mould. Prepreg (dry Carbon + epoxy works also) release agent, release film, Vacuum bag, cotton flece. You also need some filler, sanding material, scissors, flex / dremel whit diamond blade, knife, wooden wedges etc.

@namrokmc7364 9 ай бұрын

와..자주보는데요. 대단하시구. 멋지세요.

@jhj7460 9 ай бұрын

진짜 많이 기다렸습니다

@Generalusuer 9 ай бұрын

Fantastic work🎉

@alexde4310 9 ай бұрын

Good job as always 👍

@abovewongart 9 ай бұрын

that's incredible

@viajando-con-edgar 9 ай бұрын

Exelente como siempre amigo!

@shanyebyt4899 8 ай бұрын

How much would something like this cost, material wise, if i were to do it myself? Thanks.

@bae_ru_ru 9 ай бұрын

포지드카본에서 드라이카본으로 새로 만드셨군요~

@hohomandoo882 9 ай бұрын

기다렸어유....진짜 영상 잘봤어유^^

@EliudUrba 9 ай бұрын

Interesante, crees que se pueda poner un aislante termo acústico tipo kilmat por la parte interna, a modo de que cambie el sonido, saludos

@Reddot_AUTO 9 ай бұрын

아 정말 배우고 싶은 기술입니다. 이런거 배울수 있는 국비 교육과정은 없나요?

@hockysa 9 ай бұрын

didn't you get an ultrasonic cutter? I thought you would use that over the dremel.

@macolaiden 9 ай бұрын

Perfect You're still here ❤

@sewerynbudziszewski8219 9 ай бұрын

czy piekarnik do pieczenia też się sprawdzi ?

@SHADOWBLACKs650 8 ай бұрын

I make them for RC bodies, you got it down correctly, except don't use the min wax, use the automotive polyurethane clear and it's a dream when finished... 👍

@hetori9918 9 ай бұрын

Dude you are a pro

@joscythe556 9 ай бұрын

I advise you to use non-perforated release film to prevent dry spots and pinholes in you parts. There wouldn't be a point in using perforated film without a bleeder cloth anyways. Also it's advisable to use a breather cloth over your non-perforated film to get a better vacuum.

@thecarbonfibernation 4 ай бұрын

To add to this point, pre-preg materials have a carefully controlled resin to material ratio in order to optimize strength and weight. Using perforated release film removes resin that is needed for the material to cure properly. Resin starved parts are brittle and subject ro cracking.

@ilanSniping 7 ай бұрын

What clear coat is that ?

@autogeek23 9 ай бұрын

Very nice!

@jeromedouillere3444 9 ай бұрын

Bravo quelle patience !

@ThatOneChannelinAZ 9 ай бұрын

Welcome back. your content is missed. I hope you're doing well.

@chrikimck 8 ай бұрын

에코님은 카카오 물티슈를 너무 좋아하심🙂

@vanchaa1 9 ай бұрын

Do you use any protection on your hands? We never work whitout gloves on prepreg. It still very hazardous

@sdasclk1861 6 ай бұрын

😂

@stevebell3537 6 ай бұрын

Not so much the hands but breathing it in

@jeanfrancoispoivre4438 9 ай бұрын

Magnifique ❤️

@nunuland69 9 ай бұрын

What's your opinion on the prepeg dry carbon fiber then resin infusion? Is dry carbon lighter? I feel from watch your vids that carbon infusion is easier to manipulate into tight spaces than prepeg c.f. thanks!!

@user-ul7el1lo4r 9 ай бұрын

Легче и крепче.

@ThomasEvoSam 3 ай бұрын

Hello there. I have a question What kind of mechanism you use to remove the inside air from the bag?

@chang5dayo 4 ай бұрын

녹이나서 구멍이 길게 난 자동차의 하부에 가본으로 덥을 생각이 있어 정보를 찾던중에 들르게 되었습니다. 뜨거운 열을 가하지 않고 철에 잘 붙게 하는 방법은 없을까요?

@user-dg4bb5td7q 9 ай бұрын

바이크 카본휠도 만드실수 있을듯 합니다.

@bluelake777 9 ай бұрын

늘 기다리고 있습니다

@ignantf00 2 ай бұрын

great job! that clear spray doesnt turn yellow\green with all the heat in the engine bay?

@junyoung458 9 ай бұрын

8:45 에폭시를 섞은 후 진공챔버에서 degasing 과정은 필요 없나요? 부품에 칠하는 과정에서 공기 기포가 어차피 들어가게 되나요?

@volare2378 9 ай бұрын

저정도 얇은 두께로 올릴경우에는 딱히 탈포과정이 필요해 보이지는 않네요~탈포를 하더리도 사실상 붓 사이의 공간을 통해서 기포가 발생할수는 있지만 도포 이후 오븐에 들어가면서 열에 의해 탈포가 되기도 할것같네요ㅎㅎ

@ariklotia3958 8 ай бұрын

Ok can you explain why the first time you put item in the heater your numbers staid the same compare 2nd time your numbers were cleared out… I could only image you’re it using that small heater..

@user-pf6nb3vn1i 9 ай бұрын

0:46 Prepreg Carbon Fiber (Dry Carbon Fiber) 안녕하세요. 프리프레그도 드라이 카본이라고 표현을 하는 건가요?? 드라이는 레진함침이 안되어있는 상태일 때 쓰는 용어인 줄 알았는데 궁금합니다~

@ECOLAPStudio 9 ай бұрын

안녕하세요 말씀하신 것이 맞습니다 본래 레진함침이 되어있지 않은 상태의 카본섬유를 드라이카본이라 부르는 것이 맞습니다 하지만 자동차쪽에선 프리프레그로 만들어진 파츠를 드라이카본이라 부르고 있습니다

@user-pf6nb3vn1i 9 ай бұрын

@@ECOLAPStudio 아 그렇군요 처음 알았습니다. 항상 좋은영상 감사합니다.

@volare2378 9 ай бұрын

프리프레그카본은 레진으로 도막층이 형성되어있지 않아 드라이카본이라 부르는것 같아요

@user-be6hl5tc2t 9 ай бұрын

Подскажите хороший современный учебный материал по изготовлению карбоновых деталей

@3toedSloth75 9 ай бұрын

Should use sealed, not perforated, release film with prepreg. Otherwise, some of the "perfect ration" of resin will leak past the film and cause voids (pinholes, etc.).

@joscythe556 9 ай бұрын

Exactly, also there is really no point in using perforated film if you don't use a bleeder cloth.

@Alex_Artix 5 ай бұрын

Что за препрег использовался и какой плотности? И температура запекания тоже интересна

@rafakalisz7761 9 ай бұрын

no no fajnie Ci to wyszło :)

@neostarfromearth107 23 күн бұрын

nice job, thanks for sharing :-)

@elnolasco Ай бұрын

Excellent videos! Help me a lot What kind of towels do you use for cleaning the carbon parts? Thanks

@andihema132 7 ай бұрын

The best 👏🏻👏🏻

@user-ci4cj5eq4x 8 ай бұрын

What's going to be made next?!

@Atipecomputers 7 ай бұрын

awesome

@thenka197 7 ай бұрын

Where do you buy the carbon I need to order some..???

@sofuzzywuzzy 7 ай бұрын

Have you ever done something much larger, like an E61 panoramic sunroof?

@sniperkotakelor 6 ай бұрын

I want to know what is the name of the carbon material used in it

@CarbonFiber-nd2sq 9 ай бұрын

Nice

@robSTI 9 ай бұрын

WOOOW TOP DIY

@gurt300 6 ай бұрын

You should not do the bagging like infusion but put the entire mold in a vacuum bag with absorbant material after the release film. And also keep vacuum during curing

@teor7809 9 ай бұрын

기다렸습나다

@sttm1283 9 ай бұрын

why all the creases(wavyness) on the sealant tape? wouldnt it be better to just lay it flat? nice engine cover... nice work.

@seadog9534 9 ай бұрын

The bag would bridge if enough slack is not present

@user-ol3pu8hg9j 9 ай бұрын

형 살아있었구나

@bigcar_kr 9 ай бұрын

언니 살아있을줄 알았다구!!!!!

@vinkenwood8233 6 ай бұрын

Suché díly? Ony se daji v troubě vyrábět i mokré díly??

@user-gc4yn2os2n 7 ай бұрын

Где купить такой карбон ?

@Samuele.Deganello 9 ай бұрын

Hi Philip wellcome back😉... this system is very good but in my opinion you not learn to work... i things this that too too simple. But i think it an very good system for the big industry where production times are of the essence. in any case great idea😉

@pb6839 9 ай бұрын

Spray with the spray can at 90° so that the paint layer is even

@sonaki_custom 9 ай бұрын

오븐이 있어서 나도 하나 만들어 볼까 하고 들어 왔는데, 전문가들이 돈을 받아야 하는 이유를 알게 되는 영상!

@sergioveron8018 9 ай бұрын

Haces llanta de bicicleta r.28?

@mark675 9 ай бұрын

The 3d printed mounts in a high temp environment? Hmm

@user-hd2hp7qn4k 9 ай бұрын

엠포도 좀 보여줘요 ㅠㅠ

@lotuselansteve 2 ай бұрын

Good job, but perforated film is used for wet lay. Unperforated film is used for prepreg as the resin to carbon ratio is correct so you don't want to remove any of it.

@johnrichardson82 2 ай бұрын

Where do you buy carbon fiber like this video has

@user-dg4bb5td7q 9 ай бұрын

마지막에 3D프린터로 만든 마운트는 오래 못버티지 싶은데요 카본으로 한번 더빵 했으면 완벽했을뜻

@baesundal 9 ай бұрын

카본 섬유는 어디서 사야 하나요?

@user-pf6nb3vn1i 9 ай бұрын

소량구매하시는거면 인터넷사이트 '화이바맨' 이나 'FRP 샵' 에서 구매하실 수 있습니다.

@meanza666 9 ай бұрын

Can you make a motorcycle frame for me? I like your work.

@premiumannelie4474 9 ай бұрын

Respekt !!!!!

@mohammadrasoulfard-habibi3066 9 ай бұрын

This legend got me into this, brilliant video as always mate.

@Trumppower 9 ай бұрын

Better buy a Easy Composites Oven and Pump if you want to do this right. It's too expensive to make mistakes with this material.

@lotuselansteve 2 ай бұрын

Agree with a decent pump, but the EC oven's base price is over £1700! A standard oven works well if you use a digital temp sensor to monitor the temp.

@kevinkev1530 9 ай бұрын

👍🏾👍🏾

@itsjustWebbie 8 ай бұрын

Its time for a vacuum pump homie...😂

@thomashellstrom9514 Ай бұрын

👏🏻👏🏻🤩

@deniskablukov4404 7 ай бұрын

Выглядит красиво, но меня волнует крепление нейлоновых ножек. У полиамида достаточно тяжело клеиться. Вы же используете эпоксидную смолу. Я пробовал также клеить издели из полиамида, только они были армированы стекловолокном. Результат был плохой. Все выглядело хорошо, но при небольшом усилии весь клеевой слой откалывался

@Markelboomin 23 күн бұрын

Why so many layers (legit question)?

@Phoenix_0777 7 ай бұрын

Please, fix retracts on your ender 3...

@user-kv8mu5td5h 9 ай бұрын

손이 좀 탔네요 ㅋㅋ

@woonsa0 9 ай бұрын

사이트 링크 접속이 안되요

@JuanTorres-ly1rq 6 ай бұрын

Can we request part. And if so would sell it back to me😅 97 lexus sc400 center console

@alfalfasprout69 Ай бұрын

Is this master at work in side his house?

@Karma_Gear 18 күн бұрын

great video,but where is my Mpower

@teleris6971 6 ай бұрын

Wieviel soll so ein Bauteil real kosten? $ 500?

@mmsarracino 9 ай бұрын

you need a refrigerator compressor as a vacuum pump

@505vlad 8 ай бұрын

Release agent= sunflower oil xd

@user-fn3iu1ty6n 9 ай бұрын

오이오이!!!! 기다렸다고!!!!!!

@user-vk3ut6bx2n 9 ай бұрын

Hello, you keep getting the cooking process wrong, first of all you should build yourself a large and co-operated oven, then you don't have to put the micro-perforated blue film but the red film for high temperatures and above this the aerating cloth. If you keep getting holes or you make a mistake in laminating, you either leave the bag hanging in the corners, or you need to correct the firing.👍